1. 제품 오버view
The ENGINEER ST-21 is a high-quality replacement soldering iron tip specifically designed for use with the ENGINEER SK-40 series soldering irons. This tip features a precise 2.5x2mm diameter, making it suitable for detailed soldering applications. It is constructed from pure copper with plating for optimal heat transfer and durability.
Figure 1: The ENGINEER ST-21 Soldering Iron Tip. This image shows the metallic tip, which is a replacement part for compatible soldering irons.
Figure 2: Dimensional drawing of the ST-21 tip. This diagram illustrates the precise measurements of the tip, including its 2.5mm diameter and overall length, crucial for compatibility and application.
그림 3: example of a soldering iron, similar to the SK-40 series, with a tip in use on a circuit board. This image demonstrates the typical application of such a soldering tip in electronic work.
2. 설정 및 설치
The ST-21 soldering iron tip is designed for easy installation and replacement on compatible ENGINEER SK-40 series soldering irons. Ensure the soldering iron is unplugged and completely cool before attempting to change the tip.
2.1 Attaching the Tip
- 안전을 확보하세요: Disconnect the soldering iron from the power source and allow it to cool down completely. Handling a hot iron or tip can cause severe burns.
- 이전 팁 제거(해당되는 경우): If replacing an existing tip, carefully unscrew or pull off the old tip from the heating element/barrel of the soldering iron. Use heat-resistant gloves if the iron is still warm.
- 새로운 팁 삽입: Gently slide the ST-21 tip onto the heating element/barrel of your SK-40 series soldering iron. Ensure it is seated firmly and correctly.
- 팁을 확보하세요: If your soldering iron model requires it, tighten any retaining screws or collars to secure the tip in place. Do not overtighten.
- 초기 주석 도금: After installation and once the iron reaches operating temperature, apply a small amount of solder to the tip. This "tins" the tip, protecting it from oxidation and ensuring efficient heat transfer for future soldering tasks.
2.2 호환성
This tip is specifically compatible with ENGINEER SK-40 series soldering irons. Using it with incompatible models may result in poor performance, damage to the iron, or safety hazards. Always verify your soldering iron model before installing a new tip.
3. 사용 설명서
The ST-21 tip functions as the heat transfer point for your soldering iron. Proper operation of the soldering iron itself is crucial for effective and safe soldering. Refer to the instruction manual provided with your ENGINEER SK-40 series soldering iron for detailed operating procedures.
3.1 일반적인 사용 팁
- 예열: Allow the soldering iron to reach its full operating temperature before attempting to solder.
- 주석 도금: Regularly tin the tip with a small amount of solder to prevent oxidation and ensure good heat transfer. This should be done before and after each soldering session, and periodically during use.
- 청소: 광고 사용amp sponge or brass wool cleaner to wipe the tip clean of excess solder and flux residue frequently during use.
- 연락하다: Apply the tip to both the component lead and the PCB pad simultaneously to heat them evenly before applying solder.
- 납땜 적용: Apply solder to the heated joint, not directly to the soldering iron tip. The heat from the tip should melt the solder, allowing it to flow smoothly.
4. 유지관리
Proper maintenance of your ST-21 soldering tip will extend its lifespan and ensure consistent performance.
4.1 Cleaning the Tip
- Damp 스펀지: Use a dedicated soldering sponge, slightly dampened with water, to wipe the tip clean. Ensure the sponge is not soaking wet, as excessive water can cause thermal shock and damage the tip.
- Brass Wool Cleaner: A brass wool tip cleaner is an effective alternative for removing stubborn solder and oxidation without significantly lowering the tip's temperature.
- Tip Rejuvenator: For heavily oxidized tips that no longer accept solder, a tip rejuvenator compound can be used. Follow the product instructions carefully.
4.2 보관
When not in use, ensure the tip is clean and lightly tinned before storing the soldering iron. This protects the tip from oxidation during storage.
4.3 검사
Periodically inspect the tip for signs of wear, pitting, or excessive oxidation that cannot be cleaned. A severely worn tip will not transfer heat efficiently and should be replaced.
5. 문제 해결
If you encounter issues with your ST-21 soldering tip, consider the following common problems and solutions:
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| Tip does not heat up or heats slowly. | Poor contact with heating element, faulty heating element, or incorrect tip installation. | Ensure tip is fully seated. Check connection to soldering iron. If problem persists, the issue may be with the soldering iron itself, not the tip. |
| Solder does not flow well or beads up on the tip. | Oxidized tip, insufficient tinning, or incorrect temperature setting on the soldering iron. | Clean and re-tin the tip. If heavily oxidized, use a tip rejuvenator. Ensure the soldering iron is at the correct temperature for the solder being used. |
| Tip appears pitted or corroded. | Excessive heat, aggressive flux, or prolonged use without proper cleaning/tinning. | This indicates wear. The tip may need to be replaced. Ensure proper temperature settings and regular cleaning. |
6. 사양
| 특징 | 세부 사항 |
|---|---|
| 상표 | 엔지니어 |
| 제품 모델 번호 | ST-21 |
| 호환성 | ENGINEER SK-40 Series Soldering Irons |
| Tip Dimensions (approx.) | Diameter 2.5mm x 2mm (flat tip) |
| 재료 | Pure copper with plating |
| 제품 무게 | 12.1g |
| 패키지 크기 | 11.9 x 4.1 x 1cm |
| ASIN | B000TGFNP2 |
Note: The "Power Source: AC" specification found in some product listings refers to the compatible soldering iron, not the tip itself. The tip is a passive component.
7. 보증 및 지원
For specific warranty information regarding the ENGINEER ST-21 soldering iron tip, please refer to the documentation provided with your purchase or contact ENGINEER directly. As a consumable part, soldering tips typically have a limited warranty against manufacturing defects.
For further assistance or inquiries, you may visit the official ENGINEER brand store or contact their customer support.
공식 브랜드 스토어: ENGINEER Store on Amazon.co.jp
