소개
This manual provides instructions for the installation, operation, and maintenance of the Linear Multi-Code Keypad Transmitter, model 420001. This wireless keypad is designed for use with Multi-Code Receivers to control access to garage doors or gates.
제품 끝view
The Linear Multi-Code Keypad Transmitter 420001 is a 12-button alphanumeric keypad. It operates on a 300 MHz frequency and features 10 dip switches for programming. Its weatherproof casing는 실외 사용에 필요한 내구성을 보장합니다.
이미지: 앞면 view of the Linear Multi-Code Keypad Transmitter 420001, showing the 12-button alphanumeric keypad and the "MULTI-CODE" branding at the top.
설정 및 설치
배터리 설치
The keypad requires one 9V alkaline battery (not included). To install:
- Open the keypad casing.
- Connect the 9V battery to the battery clip.
- Place the battery securely within the compartment.
- Close the keypad casing, ensuring it is sealed properly for weather resistance.
설치
The keypad is designed for screw-in installation and mounts with two screws.
- Choose a suitable location for mounting, ensuring it is within range of your Multi-Code Receiver.
- Mark the positions for the two mounting screws.
- 필요한 경우 시험용 구멍을 뚫습니다.
- Secure the keypad to the surface using appropriate screws.
키패드 프로그래밍
This keypad uses 10 dip switches for programming. The code is entered directly through the keypad, eliminating the need to manually adjust physical dip switches on the unit itself.
- Locate the dip switch settings on your Multi-Code Receiver or existing remote. This will be a sequence of 10 switches, each set to ON, OFF, or MIDDLE (if applicable).
- On the 420001 keypad, enter the 10-digit code corresponding to your receiver's dip switch settings. Refer to the keypad's internal instructions for specific key presses to represent ON, OFF, or MIDDLE positions.
- Press the "ACCESS" button to save the code.
- Test the keypad to ensure it operates your garage door or gate opener.
메모: Programming typically takes less than 2 minutes. Ensure the keypad is within operational range of the receiver during testing.
작동 지침
To operate your garage door or gate using the Linear Multi-Code Keypad Transmitter:
- Enter your programmed 10-digit access code using the alphanumeric buttons.
- Press the "ACCESS" button.
- The LED indicator will illuminate, and your Multi-Code Receiver should activate, opening or closing your garage door or gate.
If the door or gate does not respond, verify your code and ensure the keypad is within effective range of the receiver.
유지
- 배터리 교체: When the keypad's performance degrades or the LED indicator fails to light, replace the 9V battery. Follow the battery installation steps.
- 청소: Clean the keypad's exterior with a soft, damp 천으로 닦으세요. 연마성 세제나 용제는 사용하지 마세요.
- 내후성: The keypad features a weatherproof casing. Ensure the casing is properly closed and sealed after any internal access (e.g., battery replacement) to maintain its weather-resistant properties.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| Keypad does not respond or works intermittently. |
|
|
| LED 표시등이 켜지지 않습니다. | 배터리가 방전되었거나 제대로 설치되지 않았습니다. | Check battery connection or replace the 9V battery. |
| Keypad does not program correctly. | Incorrect dip switch settings entered. | Double-check the 10 dip switch settings from your receiver and re-enter the code carefully. |
명세서
| 모델 번호 | 420001 |
| 상표 | 선의 |
| 빈도 | 300MHz |
| Number of Dip Switches | 10 |
| 전원 | 9V 알칼리 배터리 1개 (별도 구매) |
| 설치 유형 | 나사로 고정 |
| 제품 치수 | 6.75 x 1.5 x 3 인치 |
| 품목 무게 | 4 온스 |
| 재료 | 플라스틱 |
| 색상 | 베이지색 |
| 규정 준수 | 연방통신위원회(FCC) |
보증 및 지원
보증 정보나 기술 지원에 대해서는 제조업체의 공식 웹사이트를 참조하십시오. web해당 사이트를 방문하거나 고객 서비스 부서에 문의하세요. 보증 청구를 위해 구매 영수증을 보관하세요.
제조업체: 선의
