메트렐 MI 2093 라인 검출기 사용자 설명서

1. 서론

This user manual provides comprehensive instructions for the safe and efficient operation of the Metrel MI 2093 Line Detector. Please read this manual thoroughly before using the device to ensure proper functionality and to prevent potential hazards. Keep this manual for future reference.

2. 안전 정보

부상이나 장치 손상을 방지하려면 항상 다음 안전 지침을 준수하세요.

• Do not use the device if it appears damaged or if any part of the casing가 열려있습니다.
• Ensure that the test leads are in good condition and free from cuts or abrasions.
• Always disconnect the device from the circuit before changing batteries or performing maintenance.
• 장치를 극한의 온도, 습도 또는 직사광선에 노출시키지 마십시오.
• Refer to local electrical safety regulations and standards when performing measurements.

3. 패키지 내용

Verify that all items listed below are present in your Metrel MI 2093 Line Detector package:

• Metrel MI 2093 Line Detector (main unit)
• 수신기 유닛
• Set of test leads (various types including probes and alligator clips)
• Carrying case (blue)
• 사용 설명서 및 문서

The image displays the complete Metrel MI 2093 Line Detector kit. It includes the main line detector unit, a smaller receiver unit, various test leads with different connectors (probes, alligator clips), and a blue carrying case. Instruction manuals and documentation are also visible.

4. 설정

4.1 배터리 설치

The Metrel MI 2093 Line Detector requires batteries for operation. Locate the battery compartment on the back of both the main unit and the receiver. Insert the specified battery type (refer to the battery compartment label for details), ensuring correct polarity. Close the battery compartment securely.

4.2 테스트 리드 연결

Connect the appropriate test leads to the main unit based on the type of measurement you intend to perform. Ensure a firm and secure connection to prevent inaccurate readings or disconnections during use.

5. 사용 설명서

5.1 전원 켜기/끄기

To power on the device, press and hold the power button located on the main unit and the receiver until the display illuminates. To power off, press and hold the power button again until the display turns off.

5.2 Line Detection Procedure

1. Ensure the circuit to be tested is de-energized if required for safety or specific test procedures.
2. Connect the main unit to the circuit or cable you wish to trace using the appropriate test leads.
3. 수신기를 켜세요.
4. Move the receiver along the path of the cable. The receiver will indicate the presence of the signal emitted by the main unit, allowing you to trace the line.
5. Observe the signal strength indicator on the receiver to pinpoint the exact location of the line.

6. 유지관리

6.1 청소

Clean the device regularly with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these may damage the casing or display. Ensure the device is powered off before cleaning.

6.2 배터리 교체

Replace batteries when the low battery indicator appears on the display. Always use new batteries of the specified type. Dispose of old batteries according to local regulations.

6.3 보관

When not in use, store the Metrel MI 2093 Line Detector in its carrying case in a cool, dry place, away from direct sunlight and extreme temperatures. Remove batteries if storing for extended periods to prevent leakage.

7. 문제 해결

If you encounter issues with your Metrel MI 2093 Line Detector, refer to the following common problems and solutions:

• 기기의 전원이 켜지지 않습니다: 배터리 설치를 확인하고 배터리가 완전히 방전되지 않았는지 확인하세요. 필요하면 교체하세요.
• 부정확한 판독값: Ensure test leads are securely connected and in good condition. Verify that the device is being used according to the operating instructions for the specific application.
• 신호가 감지되지 않았습니다. Confirm that the main unit is powered on and correctly connected to the line. Ensure the receiver is within range and powered on.

If the problem persists after attempting these solutions, contact Metrel customer support.

8. 사양

9. 보증 및 지원

The Metrel MI 2093 Line Detector typically comes with a manufacturer's warranty. Please refer to the warranty card included in your package for specific terms and conditions. Spare parts availability is generally supported for 1 year from the date of purchase.

For technical support, service, or warranty claims, please contact Metrel customer service through their official web사이트 또는 제품 설명서에 제공된 연락처 정보를 참조하세요.