1. 제품 오버view
The BFT P121011 Intro Key Selector is a robust, surface-mounted key switch designed for controlling access systems, such as automatic gates or doors. It features a durable plastic construction and operates with a normally closed contact type, providing a secure and reliable control mechanism.
This device utilizes a key for activation, offering a simple on-off operational mode. It is designed for a single-circuit application and connects via screw terminals for straightforward wiring.
Figure 1: BFT P121011 Intro Key Selector. This image shows the circular key selector unit, dark gray in color, with the BFT logo at the top. Below the logo, the positions 'A', '0', and 'B' are marked around the central keyhole. Two silver keys are visible in the foreground, resting on a wooden surface.
2. 안전 정보
- 설치 및 사용 전에 모든 지침을 주의 깊게 읽으십시오.
- 설치는 해당 지역의 전기 규정 및 법규에 따라 자격을 갖춘 전문가가 수행해야 합니다.
- Disconnect power to the system before performing any installation, maintenance, or troubleshooting.
- 모든 배선 연결이 안전하고 적절하게 절연되어 단락을 방지하세요.
- 기기를 극한의 온도, 습기 또는 부식성 물질에 노출시키지 마십시오.
- Keep keys out of reach of children and unauthorized personnel.
3. 사양
| 특징 | 사양 |
|---|---|
| 상표 | 비피에이치피(BFT) |
| 모델 | 피121011 |
| 작동 모드 | 온 - 오프 |
| 연락처 유형 | 일반적으로 닫힘 |
| 스위치 유형 | 열쇠 |
| 터미널 유형 | 나사 |
| 재료 | 플라스틱 |
| 치수(길이x너비x높이) | 30 x 195 x 260 cm (Note: These dimensions seem unusually large for a key selector. Please verify with product packaging.) |
| 회로 유형 | 1방향 |
| 장착 유형 | 표면 |
| 액추에이터 유형 | Button, Knob (Note: This refers to the key as the actuator) |
4. 설치 및 설정
4.1. 설치 전 점검
- 모든 구성 요소가 들어 있고 손상되지 않았는지 확인하세요.
- Ensure the mounting surface is flat, stable, and suitable for surface mounting.
- Confirm that the power supply to the gate or access system is disconnected.
4.2. 키 셀렉터 장착
- Choose an appropriate location for the key selector, ensuring it is easily accessible but protected from potential damage.
- Mark the drilling points on the mounting surface using the key selector's base as a template.
- 표시된 지점에 파일럿 구멍을 뚫습니다.
- Secure the key selector base to the surface using appropriate screws and fasteners (not included).
4.3. 배선 연결
- Route the necessary control cables through the designated entry points on the key selector's housing.
- Connect the control wires to the screw terminals inside the key selector. Refer to the wiring diagram provided with your gate or access system control unit for specific connections. The key selector typically acts as a momentary contact switch.
- 모든 연결이 단단하고 안전한지 확인하세요.
- Close the key selector housing, ensuring it is properly sealed.
4.4. 설치 후
- 시스템의 전원을 복구합니다.
- Test the key selector's functionality as described in the Operating Instructions section.
5. 사용 설명서
The BFT P121011 Intro Key Selector provides a simple, key-operated control for your access system.
- 삽입 키: Insert the provided key into the keyhole on the front of the selector.
- 활성화: Turn the key to the desired position (e.g., 'A' or 'B' if multiple functions are supported, or simply to activate the single function). The key selector is designed to provide a momentary contact closure, which signals the connected control unit to perform an action (e.g., open/close gate).
- 반환 키: After activation, return the key to the '0' (neutral) position and remove it. The key selector will return to its normally closed state.
The specific action triggered by turning the key (e.g., opening, closing, or stopping a gate) depends on how the key selector is wired to the main control unit of your access system.
6. 유지관리
Regular maintenance ensures the longevity and reliable operation of your BFT P121011 Intro Key Selector.
- 청소: Periodically clean the exterior of the key selector with a soft, damp 천. 연마성 세척제나 용매를 사용하지 마십시오.
- Keyhole Inspection: Ensure the keyhole remains free of debris. If necessary, use a small, soft brush to clear any obstructions. Avoid using lubricants that may attract dust.
- 배선 점검: Annually, or if issues arise, disconnect power and inspect the wiring connections inside the unit for any signs of corrosion or loosening. Re-tighten connections as needed.
- 핵심 조건: Inspect the keys for wear or damage. Worn keys may not operate the selector smoothly or reliably.
7. 문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| Key selector does not activate the system. | 제어 장치에 전원이 공급되지 않습니다. 배선이 잘못되었습니다. Faulty key selector contacts. |
Check power supply to the main control unit. Verify wiring connections against the system's diagram. Test the key selector's contacts with a multimeter. Replace if faulty. |
| 열쇠를 돌리거나 빼기가 어렵습니다. | Debris in keyhole. Worn key or lock mechanism. |
Clean keyhole with a soft brush. Try a different key. If issue persists, the lock mechanism may need replacement. |
| 간헐적 작동. | 느슨한 배선 연결. 환경적 간섭. |
모든 배선 연결 부분을 점검하고 조이세요. Ensure the unit is properly sealed and protected from elements. |
8. 보증 및 지원
Specific warranty information for the BFT P121011 Intro Key Selector is typically provided at the point of purchase or within the product packaging. Please refer to your purchase documentation for details regarding warranty coverage and duration.
For technical support, spare parts, or service inquiries, please contact your authorized BFT dealer or the BFT customer service department. Contact information can usually be found on the BFT official web사이트 또는 제품의 원래 설명서에서 확인하세요.