매뉴얼+

Pentair PLM200

Pentair Sta-Rite PLM200 System:2 Modular Media Pool Filter Instruction Manual

모델: PLM200

1. 서론

This manual provides essential instructions for the safe installation, operation, and maintenance of your Pentair Sta-Rite PLM200 System:2 Modular Media Pool Filter. Please read this manual thoroughly before attempting to install or operate the filter. Retain this manual for future reference.

The Sta-Rite PLM200 System:2 Modular Media Pool Filter is designed for efficient filtration in aboveground pools, inground pools, and hot tubs. Its durable two-piece tank housing, constructed of rugged ABS thermoplastic, ensures a long service life. The unique posi-ring closure allows for safe and fast access to the tank internals for maintenance.

Pentair Sta-Rite PLM200 System:2 Modular Media Pool Filter

그림 1.1: Pentair Sta-Rite PLM200 System:2 Modular Media Pool Filter. This image shows the complete filter unit, highlighting its compact design and robust construction.

2. 안전 정보

경고: 이 지침을 따르지 않을 경우 심각한 부상이나 사망에 이를 수 있습니다.

3. 설정 및 설치

3.1 풀기 및 검사

Carefully remove all components from the packaging. Inspect for any shipping damage. If damage is found, contact your supplier immediately.

3.2 사이트 선택

Choose a level, solid surface for the filter, preferably in a well-drained area. Ensure adequate clearance around the filter for future maintenance and servicing. The filter should be installed as close to the pool as possible to minimize friction loss from plumbing.

3.3 조립

  1. Position the filter tank base on the selected site.
  2. Carefully place the filter manifold and cartridges inside the lower tank half. Ensure they are seated correctly.
  3. Place the upper tank half onto the lower tank half, aligning the two halves.
  4. Secure the tank halves using the posi-ring closure. Ensure the ring is properly seated and tightened according to the manufacturer's specifications to prevent leaks and ensure safe operation.
  5. Connect the plumbing from the pool pump to the filter inlet and the return line to the filter outlet. Use appropriate sealants and fittings to ensure watertight connections.
  6. Install the pressure gauge into the designated port on the filter tank.
PLM200 Filter Assembly Diagram

그림 3.1: Illustration of the PLM200 filter assembly. This image represents the filter with its two-piece tank housing and the posi-ring closure, demonstrating how the components fit together during installation.

4. 사용 설명서

4.1 초기 시동

  1. Ensure all plumbing connections are secure and the filter drain plug is closed.
  2. Open the air relief valve on top of the filter tank.
  3. Start the pool pump. Allow the filter tank to fill with water, and air to escape through the air relief valve.
  4. 공기 배출 밸브에서 물이 꾸준히 흘러나오면 밸브를 닫으십시오.
  5. Note the initial pressure gauge reading. This is your clean filter operating pressure.

4.2 정상 작동

The PLM200 filter is designed for continuous filtration. Monitor the pressure gauge regularly. As dirt accumulates in the filter cartridges, the pressure will rise. When the pressure gauge reads 8-10 PSI above the clean filter operating pressure, it is time to clean the filter cartridges.

The filter's design, with complete media coverage and shallow pleats, optimizes dirt holding capabilities, leading to longer filter cycles and reduced cleaning frequency.

5. 유지관리

5.1 Cleaning the Filter Cartridges

WARNING: Always turn off the pump and relieve all pressure from the filter before opening the tank.

  1. 수영장 펌프를 끄고 전원을 차단하세요.
  2. Open the air relief valve to release any remaining pressure.
  3. Open the filter drain plug to drain the water from the tank.
  4. Remove the posi-ring closure and carefully lift the upper tank half.
  5. Remove the filter cartridges from the tank.
  6. Hose down the cartridges thoroughly with a garden hose to remove debris. For stubborn dirt or oils, use a specialized filter cleaning solution as directed by the cleaner manufacturer.
  7. Inspect cartridges for damage (tears, cracks). Replace damaged cartridges.
  8. 깨끗한 카트리지를 다시 설치하고 제대로 장착되었는지 확인하십시오.
  9. Reassemble the filter tank, securing the posi-ring closure.
  10. 필터를 다시 시작하려면 "초기 시작" 절차(섹션 4.1)를 따르십시오.
Cleaning PLM200 Filter Cartridges

그림 5.1: Representation of cleaning a filter cartridge. This image illustrates the process of hosing down a filter cartridge to remove accumulated debris, a key step in maintaining the PLM200 filter's efficiency.

5.2 방한처리

In areas subject to freezing temperatures, the filter must be drained and winterized to prevent damage. Consult your local pool professional for specific winterization procedures for your region.

6. 문제 해결

문제가능한 원인해결책
낮은 유량 / 높은 압력Clogged filter cartridgesClean filter cartridges (refer to Section 5.1)
낮은 유량 / 높은 압력시스템 내의 공기공기 배출 밸브를 사용하여 시스템에서 공기를 빼내십시오. 흡입 라인에 누출이 있는지 확인하십시오.
물탱크에서 물이 새고 있습니다Improperly seated posi-ring closure or O-ringTurn off pump, relieve pressure. Re-seat posi-ring and inspect O-ring for damage. Lubricate O-ring if dry.
물탱크에서 물이 새고 있습니다Cracked tank or fittingsInspect tank and fittings for cracks. Replace damaged components.
Filter Not Clearing WaterDamaged or worn filter cartridgesInspect and replace filter cartridges if damaged.
Filter Not Clearing Water부적절한 물 화학 성분수영장 물의 화학적 성분을 검사하고 균형을 맞춰주세요.

7. 사양

8. 보증 정보

Pentair warrants its products against defects in material and workmanship. The specific warranty period and terms may vary by product and region. Please refer to the official Pentair warranty statement included with your product packaging or visit the official Pentair web자세한 보증 정보는 사이트를 참조하십시오.

보증 청구를 위해 구매 증빙 자료를 보관하십시오.

9. 고객 지원

For technical assistance, replacement parts, or further information regarding your Pentair Sta-Rite PLM200 filter, please contact Pentair Customer Service.