1. 서론
This manual provides comprehensive instructions for the installation, operation, and maintenance of the Akasa Lokstor M21 2 Bay 2.5" Mobile Rack (Model AK-IEN-03). This device allows you to install two 2.5-inch SATA Solid State Drives (SSDs) or Hard Disk Drives (HDDs) into a single standard 3.5-inch PC drive bay, offering convenient and tool-free access to your storage devices.
2. 제품 오버view
2.1 주요 특징
- Accommodates two 2.5" SATA SSDs/HDDs (up to 9.5mm height) in a single 3.5" PC drive bay.
- Tool-free design for easy installation and removal of 2.5" drives.
- 내구성 있는 스테인리스 스틸과 플라스틱 구조.
- Integrated security lock with key for drive protection.
- Supports SATA I, II, and III interfaces with transfer rates up to 6Gbps.
- Hot-swap functionality supported (requires compatible system configuration).
2.2개의 구성요소
The Akasa Lokstor M21 includes the mobile rack unit and necessary accessories for installation.
그림 1: 전면 view of the Akasa Lokstor M21 mobile rack, showing the two drive bays and eject mechanisms.
Figure 2: Diagram highlighting key features: (1) Steel structure, (2) Security lock with key, (3) Two 2.5" SATA SSD/HDD bays, (4) Tool-free HDD access mechanism.
3. 설정 및 설치
3.1 Installing the Mobile Rack into a PC Bay
- Ensure your computer is powered off and disconnected from the main power supply.
- Open your computer case to access the internal drive bays.
- Locate an available 3.5-inch drive bay. This is typically a bay designed for floppy drives or card readers.
- Slide the Akasa Lokstor M21 into the 3.5-inch bay from the front of the case until it is flush with the front panel.
- Secure the mobile rack using screws through the side mounting holes into the drive bay frame.
3.2 연결 케이블
- Connect the SATA data cables from the mobile rack's rear connectors to available SATA ports on your motherboard.
- Connect the SATA power cable from your power supply unit (PSU) to the mobile rack's power connector.
- 모든 연결이 안전한지 확인하세요.
그림 3: 후면 view of the mobile rack, illustrating the SATA data and power connections for the two drive bays.
3.3 Installing 2.5" SSD/HDD
- Ensure the security lock (if engaged) is in the unlocked position.
- Gently slide your 2.5-inch SSD or HDD into one of the available bays until it clicks securely into place. The tool-free mechanism will engage the drive's SATA connectors.
- Repeat for the second drive if desired.
Figure 4: A 2.5-inch drive being inserted or ejected from the mobile rack, showcasing the tool-free mechanism.
Note on Hot-Swapping: For hot-swapping functionality (inserting or removing drives while the system is running), ensure that AHCI mode is enabled in your computer's BIOS/UEFI settings for the SATA controller connected to the mobile rack. If AHCI is not enabled, drives may not be detected or may cause system instability when hot-swapped.
4. 사용 설명서
4.1 Drive Insertion and Removal
- 삽입하려면: Align the 2.5" drive with an empty bay and push it firmly until it locks into place.
- 제거하려면: Ensure the security lock is disengaged. Press the eject button or lever on the front of the bay to release the drive, then pull it out.
4.2 보안 잠금 사용
The Akasa Lokstor M21 features a key lock mechanism to secure your drives in place, preventing accidental removal or unauthorized access.
Figure 5: The security lock mechanism with the key inserted, demonstrating how to lock or unlock a drive bay.
- 잠그려면: Insert the provided key into the lock slot on the front of the desired drive bay and turn it to the locked position. This will prevent the drive from being ejected.
- 잠금 해제하려면: Insert the key and turn it to the unlocked position. The drive can now be ejected.
중요한: Always remove the key after locking or unlocking to prevent loss or damage.
5. 유지관리
- Keep the mobile rack clean and free from dust. Use a soft, dry cloth for cleaning.
- 장치를 극단적인 온도나 습도에 노출시키지 마십시오.
- 독한 화학 물질이나 연마성 세제를 사용하지 마십시오.
- Ensure proper airflow around the unit within your PC case to prevent overheating of installed drives.
6. 문제 해결
- 드라이브가 감지되지 않음:
- Check if the SATA data and power cables are securely connected to both the mobile rack and the motherboard/PSU.
- Ensure the 2.5" drive is fully inserted into the bay and locked into place.
- Verify that AHCI mode is enabled in your system's BIOS/UEFI settings for the SATA controller.
- Test the drive directly connected to the motherboard to rule out drive failure.
- Hot-swapping not working:
- Confirm AHCI mode is enabled in BIOS/UEFI.
- Ensure your operating system supports hot-swapping for SATA devices.
- Always safely eject drives through the operating system before physical removal.
- Drive difficult to insert/eject:
- Ensure the security lock is in the unlocked position.
- Verify the drive is correctly oriented and not obstructed.
- Do not force the drive; check for any foreign objects in the bay.
7. 사양
| 모델 번호 | AK-IEN-03 |
| 애플리케이션 | HDD mobile rack for 3.5" PC bay |
| 을 위해 설계되었습니다 | 2 x 2.5" SATA SSD/HDD (9.5 mm high) |
| 치수(길이 x 너비 x 높이) | 140 x 101.6 x 25mm(5.51 x 4 x 0.98인치) |
| 재료 | 스테인레스 스틸 및 플라스틱 |
| SATA Compatibility | SATA I / II / III |
| 인터페이스 | SATA |
| 전송 속도 | Up to 6Gbps (SATA III) |
| Hot Swap Support | Yes (requires AHCI enabled) |
| 호환 장치 | 데스크탑 PC |
| 품목 무게 | 0.32 온스(약 9그램) |
8. 보증 및 지원
8.1 보증 정보
Specific warranty terms for the Akasa Lokstor M21 (AK-IEN-03) may vary by region and retailer. Please refer to the warranty information provided at the point of purchase or visit the official Akasa web자세한 보증 정책은 해당 사이트를 참조하십시오.
8.2 기술 지원
For technical assistance, troubleshooting beyond the scope of this manual, or inquiries regarding your Akasa product, please visit the official Akasa support website or contact their customer service department. Contact information can typically be found on the Akasa web대지:
