중요한 안전 정보
Read all instructions carefully before installation and use. Failure to follow these instructions could result in property damage, serious injury, or death. If you have any questions, contact Chief customer support.
- Ensure the mounting surface can support the combined weight of the mount and the projector.
- Use appropriate fasteners for your specific mounting surface.
- 최대 중량 용량은 250파운드(113.4kg)를 초과하지 마십시오.
- 설치는 자격을 갖춘 사람이 수행해야 합니다.
- 설치하는 동안 어린이와 애완동물이 접근하지 못하도록 하세요.
패키지 내용
설치를 시작하기 전에 모든 구성 요소가 있는지 확인하세요.
- Chief VCMU Projector Mount Assembly
- HBU Bracket (Universal Projector Interface)
- Mounting Hardware Kit (various screws, washers, nuts)
- 사용 설명서(본 문서)
Image: The Chief VCMU Universal Projector Mount showing its main assembly and adjustable arms. This image illustrates the primary components included in the package.
설정 및 설치
This section outlines the steps for securely mounting your Chief VCMU projector mount.
1. 장착면을 준비합니다.
Identify a suitable mounting location. The surface must be structurally sound and capable of supporting the combined weight of the mount and projector (up to 250 lbs).
- For ceiling installations, locate ceiling joists or use appropriate anchors.
- For wall installations, ensure studs are located or use heavy-duty wall anchors.
2. Attach the HBU Bracket to the Projector
- Align the HBU bracket arms with the mounting holes on your projector.
- Use the appropriate screws from the hardware kit to secure the bracket to the projector. Ensure all screws are tightened evenly.
- Adjust the arms as necessary to achieve a balanced and secure fit.
3. Mount the VCMU Assembly
- Position the VCMU mount base on the prepared mounting surface.
- Mark the drilling locations through the mount's base plate.
- Drill pilot holes as required for your chosen fasteners.
- Secure the VCMU mount base to the surface using the appropriate heavy-duty fasteners. Ensure it is firmly attached and level.
4. Attach Projector to Mount
- Carefully lift the projector with the attached HBU bracket.
- Align the HBU bracket with the receiver on the VCMU mount.
- Slide the bracket into place until it locks securely.
- Engage any safety screws or locking mechanisms to prevent accidental disengagement.
운영 및 조정
Once installed, the Chief VCMU mount allows for precise adjustments to optimize your projector's image.
Pitch, Roll, and Yaw Adjustments
- 피치 조정: Loosen the pitch adjustment screws slightly. Tilt the projector up or down to achieve the desired vertical angle. Tighten screws to secure.
- Roll Adjustment: Loosen the roll adjustment screws. Rotate the projector left or right to level the image horizontally. Tighten screws to secure.
- Yaw Adjustment: The mount allows for rotation around the central axis. Loosen the yaw locking mechanism, rotate the projector to the desired horizontal position, and then re-tighten.
Always make small adjustments and re-tighten all screws to ensure stability after each adjustment.
유지
Regular maintenance ensures the longevity and safe operation of your Chief VCMU projector mount.
- 정기 검사: Annually inspect all mounting hardware and connections for tightness. Re-tighten any loose screws or bolts.
- 청소: 부드럽고 마른 천으로 마운트를 닦으세요. 마감재를 손상시킬 수 있는 연마성 세제나 용제는 사용하지 마세요.
- 중량 용량: Do not add additional weight to the mount beyond the projector's weight and the specified maximum capacity.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| Projector image is crooked. | Roll adjustment not properly set or screws loose. | Adjust the roll mechanism and ensure all screws are tightened. |
| Projector image is too high/low. | Pitch adjustment not properly set or screws loose. | Adjust the pitch mechanism and ensure all screws are tightened. |
| 산이 불안정하게 느껴집니다. | Mounting fasteners are loose or incorrect for the surface. | Verify all mounting fasteners are securely tightened. Ensure the mounting surface is adequate. If unsure, consult a professional installer. |
| Projector not securely attached to HBU bracket. | Incorrect screws used or not tightened. | Ensure correct screws are used and fully tightened to secure the projector to the HBU bracket. |
명세서
- 모델: VCMU
- 상표: 셰프
- 재료: 헤비 듀티 스틸
- 최대 중량 용량: 250파운드(113.4kg)
- 제품 크기: 17.01 x 9.25 x 3.82인치(43.2 x 23.5 x 9.7cm)
- 색상: 검은색
- 호환 장치: Universal Projectors
- 장착 유형: Universal (Ceiling/Wall adaptable with appropriate accessories, not included)
- 첫 번째 가능한 날짜: 14년 2012월 XNUMX일
- 제조업체: 셰프
- 원산지: 중국
보증 및 지원
For warranty information or technical assistance, please contact Chief customer support directly. Refer to the official Chief web구체적인 보증 조건과 연락처 정보는 해당 사이트나 구매 문서를 참조하세요.
제조업체: 셰프
Web대지: www.legrandav.com/products/chief (전amp(링크는 실제 링크와 다를 수 있습니다)
연락하다: 제조업체의 내용을 참조하세요 web최신 연락처 정보는 사이트에서 확인하세요.
