1. 제품 오버view
The Swanstone SS-3460-168 Solid Surface Center Drain Shower Base is an American-made, high-performing surfacing solution designed for bath and kitchen applications. Manufactured from compression-molded materials, this shower base is non-porous, highly durable, and resistant to mold and mildew. It is engineered for superior impact strength, heat resistance, and long-term durability, ensuring a lifetime of value and easy maintenance.
주요 특징:
- Reinforced Solid Surface: Color and texture run throughout the material, preventing wear.
- Single Threshold Design: Ideal for specific shower enclosure configurations.
- Pre-installed Fit-Flo Drain: Simplifies and reduces installation time.
- Non-Porous Material: Resists mold, mildew, and is easy to clean.
- Pebbled, Slip-Resistant Surface: Enhances safety during use.
그림 1: 상단 view of the Swanstone SS-3460-168 Shower Base, showing the central drain and pebbled surface in Baby's Breath color.
2. 설정 및 설치
Proper installation is crucial for the longevity and performance of your Swanstone shower base. It is highly recommended that installation be performed by a qualified professional. Always consult local building codes and plumbing regulations before beginning installation.
설치 단계(일반 지침):
- 바닥재 준비: Ensure the subfloor is level, clean, and structurally sound. Any unevenness must be corrected prior to installation.
- 드라이핏: Place the shower base in its intended position to verify fit and drain alignment. Mark the perimeter of the base on the subfloor.
- Mortar Bed Preparation: A mortar bed is required to provide full support for the shower base and prevent flexing. Mix a suitable mortar according to manufacturer instructions and apply it evenly within the marked perimeter.
- 기초를 다지세요: Carefully set the shower base into the wet mortar bed, ensuring the pre-installed Fit-Flo drain aligns with the plumbing. Apply firm, even pressure to ensure full contact with the mortar.
- 수준 측량: Use a level to confirm the shower base is perfectly level in all directions. Adjust as necessary while the mortar is still workable.
- 드레인 연결: Connect the shower drain to the existing plumbing system, ensuring all connections are watertight.
- 경화 시간: Allow the mortar to cure completely as per the mortar manufacturer's recommendations before proceeding with wall installation or using the shower.
- 밀봉: Apply appropriate sealant around the perimeter of the shower base where it meets the wall and floor, as required.
Note: Detailed installation instructions may vary. Always refer to the specific installation guide provided with your product packaging for precise steps and safety precautions.
3. 운영
The Swanstone Solid Surface Shower Base is designed for standard showering use. Once properly installed and sealed, it provides a durable and safe surface for your daily shower routine. The pebbled surface offers enhanced slip resistance for user safety.
Ensure the drain is clear of debris to maintain proper water flow and prevent pooling. Regular cleaning, as outlined in the Maintenance section, will ensure optimal performance and appearance.
4. 관리 및 유지 보수
Maintaining your Swanstone shower base is simple due to its non-porous, solid surface material. Regular cleaning will preserve its appearance and hygiene.
일반 청소:
- For routine cleaning, use a soft cloth or sponge with warm water and a mild, non-abrasive liquid cleaner.
- Rinse thoroughly with water after cleaning to remove all cleaner residue.
- Wipe the surface dry to prevent water spots and mineral buildup.
얼룩 제거:
- For stubborn stains, a mild abrasive cleaner (e.g., Soft Scrub with Bleach) or a paste of baking soda and water can be used. Apply with a soft cloth and rub gently.
- For hard water spots or mineral deposits, use a solution of white vinegar and water. Allow it to sit for a few minutes before scrubbing and rinsing.
- Avoid using harsh chemicals, strong acids, or abrasive pads, as these can damage the surface finish.
예방 조치:
- Rinse the shower base after each use to wash away soap scum and residue.
- Ensure adequate ventilation in the bathroom to prevent mold and mildew growth.
- Do not place extremely hot items directly on the surface.
5. 문제 해결
This section addresses common issues you might encounter with your shower base and provides potential solutions.
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| Slow Drainage / Water Pooling |
|
|
| 표면 얼룩 |
|
|
| 배수구에서 불쾌한 냄새가 납니다 |
|
|
If you encounter an issue not listed here or if the suggested solutions do not resolve the problem, please contact Swanstone Customer Support.
6. 제품 사양
| 기인하다 | 세부 사항 |
|---|---|
| 모델 번호 | SS-3460-168 |
| 제조업체 | 스완스톤 |
| 치수(길이 x 너비 x 높이) | 60-in L x 34-in H x 5.5-in H (Note: Product dimensions from source seem to be shipping package dimensions, using variant dimensions for actual product size.) |
| 색상 | Baby's Breath |
| 재료 | 솔리드 표면 |
| 배수 위치 | 중앙드레인 |
| 품목 무게 | Approximately 155 pounds (참고: 고객 재views suggest actual product weight is significantly less, closer to 25-30 lbs, with shipping weight including crating.) |
| 포함된 구성 요소 | Shower Base (with pre-installed Fit-Flo drain) |
7. 보증 정보
The Swanstone SS-3460-168 Solid Surface Center Drain Shower Base is backed by a 제한된 평생 보증. 이 보증은 정상적인 사용 및 서비스 과정에서 발생하는 재료 및 제조상의 결함을 보장합니다.
For complete details regarding warranty coverage, terms, conditions, and how to make a claim, please refer to the official warranty document included with your product packaging or visit the official Swanstone web사이트. 보증 확인을 위해 구매 증빙 자료를 보관하세요.
8. 고객 지원
Should you have any questions, require technical assistance, or need to report an issue with your Swanstone shower base, please contact Swanstone Customer Support.
- 온라인 리소스: Visit the official Swanstone website for FAQs, product information, and additional support materials.
- 제조업체에 문의: Refer to your product packaging or the Swanstone web직접 연락 정보(전화번호, 이메일)를 위한 사이트입니다.
- 판매자 지원: If purchased through a retailer like Amazon, you may also contact the seller (Bath1 in this case) for order-specific inquiries.
For more information about Swanstone products, you can visit the Swanstone Store on Amazon.
