소개
This manual provides essential instructions for the proper setup, operation, and maintenance of your Intermec SR30 Linear Imager RS232 Barcode Scanner. Please read this manual thoroughly before using the device to ensure optimal performance and to prevent damage.
The Intermec SR30 is a high-performance linear imager designed for reliable barcode scanning in various environments, connecting via an RS232 interface.
안전 정보
- 스캐너를 극한의 온도, 습도 또는 직사광선에 노출시키지 마세요.
- 스캐너를 떨어뜨리거나 심한 충격을 주지 마세요.
- 스캐너를 열거나 개조하지 마십시오. 모든 서비스는 자격을 갖춘 전문가에게 맡기십시오.
- Use only the power supply and cables provided or approved by Intermec.
- 바코드를 정확하게 판독하려면 스캔 창을 깨끗하게 유지하십시오.
패키지 내용
패키지에 다음 품목이 포함되어 있는지 확인하십시오.
- Intermec SR30 Linear Imager Barcode Scanner
- RS232 Interface Cable
- 전원 공급 장치
- 문서 (본 설명서 또는 유사한 설명서)
누락되거나 손상된 품목이 있는 경우 즉시 공급업체에 문의하십시오.
설정
1. 스캐너 연결
- Connect the RS232 Cable: Plug the RS232 connector of the interface cable into the corresponding serial port on your host computer or POS system.
- 스캐너에 연결: Plug the other end of the interface cable into the port at the base of the SR30 scanner. Ensure a secure connection.
- 전원 공급 장치 연결: Connect the power supply unit to the power port on the interface cable or directly to the scanner base, as applicable for your specific cable configuration. Plug the power supply into a standard electrical outlet.
2. 초기 전원 켜기
Once connected, the scanner should power on automatically. Observe the indicator lights (typically an LED) for initial status. The scanner may emit a short beep to indicate it is ready for operation.
3. Basic Configuration (if required)
The SR30 scanner may require configuration for specific RS232 communication parameters (e.g., baud rate, data bits, parity) to match your host system. Refer to the detailed programming guide (often a separate document with programming barcodes) for advanced configuration. For basic operation, the default settings are often sufficient.
스캐너 작동
1. 바코드 스캐닝
- 목표: Point the scanning window of the SR30 at the barcode you wish to read. Ensure the entire barcode is within the scanner's field of view.
- 주사: Press and hold the trigger button (if applicable) or present the barcode to the scanner's window for automatic scanning.
- 확인: A successful scan is typically indicated by an audible beep and/or a change in the LED indicator light (e.g., green light). The barcode data will be transmitted to your host system.
2. 지표 이해하기
- 녹색 LED : Indicates a successful barcode read.
- Red/Amber LED: May indicate an error, scanner busy, or awaiting input. Consult the full programming guide for specific error codes or patterns.
- Beep Sounds: Different beep patterns can indicate successful reads, errors, or configuration changes.
유지
스캐너 청소
- Regularly clean the scanning window with a soft, lint-free cloth damp물이나 부드럽고 연마성이 없는 세척제로 세척하세요.
- Do not use harsh chemicals, solvents, or abrasive materials, as these can damage the scanner's surface.
- 청소하기 전에 스캐너의 전원이 꺼져 있는지 확인하십시오.
저장
사용하지 않을 때는 스캐너를 직사광선과 극한 온도 변화를 피해 깨끗하고 건조한 곳에 보관하십시오.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 스캐너의 전원이 켜지지 않습니다. | Power cable not connected; power outlet faulty; power supply unit failure. | Check all cable connections. Try a different power outlet. Ensure the power supply is functioning. |
| 스캐너가 바코드를 읽지 못합니다. | Barcode damaged or poorly printed; scanning window dirty; incorrect symbology enabled; scanner not configured for host. | Ensure barcode is clear. Clean scanning window. Verify scanner configuration matches host system requirements. Try scanning a known good barcode. |
| Barcode data not appearing on host. | RS232 cable loose or faulty; incorrect RS232 communication settings (baud rate, parity); host application not ready. | Check RS232 cable connection. Verify RS232 settings on both scanner and host. Ensure host application is active and ready to receive input. |
명세서
- 모델: SR30
- 부품 번호: 225-727-003 (Kit)
- 스캐너 유형 : 선형 이미저
- 인터페이스: RS232
- 제조업체: 인터멕
- 품목 무게: 0.01 ounces (approximate, scanner only)
- 부서: 바코드
- ASIN: B003T0WF3S
보증 및 지원
For warranty information and technical support, please refer to the documentation provided with your purchase or visit the official Intermec web사이트. 보증 청구를 위해 구매 증빙 자료로 구매 영수증을 보관하세요.
Contact your reseller or Intermec customer service for assistance with issues not covered in this manual.
