1. 소개 및 이상view
The HP StorageWorks 60 Modular Smart Array (MSA60) is a 2U rack-mountable Serial Attached SCSI (SAS) disk drive array designed to support 3.5-inch Serial ATA (SATA) drives. This system provides a robust and scalable storage solution, offering data performance, availability, and storage density for various computing environments. This manual provides essential information for the proper installation, configuration, operation, and maintenance of your MSA60 unit.
그림 1: 앞쪽 view of the Hewlett Packard MSA60 Modular Smart Array. This image displays the front panel of the HP MSA60, featuring twelve 3.5-inch drive bays arranged in four columns of three. Each bay includes an indicator light, suggesting drive activity or status. The overall design is a standard rack-mountable 2U form factor.
2. 안전 정보
Please read all safety instructions carefully before installing or operating the MSA60. Failure to follow these instructions may result in electric shock, fire, or damage to the equipment.
- Ensure the power supply is disconnected before performing any maintenance or installation procedures.
- Only use the power cords and adapters supplied or approved by Hewlett Packard.
- Install the unit in a well-ventilated area to prevent overheating.
- 본 제품을 습기나 극한의 온도에 노출시키지 마십시오.
- Heavy equipment: Use proper lifting techniques or assistance when moving the unit.
3. 패키지 내용
Verify that all components are present and undamaged upon unpacking. Contact your vendor immediately if any items are missing or damaged.
- HP MSA60 Modular Smart Array unit
- 랙 장착 키트
- Power cords (quantity may vary by region)
- SAS cables
- 문서(빠른 시작 가이드, 보증 정보)
- Optional: 3.5-inch SATA hard drives (if purchased with the unit)
4. 설정
4.1 랙 설치
- Attach the rack rails to the rack cabinet according to the instructions provided with the rack mounting kit.
- Carefully slide the MSA60 unit onto the installed rails until it clicks into place.
- Secure the unit to the rack using the provided screws.
4.2 드라이브 설치
- Ensure the MSA60 is powered off and disconnected from power sources.
- Insert each 3.5-inch SATA hard drive into an available drive bay. Ensure the drive is fully seated and the latch mechanism engages.
- 원하는 모든 드라이브에 대해 이 과정을 반복하십시오.
4.3 케이블링
- Connect the SAS cables from the MSA60 to the appropriate SAS controller ports on your server or host system.
- Connect the power cords to the MSA60 power supply units and then to a grounded power outlet.
5. 사용 설명서
5.1 전원 켜기
After all connections are secure, power on the MSA60 by ensuring the power outlets are active. The unit will typically power on automatically. Observe the indicator lights on the front panel for system status.
5.2 초기 구성
The MSA60 is managed through the SAS controller in your host server. Refer to your SAS controller's documentation for instructions on how to detect the array, configure logical drives (RAID levels), and allocate storage.
5.3개의 드라이브 상태 표시기
- 녹색(단색): Drive is active and operating normally.
- 녹색(깜박임): Drive activity (reading/writing data).
- 앰버(단색): Drive fault or predictive failure.
- 끄다: Drive is not present or not powered.
6. 유지관리
6.1 정기점검
- 모든 케이블 연결을 주기적으로 점검하여 안전한지 확인하세요.
- Monitor the status indicator lights on the front panel for any anomalies.
- 과열을 방지하기 위해 장치 주변에 적절한 공기 흐름을 확보하세요.
6.2 드라이브 교체
In the event of a drive failure (indicated by an amber light), replace the faulty drive with a new, compatible 3.5-inch SATA drive. Consult your SAS controller documentation for specific hot-swap procedures if applicable.
7. 문제 해결
7.1 일반적인 문제 및 해결 방법
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 장치의 전원이 켜지지 않음 | Power cords disconnected; Power supply failure | Check power cord connections; Test power outlets; Contact support if power supply is faulty. |
| Drives not detected by host | SAS cables disconnected; SAS controller issue; Incorrect configuration | Verify SAS cable connections; Check SAS controller status; Review SAS controller documentation for configuration. |
| Amber light on drive | Drive failure or predictive failure | Replace the faulty drive. Back up data if possible before replacement. |
| 과열 | Poor ventilation; Fan failure | Ensure proper airflow in the rack; Check fan operation; Clean dust from vents. |
8. 사양
| 특징 | 세부 사항 |
|---|---|
| 제품 모델 번호 | AJ924A |
| 상표 | 휴렛팩커드 |
| 폼 팩터 | 2U 랙 장착 가능 |
| 드라이브 베이 | 12 x 3.5인치 |
| Supported Drive Interface | Serial ATA (SATA) |
| 호스트 인터페이스 | 직렬 연결 SCSI(SAS) |
| Digital Storage Capacity (Max) | 12 TB (with 1TB drives, actual capacity depends on drives installed) |
| 제품 치수 | 4.13 x 2.35 x 3.85인치(10.49 x 5.97 x 9.78cm) |
| 품목 무게 | 120파운드(54.43kg) |
| 제조업체 | HP |
| ASIN | B001F4R2F6 |
| 한국어: | 884420366867 |
9. 보증 및 지원
For detailed warranty information, please refer to the warranty document included with your product or visit the official Hewlett Packard support website. Technical support and service options are available through Hewlett Packard's customer service channels. Please have your product model number (AJ924A) and serial number ready when contacting support.
