DigiTech DOD250-13

DOD 오버드라이브 250 아날로그 오버드라이브 프리amp 사용자 설명서

Model: DOD250-13

소개

The DOD Overdrive Preamp 250 is a legendary analog overdrive pedal designed for guitar and bass instruments. This manual provides essential information for setting up, operating, maintaining, and troubleshooting your DOD Overdrive 250 to ensure optimal performance and longevity.

설정

페달에 전원 공급

The DOD Overdrive 250 can be powered by a single 9V alkaline dry battery or an optional 9V DC power supply (PS0913DC). Ensure the power source is correctly connected before use.

DOD Overdrive 250 pedal showing the 9V DC power supply input jack on the side.

그림 1: Power Supply Connector. Connect a 9V DC power adapter here.

페달 연결하기

악기를 다음에 연결하십시오. IN jack on the right side of the pedal using a standard 1/4-inch instrument cable. Connect the 밖으로 페달 왼쪽의 잭을 당신의 것에 연결하세요 amp앰프나 신호 체인의 다음 페달에 다른 1/4인치 악기 케이블을 사용하여 연결하십시오.

DOD Overdrive 250 pedal showing the input and output jacks on the sides.

그림 2: Input and Output Jacks. The input jack is on the right, and the output jack is on the left.

페달 조작하기

The DOD Overdrive 250 features two primary control knobs: 얻다 그리고 수준, along with a footswitch and an LED indicator.

맨 위 view of the DOD Overdrive 250 pedal showing the Gain and Level knobs, footswitch, and blue LED.

그림 3: Front Panel Controls. The Gain and Level knobs are at the top, with the footswitch and LED below.

통제 수단

  • 이득: This knob controls the amount of overdrive or distortion applied to your signal. Turning it clockwise increases the saturation, ranging from a subtle grit to a full, aggressive grind.
  • 수준: This knob adjusts the overall output volume of the pedal. It can be used to match the bypassed signal volume, or to provide a significant boost for solos or to push your amplifier harder. With the Gain set low, increasing the Level can provide a clean boost.

풋스위치 및 LED 표시기

The large footswitch activates or bypasses the effect. When the effect is active, the crisp blue LED indicator will illuminate, providing clear visual feedback of the pedal's status.

DOD Overdrive 250 pedal with an arrow pointing to the blue LED indicator.

그림 4: Crisp Blue LED Indication. The LED illuminates when the effect is active.

진정한 우회

The DOD Overdrive 250 features true bypass circuitry. This means that when the pedal is disengaged (effect off), your guitar's signal passes directly through the pedal without any electronic interference, preserving your original tone. This is a significant improvement over older designs that could color the bypassed signal.

유지

배터리 교체

If using a 9V battery, replace it when the LED indicator dims or the pedal's performance degrades. To replace the battery, carefully remove the bottom plate of the pedal. Disconnect the old battery and connect a new 9V alkaline battery, ensuring correct polarity. Securely reattach the bottom plate.

청소

Wipe the pedal's exterior with a soft, dry cloth. Avoid using abrasive cleaners or solvents, as these can damage the finish and internal components.

저장

When not in use for extended periods, disconnect the power supply or remove the battery to prevent leakage and preserve battery life. Store the pedal in a cool, dry place away from direct sunlight and extreme temperatures.

문제 해결

문제가능한 원인해결책
소리가 나지 않거나 신호가 약함Incorrect cable connections, dead battery, faulty power supply, pedal not engaged.Check all cable connections. Replace 9V battery or verify power supply connection. Ensure the pedal is engaged (blue LED on). Test with different cables.
원치 않는 소음이나 윙윙거림Ground loop, faulty cables, interference from other electronics, power supply issues.Ensure all equipment is properly grounded. Try different cables. Move pedal away from power transformers or fluorescent lights. Use a regulated power supply.
LED가 켜지지 않습니다No power, dead battery, faulty LED.Check power supply or replace battery. If problem persists, contact support.

명세서

특징세부 사항
모델DOD250-13
치수(길이 x 너비 x 높이)4.88 x 2.61 x 3.25 인치
무게9.92 ounces (~0.62 lbs)
입력1/4-inch Instrument
출력1/4-inch Instrument
섀시 소재All Metal (Aluminum)
전원 공급 장치9V Alkaline Dry Battery or 9V DC (PS0913DC)
신호 형식비슷한 물건
색상Yellow Metallic Flake

보증 및 지원

For detailed warranty information, please refer to the documentation included with your purchase or visit the official DigiTech website. DigiTech provides support for their products through their authorized service centers and online resources.

You can find more information and contact support via the official DigiTech store: 아마존에서 DigiTech 스토어를 만나보세요..

Note: No official product videos from the seller were found in the provided data to be embedded in this manual.

관련 문서 - DOD250-13

사전view 디지텍 RP-10 기타 신호 처리기/풋 컨트롤러 및 프리앰프amp 사용 설명서
이 사용 설명서는 DigiTech RP-10 기타 신호 처리기/풋 컨트롤러 및 프리앰프에 대한 포괄적인 정보를 제공합니다.amp설정, 작동, 프로그래밍, 효과 및 MIDI 기능을 다룹니다.
사전view 디지텍 RP-6 기타 신호 처리기/풋 컨트롤러 및 프리앰프amp 사용 설명서
DigiTech RP-6 기타 신호 처리기/풋 컨트롤러 및 프리앰프에 대한 종합 사용 설명서amp해당 제품의 특징, 작동 방식, 효과, 매개변수, 사양 및 설정 방법을 자세히 설명합니다.
사전view DigiTech RP-1 기타 이펙트 프로세서/컨트롤러 및 프리앰프amp 사용 설명서
DigiTech RP-1에 대한 포괄적인 사용 설명서로, 기타리스트를 위한 기능, 작동, 프로그래밍, MIDI 구현 및 보증 정보를 자세히 설명합니다.
사전view 디지텍 RP-5 기타 신호 처리기/풋 컨트롤러 및 프리앰프amp 사용 설명서
DigiTech RP-5 기타 신호 처리기/풋 컨트롤러 및 프리앰프에 대한 종합 사용 설명서amp이 문서에서는 S-DISC 프로세서의 특징, 제어 방식, 효과, 파라미터, 설정 방법 및 사양을 자세히 설명합니다. 스튜디오 및 라이브 환경에서 S-DISC 프로세서를 사용하는 방법을 알아보세요.
사전view DigiTech HardWire CM-2 튜브 오버드라이브 사용 설명서
DigiTech HardWire CM-2 Tube Overdrive 기타 이펙트 페달의 사용 설명서로, 기능, 작동법, 안전 지침, 보증 및 사양에 대한 자세한 설명이 나와 있습니다.
사전view DigiTech Bass Driver 베이스 오버드라이브/디스토션 페달 - 사용 설명서
DigiTech Bass Driver 베이스 오버드라이브/디스토션 페달의 종합 사용 설명서입니다. AudioDNA™ 기술, 컨트롤(레벨, 톤, 블렌드, 모프), 연결(입력, 출력 1)에 대해 알아보세요. Amp, CIT™ 캐비닛 모델링을 탑재한 Out 2 믹서), 설치, 배터리 교체, 안전 지침 및 보증 정보.