소개
Thank you for choosing the Hunter PGV201 2-Inch Globe/Angle Valve with Flow Control. This heavy-duty valve is designed for reliable performance in residential and light commercial irrigation systems. This manual provides essential information for proper installation, operation, and maintenance to ensure optimal functionality and longevity of your valve.
안전 정보
경고: Handle with care to avoid water pressure damage. Ensure proper electrical connections to prevent hazards. Always turn off the main water supply and electrical power to the irrigation system before performing any installation, maintenance, or repair work on the valve.
- 장갑, 눈 보호 장비 등 적절한 개인 보호 장비(PPE)를 착용하세요.
- 설치하기 전에 해당 지역의 건물 및 배관 규정을 확인하세요.
- Do not exceed the maximum pressure rating of 150 PSI.
- 모든 연결 부분이 방수 처리되어 누수가 발생하지 않도록 하세요.
설정 및 설치
Proper installation is crucial for the performance and lifespan of your PGV201 valve. Follow these steps carefully:
- 사이트 준비: Excavate a trench to the desired depth, ensuring adequate space for the valve and piping.
- 물 공급을 차단하세요: 관개 시스템의 주 급수 차단 밸브를 찾아 완전히 잠그십시오.
- 배관 연결: The PGV201 is a 2-inch valve. Connect the inlet side of the valve to the main water line and the outlet side to the irrigation zone piping. Use appropriate fittings and sealants to ensure watertight connections. The valve can be installed in either a globe or angle configuration.
- 전기 배선: Connect the valve's solenoid wires to your irrigation controller's common wire and the specific zone wire. Ensure all electrical connections are secure and protected from moisture. Refer to your irrigation controller's manual for specific wiring instructions.
- 누출 테스트: Slowly turn on the main water supply and inspect all connections for leaks. Address any leaks immediately.
- 테스트 작업: Manually activate the valve or use your irrigation controller to cycle the zone and ensure proper water flow.
작동 지침
수동 조작
The PGV201 valve can be operated manually for testing or maintenance purposes:
- 수동으로 열려면: Turn the solenoid counter-clockwise approximately one-quarter to one-half turn. Water will begin to flow.
- 수동으로 닫으려면: Turn the solenoid clockwise until it is finger-tight. Water flow will stop. Do not overtighten.
Flow Control Adjustment
The flow control feature allows you to adjust the amount of water flowing through the valve, which can be useful for fine-tuning sprinkler performance or reducing water hammer.
- 혈류량을 줄이려면: 유량 조절 손잡이를 시계 방향으로 돌리세요.
- 혈류량을 늘리려면: 유량 조절 손잡이를 시계 반대 방향으로 돌리세요.
- Full Flow: Turn the knob fully counter-clockwise.
- 끄다: Turn the knob fully clockwise to shut off water flow to the zone.
Adjust the flow control while the valve is open and water is flowing to observe the effect on your sprinklers.
유지
Regular maintenance helps ensure the longevity and efficient operation of your PGV201 valve.
- 계절별 점검: Periodically inspect the valve for any visible damage, leaks, or debris accumulation.
- 필터 청소(해당되는 경우): Some systems may have an inline filter before the valve. Clean or replace it as needed.
- 겨울철 : In freezing climates, it is essential to properly winterize your irrigation system, including draining water from the valves, to prevent freeze damage. Consult a local irrigation professional if unsure.
- 횡격막 검사: If the valve is not operating correctly, the diaphragm may need inspection or replacement. This typically involves unscrewing the top of the valve. Ensure the water supply is off before attempting this.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 밸브가 열리지 않음 | No power to solenoid, faulty solenoid, clogged diaphragm, closed flow control. | Check wiring and controller. Test solenoid. Clean or replace diaphragm. Ensure flow control is open. |
| 밸브가 닫히지 않음 | Debris in valve, worn diaphragm, faulty solenoid. | Turn off water, disassemble and clean valve. Inspect and replace diaphragm. Test or replace solenoid. |
| Water leaks from valve | Loose connections, cracked housing, worn O-rings or diaphragm. | Tighten connections. Inspect housing for cracks. Replace O-rings or diaphragm. |
| 수압/유량 부족 | Partially closed flow control, clogged filter, main water supply issue. | Adjust flow control. Clean inline filter. Check main water supply pressure. |
명세서
- 모델: PGV201
- 입구 연결 크기: 2 인치
- 최대 압력: 150 PSI(평방 인치당 파운드)
- 최대 유량 : 150 GPM(분당 갤런)
- 재료: 플라스틱
- 제품 크기(길이 x 너비 x 높이): 5 x 7 x 10 인치
- 품목 무게: 1.2파운드
- 상표: 사냥꾼
- 제조업체: Standard Plumbing Supply-LG
- 한국어: 603981394160
보증 및 지원
For warranty information and technical support, please refer to the official Hunter website or contact Hunter customer service directly. Keep your purchase receipt as proof of purchase.
Hunter Customer Support: www.hunterindustries.com/support