1. 서론
The Kidde HD135F is a hardwired heat detector designed to provide early warning of dangerous temperature increases. This unit operates on your home's 120V AC power supply and includes a 9-Volt battery backup for continuous protection during power outages. Unlike smoke alarms, this heat detector responds to temperatures rising above 135° Fahrenheit (57.2° Celsius), making it suitable for areas where smoke or dust might cause false alarms in traditional smoke detectors, such as kitchens, garages, and attics. Integrating both heat and smoke detectors in your home can enhance overall fire safety.
2. 중요한 안전 정보
- 모든 지침 읽기: Before installation and operation, thoroughly read and understand this manual.
- 놓기: This heat alarm is recommended for areas where smoke alarms are not appropriate due to potential nuisance alarms, such as kitchens, garages, and attics.
- Interconnection Limits: When interconnecting with other Kidde devices, the system must not exceed the NFPA (National Fire Protection Association) limit of 18 initiating devices (smoke, heat, CO). Up to 6 strobe lights or relay modules can be interconnected in addition to the initiating devices.
- 작동 조건: Not recommended for use at temperatures below 32°F (0°C) or above 100°F (37.8°C), or in humidity higher than 95% relative humidity, as these conditions may reduce battery life or affect alarm performance.
- 연간 청소: Clean your alarm annually using compressed air or a vacuum cleaner around the perimeter of the alarm and the heat sensor guard. If cleaning does not restore the alarm to normal operation, it must be replaced.
- 페인트하지 마세요: Never paint the alarm. Paint can interfere with the sensor's ability to detect heat.
3. 패키지 내용
패키지에는 다음 항목이 포함되어 있어야 합니다.
- One Kidde HD135F Hardwired Heat Detector
- One 9-Volt Alkaline Battery (pre-installed or included separately)
- 장착 브래킷
- Quick-Connect Power Harness
- 사용 설명서
4. 특징
- Heat Sensing Technology: Detects temperatures rising above 135°F (57.2°C).
- 가청 경보: Sounds an 85-decibel alarm upon detection of elevated temperatures.
- 이중 전원: Operates on 120V AC hardwired power with a 9-Volt alkaline battery backup.
- Quick-Connect Power Harness: Facilitates fast and easy installation.
- LED 표시등:
- 녹색 LED : Constantly 'on' when AC power is present.
- 적색 LED : Flashes every 30-40 seconds during normal operation. Flashes rapidly when the unit is alarming due to high temperature.
- 배터리 부족 표시기: Alerts the user with a one-side chirp in the event of a low or missing battery.
- 테스트/무음 버튼: Allows for easy testing of the unit's electronic circuitry, horn, and battery function, and can temporarily silence nuisance alarms.
- Interconnection Capability: Can be interconnected with up to 24 compatible Kidde devices (up to 18 initiating devices like smoke, heat, or CO alarms, plus up to 6 strobe lights or relay modules).
- UL 인증: 안전 기준을 충족합니다.
5. 설치
Proper installation is crucial for the effective operation of your heat detector. Follow these steps carefully:
5.1 위치 선택
Install the heat detector on a ceiling or wall. For optimal performance, consider areas prone to rapid temperature increases but where smoke alarms might be prone to false alarms. Ideal locations include:
- 차고: Where vehicle exhaust or dust might trigger smoke alarms.
- 다락방: Where extreme temperatures can occur.
- 주방: To detect cooking fires without nuisance alarms from cooking fumes.
Avoid installing in areas with high humidity (e.g., bathrooms with showers) or extreme temperatures, as these can affect performance and battery life.
5.2 브래킷 장착
- 배전반을 준비하세요: Ensure power to the circuit is turned off at the main fuse or circuit breaker panel before beginning installation.
- 장착 브래킷 부착: Secure the mounting bracket to the electrical box on the ceiling or wall. Use the provided screws or appropriate hardware for your surface.
5.3 Wiring the Detector
- 전원 하네스 연결: Connect the quick-connect power harness to your home's 120V AC wiring. Typically, this involves connecting:
- Black wire to the hot (live) wire.
- White wire to the neutral wire.
- Red wire to the interconnect wire (if interconnecting multiple alarms).
- Attach Harness to Detector: Plug the quick-connect power harness into the receptacle on the back of the heat detector.
5.4 배터리 설치
- Insert 9V Battery: Open the battery compartment on the back of the detector. Insert the 9-Volt alkaline battery, ensuring correct polarity (+ to + and - to -). Close the compartment securely.
5.5 Attaching the Detector to the Bracket
- Twist On: 감지기를 장착 브래킷에 맞춰 정렬한 후 시계 방향으로 돌려 제자리에 단단히 고정될 때까지 돌립니다.
- 복원력 : Turn on the AC power at the main fuse or circuit breaker panel. The green LED on the detector should illuminate, indicating AC power is present.
6. 운영
6.1 정상 작동
During normal operation, with AC power connected, the green LED will be continuously lit. The red LED will flash approximately every 30-40 seconds to indicate that the unit is functioning correctly.
6.2 검출기 테스트
Test your heat detector weekly to ensure proper function:
- Press and hold the Test/Hush button located on the front of the detector.
- The alarm will sound a loud, pulsating tone, and the red LED will flash rapidly.
- Release the button. The alarm should stop, and the red LED should return to its normal flash pattern.
메모: The alarm is loud. Stand at arm's length from the unit when testing.
6.3 경보 조건
If the ambient temperature around the detector rises above 135°F (57.2°C), the unit will sound a loud, pulsating 85-decibel alarm. The red LED will flash rapidly during the alarm condition. If interconnected, all compatible alarms in the system will also sound.
6.4 소음 제거 기능
The Hush feature can temporarily silence the alarm for approximately 7-10 minutes. This is useful for nuisance alarms caused by temporary high heat sources (e.g., a very hot oven). To activate Hush:
- Press the Test/Hush button briefly during an alarm.
- The alarm will silence, and the red LED will flash every 1.5 seconds to indicate it is in Hush mode.
- After the Hush period, if the temperature is still above 135°F, the alarm will reactivate.
7. 유지관리
7.1 배터리 교체
The 9-Volt battery provides backup power during AC outages. Replace the battery immediately when the unit emits a one-side chirp approximately every 30-40 seconds, indicating a low or missing battery.
- 전원 끄기: Disconnect AC power to the detector at the circuit breaker.
- 감지기 제거: Twist the detector counter-clockwise from its mounting bracket.
- 개방형 배터리 칸: 배터리실 도어를 엽니다.
- 베터리 교체: Remove the old 9-Volt battery and insert a new one, observing polarity.
- 구획 닫기: 배터리 칸 문을 단단히 닫으세요.
- Reattach Detector: Twist the detector clockwise onto its mounting bracket until it locks.
- 전원 복구 및 테스트: Restore AC power and test the unit as described in Section 6.2.
7.2 감지기 청소
Clean your heat detector at least once a year to prevent dust and debris from affecting its performance.
- 전원 끄기: Disconnect AC power to the detector at the circuit breaker.
- 깨끗한 외관: Use a soft cloth to wipe the exterior of the detector.
- 센서 영역 청소: Use a vacuum cleaner with a soft brush attachment or compressed air to clean around the perimeter of the alarm and the heat sensor guard.
- 전원 복구 및 테스트: Restore AC power and test the unit as described in Section 6.2.
8. 문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| Alarm sounds intermittently or for no apparent reason. | Nuisance alarm due to temporary high heat (e.g., cooking). | Press the Hush button to temporarily silence the alarm. Ensure proper ventilation in the area. |
| Unit chirps once every 30-40 seconds. | Low or missing 9-Volt battery. | Replace the 9-Volt battery immediately (refer to Section 7.1). |
| 녹색 LED가 꺼져 있습니다. | AC 전원이 없습니다. | Check circuit breaker. Ensure power harness is securely connected. |
| Red LED is not flashing during normal operation. | Unit malfunction or dirty sensor. | Clean the detector (refer to Section 7.2). If the issue persists, the unit may need replacement. |
| Alarm does not sound when Test button is pressed. | Dead battery, no AC power, or unit malfunction. | Check AC power and replace battery. If still no alarm, replace the unit. |
9. 사양
- 모델: HD135F
- 전원: 120V AC, 60Hz, 80mA max; 9V Alkaline Battery Backup
- 알람 유형: Fixed Temperature Heat Alarm
- 활성화 온도: 화씨 135도(섭씨 57.2도)
- 가청 경보: 85피트에서 10dB
- 작동 습도: 5% - 95% Relative Humidity (non-condensing)
- 치수: Approximately 4"D x 4"W x 2"H (10.16 cm x 10.16 cm x 5.08 cm)
- 무게: 약 10.4온스(295그램)
- 상호 연결: Up to 24 Kidde devices (max 18 initiating devices)
- 인증: UL 인증
- 재료: 플라스틱
10. 보증 및 지원
10.1 제한 보증
The Kidde HD135F Heat Detector comes with a 5년 제한적 제조사 보증 from the date of purchase. This warranty covers defects in materials and workmanship under normal use and service. For specific warranty terms and conditions, please refer to the documentation included with your product or contact Kidde customer support.
10.2 고객 지원
For technical assistance, warranty claims, or service inquiries, please contact Kidde Safety:
- 핸드폰: 1-800-880-6788
- 주소: Kidde Safety, Mebane, NC 27302, USA
- Web대지: Kidde 공식 웹사이트를 방문하세요. web추가 리소스 및 FAQ 사이트.
11. 폐기
When the heat detector reaches the end of its service life or needs replacement, dispose of it in accordance with local regulations for electronic waste. The 9-Volt battery should be removed and recycled separately if possible, following local battery recycling guidelines.
