NZXT Sentry Mix 2 Fan Controller (AC-SEN-MIX2-M1) User Manual

1. 서론

The NZXT Sentry Mix 2 is a 6-channel fan controller designed to provide precise control over your computer's cooling system. Each channel delivers up to 30 watts of power, allowing for comprehensive management of multiple fans. This device features a matte-black finish with customizable LED lighting, integrating seamlessly into various PC builds. This manual provides instructions for the proper installation, operation, and maintenance of your Sentry Mix 2 fan controller.

2. 안전 정보

• 설치 또는 유지 보수를 하기 전에 컴퓨터의 전원이 꺼져 있고 벽면 콘센트에서 플러그가 뽑혀 있는지 확인하십시오.
• Handle electronic components with care to avoid electrostatic discharge (ESD). Consider using an anti-static wrist strap.
• Do not exceed the maximum power output of 30 watts per channel. Overloading a channel can damage the controller and connected components.
• Connect only standard PC cooling fans or compatible water cooling pumps. Do not connect high-power industrial fans (e.g., Delta fans) as they can damage the unit.
• 기기를 액체와 과도한 습기로부터 멀리하세요.
• Do not attempt to open or modify the controller. This will void the warranty and may cause damage.

3. 패키지 내용

패키지에 모든 구성 요소가 들어 있는지 확인하세요.

• NZXT Sentry Mix 2 Fan Controller
• 장착 나사
• Fan Extension Cables (if included)
• Power Cables (2x Molex connectors)

4. 설정 및 설치

4.1. 물리적 설치

1. PC를 준비하세요: Power off your computer and unplug it from the wall. Open your PC case to access the internal components.
2. Locate a 5.25-inch bay: The Sentry Mix 2 is designed to fit into a standard 5.25-inch drive bay. Remove the front panel cover from an available bay.
3. Insert the controller: Carefully slide the Sentry Mix 2 into the chosen 5.25-inch bay from the front of the case until the mounting holes align.
4. Secure the controller: Use the provided screws to secure the fan controller to the drive bay on both sides.

그림 1: 앞쪽 view of the NZXT Sentry Mix 2 Fan Controller, showing the six matte-black sliders and the NZXT logo. This image illustrates the device's appearance when installed in a 5.25-inch bay.

4.2. Connecting Fans

1. Identify fan connectors: The Sentry Mix 2 has six 3-pin fan headers on its rear. Each header corresponds to a slider on the front panel.
2. Connect your fans: Plug your PC case fans or CPU cooler fans (if compatible) into the desired fan headers on the back of the Sentry Mix 2. Ensure the connectors are properly seated.
3. 케이블 관리: Route the fan cables neatly to avoid obstructing airflow or interfering with other components.

그림 2: 뒤쪽 view of the NZXT Sentry Mix 2 Fan Controller, showing the six fan headers with cables connected. This image demonstrates how fans are plugged into the controller's output ports.

4.3. 전원 연결

1. Locate Molex connectors: The Sentry Mix 2 requires power from your PC's power supply unit (PSU) via two Molex connectors.
2. 전원 연결: Plug two available Molex power connectors from your PSU into the corresponding Molex inputs on the back of the Sentry Mix 2. Ensure a firm connection.
3. 사건 종결: Once all connections are made and verified, close your PC case and reconnect the power cable to the wall outlet.

5. 사용 설명서

5.1. 팬 속도 제어

The Sentry Mix 2 features six individual sliders on the front panel, each controlling one fan channel. Moving a slider up increases the fan speed and airflow, while moving it down decreases the fan speed, resulting in quieter operation.

• 개별 제어: Adjust each slider independently to fine-tune the speed of connected fans.
• Initial Spin-up: Upon PC startup, fans connected to the Sentry Mix 2 will briefly spin at full speed for approximately 10 seconds to ensure proper initiation, then revert to their set slider speed. This is normal operation.

그림 3: 클로즈업 view of the NZXT Sentry Mix 2's six fan speed sliders. Each slider allows for manual adjustment of fan RPM, providing granular control over cooling performance and noise levels.

5.2. LED 조명 제어

The Sentry Mix 2 includes integrated color LED lighting. A small button located on the left side of the front panel allows you to cycle through five different LED colors (red, green, blue, orange, white) or turn the lighting off completely.

• 색상 선택: Press the LED button repeatedly to change the display color.
• LED 끄기: Continue pressing the button until the LEDs turn off, if desired.

6. 유지관리

• 청소: Periodically clean the front panel of the controller with a soft, dry cloth. Avoid using harsh chemicals or abrasive materials.
• 먼지 제거: If dust accumulates inside the PC case, carefully remove the controller and use compressed air to clean any dust from the internal components and connectors. Ensure the PC is powered off and unplugged before cleaning.
• 케이블 점검: Occasionally check all connected cables (fan and power) to ensure they are securely seated and not damaged.

7. 문제 해결

7.1. Fans Not Spinning

• 전원 확인: Ensure both Molex power connectors from the PSU are securely connected to the Sentry Mix 2.
• 팬 연결 상태를 확인하세요: Verify that the fan cables are correctly and firmly plugged into the controller's fan headers.
• Slider Position: Confirm that the corresponding slider for the non-spinning fan is not set to its lowest position. Move it up to increase power.
• 팬 기능: Test the fan by connecting it directly to a motherboard fan header to rule out a faulty fan.

7.2. LEDs Not Lighting Up or Changing Color

• 전원 확인: Ensure the controller is receiving power via the Molex connectors.
• 버튼을 누르시오: Press the LED control button on the front panel to cycle through colors or turn the LEDs on.

7.3. Intermittent Fan Operation

• 보안 연결: Re-check all fan and power connections for looseness.
• 초과 적재: 총 와트를 보장tage of fans connected to a single channel does not exceed 30 watts.

8. 사양

9. 보증 및 지원

보증 정보 및 기술 지원에 대해서는 NZXT 공식 웹사이트를 참조하십시오. web웹사이트를 방문하거나 NZXT 고객 서비스 센터에 문의하십시오. 보증 청구를 위해 구매 증빙 자료를 보관하십시오.

NZXT 공식 Web대지: www.nzxt.com