SkyTech SKY-5301 벽난로 리모컨 및 온도 조절기 사용 설명서

1. 서론

The SkyTech SKY-5301 remote control system provides a safe, reliable, and user-friendly method for operating gas heating appliances. This system allows for both thermostatic and manual control directly from the handheld transmitter. It operates using radio frequencies (RF) within a 20-foot range, utilizing non-directional signals. The system is pre-programmed with one of 1,048,567 security codes at the factory. For initial use, the remote receiver's code must be matched to the transmitter's code.

2. 안전 정보

• 설치 및 작동 전에 모든 지침을 주의 깊게 읽으십시오.
• This system is designed for use with millivolt gas valves only. The receiver acts as a dry contact switch and will not output any voltage.
• 모든 배선 작업은 자격을 갖춘 기술자가 수행하고 지역 규정을 준수해야 합니다.
• Do not expose the transmitter or receiver to water or extreme temperatures.
• 배터리 부족 표시등이 켜지면 즉시 배터리를 교체하여 정상적인 작동을 보장하십시오.
• 어린이의 손이 닿지 않는 곳에 보관하세요.

3. 패키지 내용

패키지에 모든 구성품이 들어 있는지 확인하세요.

• Handheld Transmitter (with LCD display)
• Receiver Box (wall plate mounted)
• Wall Plate (for receiver mounting)
• 설치 지침
• Batteries (4 AA batteries for transmitter and receiver)

4. 구성 요소 이상view

The SkyTech SKY-5301 system consists of a handheld transmitter and a wall-mounted receiver unit. Understanding each component is essential for proper setup and operation.

이미지 1: 위에view of the SkyTech SKY-5301 system, showing the handheld transmitter with its backlit LCD screen displaying temperature and time, and the wall-mounted receiver with its ON/REMOTE/OFF slider switch and LEARN button.

4.1. Handheld Transmitter

• LCD 디스플레이: Shows room temperature, set temperature, 24-hour clock, and a 9-hour countdown timer. Features a backlight for visibility.
• 버튼: Three buttons (Up, Mode, Down) for navigation and setting adjustments.
• 기능: Allows for manual or thermostatic control of the fireplace.

4.2. Wall-Mounted Receiver

• 슬라이더 스위치: Features ON, REMOTE, and OFF positions for direct control or remote operation.
• 학습 버튼: Used to synchronize the receiver with the transmitter.
• 힘: Battery-powered for reliable operation.
• 호환성: Designed exclusively for millivolt gas valves, acting as a dry contact switch. It does not output voltage.

5. 설정

5.1. 배터리 설치

Install the included AA batteries into both the transmitter and the receiver unit.

1. 송신기: Open the battery compartment on the back of the handheld transmitter. Insert the batteries, observing the correct polarity (+/-). Close the compartment.
2. 수화기: Remove the wall plate cover. Open the battery compartment on the receiver unit. Insert the batteries, observing the correct polarity (+/-). Close the compartment.

5.2. 수신기 배선

The receiver unit must be wired to your fireplace's millivolt gas valve. This process typically involves connecting two wires from the receiver to the appropriate terminals on the gas valve. Ensure the fireplace's gas supply is turned OFF before proceeding with any wiring.

1. Locate the millivolt gas valve on your fireplace.
2. Identify the two terminals designated for remote control or thermostat connection. These are typically labeled TH and TH/TP or similar.
3. Connect the two wires from the receiver unit to these terminals. The polarity of these wires usually does not matter for a dry contact switch.
4. 연결을 보호합니다.

5.3. 수신기 장착

After wiring, mount the receiver unit to the wall using the provided wall plate and hardware. Ensure it is in a location where it can receive signals from the transmitter, ideally within 20 feet and not obstructed by large metal objects.

5.4. Pairing the Transmitter and Receiver (Learning Function)

The transmitter and receiver must be paired to communicate. This process is called the "learning function."

1. Ensure batteries are installed in both units.
2. On the receiver unit, slide the ON/REMOTE/OFF switch to the 원격 위치.
3. 를 누르고 계세요 배우다 button on the receiver for approximately 3 seconds until you hear a short beep.
4. Within 20 seconds of the beep, press any button on the handheld transmitter.
5. The receiver will emit a series of beeps, confirming that the transmitter and receiver are now paired.
6. Test the connection by pressing the "Up" or "Down" button on the transmitter to see if the fireplace responds.

6. 운영

6.1. Transmitter Display and Controls

The backlit LCD on the transmitter provides essential information and allows for easy control.

• 표시 정보 :
  • 현재 실내 온도
  • 온도 설정
  • 24시간제
  • 9 시간 카운트 다운 타이머
  • 배터리 수준 표시기
• 버튼:
  • 위쪽(▲): Increases set temperature, adjusts time/timer up.
  • 모드/설정: Cycles through operating modes, enters setting menus.
  • 아래로 (▼): Decreases set temperature, adjusts time/timer down.

6.2. 작동 모드

The system supports two primary operating modes:

• 수동 모드: The fireplace turns ON or OFF directly when commanded by the transmitter, regardless of temperature.
• 온도 조절 모드: The fireplace will turn ON or OFF automatically to maintain the set temperature.

6.3. 설정 온도

1. 를 누르세요 모드/설정 button until the display shows the desired operating mode (e.g., "THERMO").
2. 사용하세요 업(▲) or 아래로 (▼) buttons to adjust the set temperature to your desired level. The display will show the set temperature.
3. The system will automatically maintain this temperature in thermostatic mode.

6.4. 타이머 설정

The 9-hour countdown timer can be used to automatically turn off the fireplace after a set duration.

1. 를 누르세요 모드/설정 button until the display shows "TIMER".
2. 사용하세요 업(▲) or 아래로 (▼) buttons to set the desired countdown duration (up to 9 hours).
3. Once set, the timer will begin counting down. The fireplace will turn off when the timer reaches zero.

7. 유지관리

7.1. 배터리 교체

When the low battery indicator appears on the transmitter's LCD, or if the system becomes unresponsive, replace the batteries in both the transmitter and receiver with fresh AA batteries. Always replace all batteries at the same time.

7.2. 청소

Wipe the transmitter and receiver surfaces with a soft, dry cloth. Do not use abrasive cleaners or immerse the units in water.

8. 문제 해결

9. 사양

10. 보증 및 지원

For warranty information or technical support, please refer to the contact details provided with your product packaging or visit the official SkyTech web대지. 보증 청구를 위해 구매 영수증을 보관하십시오.