소개
This manual provides comprehensive instructions for the safe and efficient operation, adjustment, and maintenance of the Ford Model P Series 131 3-Bar Pull Type Chisel Plow. Adhering to the guidelines within this document will help ensure optimal performance, extend the lifespan of your equipment, and promote operator safety. Please read this manual thoroughly before attempting to set up, operate, or service the chisel plow.
Figure 1: Cover of the Ford Model P Series 131 3-Bar Pull Type Chisel Plow Operators Manual. This image displays the front cover of the official operator's manual, which contains detailed instructions for the equipment.
설정 및 조립
Proper setup is crucial for the safe and effective operation of your chisel plow. Follow these steps carefully:
- 포장 풀기 및 검사: 포장에서 모든 구성품을 조심스럽게 꺼내십시오. 배송 중 파손 여부를 확인하십시오. 파손이 발견되면 즉시 판매점에 보고하십시오.
- 트랙터에 부착: Ensure the tractor's drawbar is compatible with the plow's hitch. Securely attach the plow to the tractor's drawbar using the appropriate hitch pin and safety clip. Verify all connections are tight.
- 유압 연결: Connect the plow's hydraulic hoses to the tractor's hydraulic outlets. Ensure connections are clean and free of debris. Check for proper fluid levels in the tractor's hydraulic system.
- 깊이 조정: Adjust the plow's depth control mechanism according to the desired tilling depth. Refer to the specific instructions for your model's depth adjustment system.
- Tine Installation (if applicable): If tines are not pre-installed, attach them securely to the plow frame using the specified hardware. Ensure proper spacing and orientation.
작동 지침
Before operating, ensure all safety checks are complete and you are familiar with the tractor and plow controls.
- 수술 전 체크리스트:
- Check tire pressure on both tractor and plow.
- Verify all bolts and fasteners are tight.
- Ensure hydraulic hoses are free from leaks and properly connected.
- Confirm all safety shields and guards are in place.
- 쟁기질하기: Slowly lower the plow into the soil using the tractor's hydraulic controls. Begin tilling at a moderate speed, gradually increasing as conditions allow.
- Adjusting Depth and Speed: Monitor the tilling depth and adjust as needed. Optimal operating speed will vary based on soil type, moisture content, and desired results. Avoid excessive speed which can lead to poor tilling and increased wear.
- 선회: When turning at the end of a pass, raise the plow completely out of the ground to prevent damage to the tines and frame.
- 연결 해제: When finished, raise the plow completely, disengage the tractor's PTO (if applicable), and park the equipment on a level surface.
유지
Regular maintenance is essential for the longevity and reliable performance of your chisel plow.
- 일일 점검:
- Inspect tines for wear or damage. Replace worn tines promptly.
- Check for loose bolts and tighten as necessary.
- Clean soil and debris from the plow frame.
- Weekly/50-Hour Maintenance:
- Lubricate all grease points as indicated in the lubrication chart (refer to the full manual for details).
- Inspect hydraulic hoses and fittings for leaks or damage.
- 타이어의 압력과 상태를 확인하세요.
- Seasonal/Annual Maintenance:
- Thoroughly clean and inspect the entire plow.
- Repaint any areas where paint is chipped to prevent rust.
- Store in a dry, protected area during off-season.
문제 해결
이 섹션에서는 운영 중에 발생할 수 있는 일반적인 문제에 대해 설명합니다.
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| Plow not penetrating soil | Incorrect depth setting, worn tines, hard soil conditions | Adjust depth, replace tines, increase down pressure (if applicable) |
| Uneven tilling depth | Uneven ground, improper leveling, tire pressure differences | Level plow, check tire pressure, adjust hitch |
| 과도한 진동/소음 | Loose components, damaged tines, worn bearings | Inspect and tighten all fasteners, replace damaged parts, check bearings |
명세서
The following are general specifications for the Ford Model P Series 131 3-Bar Pull Type Chisel Plow. Specific details may vary slightly by production year.
- 모델: P Series 131
- 유형: 3-Bar Pull Type Chisel Plow
- Number of Tines: Typically 7 to 13 (variable based on configuration)
- 작업 폭 : Approximately 8 to 15 feet (variable)
- 작업 깊이 : Up to 12 inches (adjustable)
- 히치 유형: 견인 바
- Hydraulic Requirements: Single or double-acting remote cylinder
- 대략적인 무게 : 1,000 - 2,000 lbs (variable by configuration)