소개
Thank you for choosing the STEINEL HS 152 XENO Sensor Halogen Floodlight. This product is designed to provide efficient and reliable outdoor lighting with integrated motion detection for enhanced security and convenience. Please read this manual carefully to ensure proper installation, operation, and maintenance of your floodlight.
Image: STEINEL HS 152 XENO Sensor Halogen Floodlight. This image shows the floodlight from a front-side angle, highlighting its compact design and the integrated motion sensor below the lamp 주택.
안전 지침
WARNING: Risk of electric shock! Installation requires knowledge of electrical systems. Incorrect installation can lead to fire or electric shock. For your safety, always consult a qualified electrician if you have any doubts.
- Disconnect power at the main fuse or circuit breaker before installation or maintenance.
- 공급 볼륨을 확인tage matches the floodlight's requirements (230-240V).
- Do not open the product housing unless specified in this manual.
- 어떤 식으로든 제품을 변형하지 마십시오.
- 어린이가 포장재에 접근하지 못하도록 하십시오.
- The floodlight becomes hot during operation. Avoid touching the lamp or housing immediately after use.
- 현지 전기 규정에 따라 적절한 접지를 확보하십시오.
- This product is rated IP44 for protection against splashing water. Do not immerse in water.
패키지 내용
모든 부품이 있는지, 손상되지 않았는지 확인해 주십시오.
- 1x STEINEL HS 152 XENO Sensor Halogen Floodlight (with integrated R7s 150W halogen lamp)
- 1x Set of mounting screws and wall plugs
- 1x Set of cover plates for detection range adjustment
- 1x 사용 설명서
설치
- 준비: Turn off the power supply at the main circuit breaker. Use a voltage tester to ensure the circuit is de-energized.
- 장착 위치: Choose a suitable mounting location, ideally 1.8m to 2.5m above the ground, where the sensor has an unobstructed view of the desired detection area. Avoid mounting near heat sources or objects that might cause false triggers (e.g., moving branches, busy roads).
- 교련: Mark the drilling points using the floodlight's mounting plate as a template. Drill holes and insert wall plugs.
- 배선: Connect the electrical wires (Live, Neutral, Earth) from your mains supply to the corresponding terminals inside the floodlight's wiring compartment. Ensure all connections are secure.
- Mounting the Floodlight: Secure the floodlight to the wall using the provided screws. Adjust the floodlight head to the desired angle.
- 전원 켜기: Restore power at the main circuit breaker. The floodlight will perform a brief self-test.
작업
The STEINEL HS 152 XENO floodlight features an integrated passive infrared (PIR) motion sensor. When motion is detected within its adjustable range and the ambient light level falls below the set twilight threshold, the floodlight will automatically switch on for the pre-set duration.
센서 조정
The sensor has three main adjustment controls, typically located on the underside of the sensor head:
- Range (Reach): Adjusts the detection distance, up to 12 meters, limitable to approximately 5 meters using the included cover plates. Turn the dial to increase or decrease the range.
- Twilight Threshold (Lux): Sets the ambient light level at which the sensor becomes active. Turn towards the sun symbol for daylight operation (test mode) or towards the moon symbol for activation only in darkness.
- Time Setting (Time): Determines how long the light remains on after motion is detected. Adjust the dial to set the desired duration.
The detection angle is 180° with an opening angle of 90°. Use the provided cover plates to precisely mask out areas you do not wish to be detected, such as public pathways or neighboring properties.
유지
청소
Clean the floodlight and sensor lens regularly with a soft, damp cloth. Do not use abrasive cleaners or solvents, as these can damage the surfaces or the sensor lens.
Lamp 대사
WARNING: Disconnect power before replacing the lamp.
- Ensure the floodlight is cool before handling.
- 조심스럽게 열어보세요.amp 주택.
- Remove the old R7s halogen lamp.
- Insert a new R7s 150W halogen lamp. Ensure it is correctly seated.
- 닫기amp housing securely.
- 전원을 복구합니다.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 조명이 켜지지 않습니다. | 전원 공급이 없습니다. Lamp 불완전한. Twilight threshold set too high (daylight). Sensor range too low. | 회로 차단기를 확인하십시오. l을 교체하세요amp. Adjust twilight setting towards 'moon' symbol. Increase sensor range. |
| 표시등이 계속 켜져 있습니다. | 감지 영역 내에서 지속적인 움직임이 관찰됩니다. 센서에 결함이 있습니다. | Adjust sensor range or mask detection area. 고객 지원팀에 문의하세요. |
| 움직임이 없는데도 불이 켜집니다. | False triggers (e.g., heat sources, small animals, moving branches). | Adjust sensor angle, reduce range, or use cover plates to mask problematic areas. |
명세서
| 상표: | 슈타이넬 |
| 모델 번호: | 632113 |
| 색상: | 검은색 (Note: Product title indicates 'ws' for white, but specifications list 'Noir' for black.) |
| 특징: | 동작 탐지기 |
| 재료: | 유리 |
| 전원: | 코드식 전기 |
| 광원 유형: | 할로겐 |
| 광원 수: | 1 |
| 권tage: | 230 볼트 |
| 왓tage: | 150 와트 |
| 보호 등급: | IP44 |
| 감지 각도: | 180° (Opening angle 90°) |
| 최대. 감지 범위: | 12미터 (5미터까지 조절 가능) |
보증 및 지원
For warranty information and technical support, please refer to the official STEINEL website or contact your local STEINEL distributor. Keep your purchase receipt as proof of purchase.
STEINEL Contact Information:
- Official STEINEL Web대지
- Refer to product packaging for specific regional support contacts.
