Puig 4322N Rear Stand for Conventional Swingarm

소개

The Puig 4322N Rear Stand is designed to provide stable support for motorcycles with conventional swingarms. Constructed from high-resistance steel with a black epoxy paint finish, this stand ensures durability and corrosion protection. It is ideal for various tasks including maintenance, cleaning, lubrication, part replacement, and secure long-term parking, helping to extend the vehicle's lifespan and facilitate care.

안전 정보

• Always ensure the motorcycle is on a flat, stable, and non-slip surface before using the stand.
• Verify that the stand is correctly positioned under the swingarm spools or contact points before lifting.
• Never leave the motorcycle unattended while it is on the stand, especially during initial setup.
• Do not exceed the weight capacity of the stand. While not explicitly stated, exercise caution with heavy motorcycles.
• 들어올리고 내리는 작업 중에는 움직이는 부품에 손과 발이 닿지 않도록 주의하세요.
• Regularly inspect the stand for any signs of damage, wear, or corrosion. Do not use a damaged stand.
• 장갑, 보안경 등 적절한 개인 보호 장비(PPE)를 사용하십시오.

패키지 내용

패키지에는 다음이 포함됩니다.

• One Puig 4322N adjustable steel motorcycle rear stand.
• Necessary hardware for assembly (if applicable, typically pre-assembled or minimal assembly).

설정 및 조립

The Puig 4322N rear stand is designed for straightforward assembly. Most units come partially assembled, requiring minimal final setup.

1. 구성 요소 풀기: 모든 부품을 포장에서 조심스럽게 꺼내세요. 모든 구성품이 들어 있고 손상되지 않았는지 확인하세요.
2. 메인 프레임 조립: If the main frame is not pre-assembled, connect the two main stand arms using the provided fasteners. Ensure all bolts are tightened securely.
3. Attach Swingarm Supports: Install the swingarm support pads or spools onto the stand arms. These are typically adjustable to accommodate different swingarm widths.
4. 너비 조정: Place the stand behind your motorcycle. Adjust the width of the swingarm supports to match the width of your motorcycle's swingarm or spools. Ensure a snug fit without being too tight.
5. 최종 확인: Before use, double-check all connections and adjustments to ensure the stand is stable and ready.

작동 지침

Follow these steps to safely lift and lower your motorcycle using the Puig 4322N rear stand.

1. 오토바이 준비: Ensure the motorcycle is in neutral gear and on its side stand.
2. 위치 스탠드: Place the rear stand behind the motorcycle. Align the stand's support pads or spools with the motorcycle's swingarm or spools. Ensure the stand is centered and the contact points are secure.
3. Lift Motorcycle: While holding the motorcycle upright with one hand on the handlebar or rear grab handle, firmly push down on the stand's lever arm with your foot or other hand. The motorcycle's rear wheel should lift smoothly off the ground. Ensure the stand's feet are flat on the ground and stable.
4. 안정성 확인: Once lifted, gently rock the motorcycle to confirm it is stable on the stand.
5. Lower Motorcycle: To lower, firmly hold the motorcycle upright. Place one foot on the stand's lever arm and carefully lift the stand's handle, allowing the motorcycle to gently descend onto its wheels and side stand.

유지

Proper maintenance ensures the longevity and safe operation of your Puig 4322N rear stand.

• 정기 청소: 광고로 스탠드를 닦아주세요amp cloth to remove dirt, grease, and debris.
• 손상 여부 검사: Periodically check the steel frame for dents, bends, cracks, or signs of corrosion. Inspect the epoxy paint for chips that could expose the metal to rust.
• 패스너 확인: Ensure all bolts, nuts, and pivot points are tight. Re-tighten if necessary.
• 움직이는 부품에 윤활유를 바르세요: If the stand has pivot points or adjustable mechanisms, apply a small amount of appropriate lubricant to ensure smooth operation.
• 올바르게 보관하세요: When not in use, store the stand in a dry environment to prevent rust and damage.

문제 해결

If you encounter issues while using your rear stand, consider the following:

• Motorcycle feels unstable:
  • Ensure the stand is on a perfectly flat and level surface.
  • Verify that the swingarm supports are correctly adjusted to the motorcycle's width and are making full contact with the swingarm or spools.
  • Confirm all fasteners on the stand are securely tightened.
• Difficulty lifting the motorcycle:
  • Ensure the stand's lever arm is fully depressed.
  • Check that the motorcycle's weight is within a manageable range for a single person to lift with the stand.
  • Verify that the stand's wheels are rolling freely.
• Stand appears damaged:
  • Do not use the stand if any structural components are bent, cracked, or severely corroded. Contact Puig support for assistance.

명세서

보증 및 지원

For warranty information or technical support regarding your Puig 4322N Rear Stand, please refer to the documentation provided with your purchase or visit the official Puig website. Contact their customer service for any inquiries or assistance.

Official Puig Web대지: www.puig.tv