1. 서론
This instruction manual provides comprehensive guidance for the installation, configuration, and operation of the JASCO GE Z-Wave On/Off Relay Switch, Model 45609 (ZW4001). This device is designed to integrate into your Z-Wave wireless lighting control system, enabling remote ON/OFF control of permanently installed lighting fixtures and ceiling fans.
The GE Z-Wave On/Off Relay Switch offers a convenient solution for smart home automation, compatible with various lighting types including CFL, LED, Xenon, Halogen, Fluorescent, and Incandescent. It supports both 2-way and 3-way wiring configurations when used with an auxiliary switch.
2. 중요한 안전 정보
경고: 감전의 위험이 있습니다. 설치에는 많은 양의 데이터가 필요합니다.tage wiring. Improper installation can result in serious injury or death. Always consult a qualified electrician if you are unsure about any part of the installation process.
- 전원 분리: Before installation, turn OFF the power to the switch location at the circuit breaker or fuse box.
- 중성선이 필요합니다: This switch requires a neutral wire for operation. If your existing switch box does not have a neutral wire, consult a qualified electrician.
- 실내 전용: 이 장치는 건조한 실내 환경에서 사용하도록 설계되었습니다.
- LOAD COMPATIBILITY: Ensure the connected load does not exceed the switch's maximum rating.
- 팬 제어: This switch provides ON/OFF control for ceiling fans; speed control is not supported.
3. 패키지 내용
- GE Z-Wave On/Off Relay Switch (Model 45609 / ZW4001)
- Wiring Nuts (typically included, but may vary)
- 사용 설명서(본 문서)
메모: A wallplate is not included and must be purchased separately.
4. 설정 및 설치
Follow these steps carefully to install your GE Z-Wave On/Off Relay Switch. If you are unfamiliar with electrical wiring, please consult a qualified electrician.
4.1 배선도view
The switch requires Line (Hot), Load, Neutral, and Ground connections. For 3-way installations, an auxiliary switch (e.g., GE 45610) and a traveler wire are also required.
그림 1: 앞쪽 view of the GE Z-Wave On/Off Relay Switch (Model 45609) without a wallplate, showing the rocker switch and mounting bracket. The "TOP" indicator is visible at the top of the metal bracket. Electrical ratings (120VAC, 60Hz, 15A Resistive Load) are printed on the side.
4.2 설치 단계
- 전원 끄기: Locate the circuit breaker or fuse that supplies power to the switch box. Turn it OFF completely. Verify power is off using a voltag전자 테스터.
- 기존 스위치 제거: Carefully remove the wallplate and unscrew the existing switch from the wall box. Disconnect the wires from the old switch, noting which wire was connected to which terminal. It is recommended to label the wires (Line, Load, Neutral, Ground, Traveler if applicable).
- 전선 식별:
- (핫라인): Connects to the electrical panel, providing power.
- 짐: Connects to the light fixture or fan.
- 중립적: Typically white, required for the switch to operate.
- 지면: 구리선 또는 녹색 전선.
- 여행자 (3자 통화용): Connects to the auxiliary switch.
- Wire the Z-Wave Switch: Connect the wires to the GE Z-Wave switch terminals as follows:
- 접지선: Connect to the green GROUND terminal.
- 중성선: Connect to the white NEUTRAL terminal.
- 라인(핫) 와이어: Connect to the black LINE terminal.
- 부하 와이어: Connect to the black LOAD terminal.
- Traveler Wire (if 3-way): Connect to the red TRAVELER terminal. Cap off the traveler wire if not used.
- 스위치 장착: Carefully fold the wires and push the switch into the wall box. Secure the switch with the provided screws.
- 월플레이트 설치: Attach the new wallplate (not included) over the switch.
- 복원력 : 회로 차단기에서 전원을 다시 켜세요.
- 테스트 기능: Manually press the rocker switch to ensure the connected light or fan turns ON and OFF.
그림 2: 앞쪽 view of the GE Z-Wave On/Off Relay Switch (Model 45609) with a light almond wallplate installed. This illustrates the finished appearance of the switch in a standard electrical box.
5. 사용 설명서
5.1 수동 제어
The GE Z-Wave On/Off Relay Switch can be operated manually:
- Press the top of the rocker switch to turn the connected device ON.
- Press the bottom of the rocker switch to turn the connected device OFF.
- An LED indicator on the switch illuminates to show its location in a dark room.
5.2 Z-Wave 네트워크 연결(페어링)
To add the switch to your Z-Wave network:
- Place your Z-Wave controller into inclusion (pairing) mode. Refer to your controller's instruction manual for specific steps.
- Once the controller is in inclusion mode, quickly tap the top or bottom of the rocker switch once. The LED indicator on the switch may flash to confirm inclusion.
- The controller will confirm successful inclusion. You can now control the switch remotely through your Z-Wave network.
메모: Pairing typically requires a light, quick tap, not a prolonged press.
5.3 Z-Wave 네트워크 제외(페어링 해제)
To remove the switch from your Z-Wave network:
- Place your Z-Wave controller into exclusion (unpairing) mode. Refer to your controller's instruction manual for specific steps.
- Once the controller is in exclusion mode, quickly tap the top or bottom of the rocker switch once. The LED indicator on the switch may flash to confirm exclusion.
- The controller will confirm successful exclusion. The switch is now removed from your Z-Wave network.
6. 유지관리
- 청소: 스위치를 청소하려면 부드러운 천으로 닦으세요.amp 천. 연마성 세척제나 용매를 사용하지 마십시오.
- 사용자가 수리할 수 없는 부품: 스위치 내부에는 사용자가 수리할 수 있는 부품이 없습니다. 기기를 열거나 수리하려고 시도하지 마십시오.
- 펌웨어 업데이트: Any firmware updates would be managed through your Z-Wave controller, if supported.
7. 문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| Light/Fan does not turn ON/OFF manually. |
|
|
| Switch does not respond to Z-Wave controller. |
|
|
| LED indicator is not working. |
|
|
8. 사양
| 특징 | 세부 사항 |
|---|---|
| 모델 번호 | 45609(ZW4001) |
| 상표 | JASCO (GE) |
| 힘 | 120VAC, 60Hz |
| 최대 부하 | 15A 저항 부하 |
| 무선 기술 | 지웨이브 |
| 배선 구성 | 2-way or 3-way (with auxiliary switch) |
| 중성선 | 필수의 |
| 치수(길이 x 너비 x 높이) | 10.49 x 5.41 x 4.45cm (약 4.13 x 2.13 x 1.75인치) |
| 무게 | 113.4g (약 4온스) |
| 작동 모드 | 온-오프 |
| 스위치 유형 | 흔들리는 것 |
| 장착 유형 | Wall Mount (standard electrical box) |
| 컨트롤러 유형 | SmartThings (compatible with other Z-Wave controllers) |
9. 보증 및 지원
For warranty information and technical support, please refer to the documentation provided with your purchase or visit the JASCO Products web사이트. 보증 청구를 위해 구매 증빙 자료를 보관하세요.
JASCO Products provides customer support for their Z-Wave devices. Contact information can typically be found on their official web사이트 또는 제품 포장에 표시되어 있습니다.
