제품 끝view
The Rubbermaid Direct Wall Shelf, 3 Ft. Wide, is a versatile wire shelving system designed to enhance storage in various areas of your home. Its ventilated design promotes air circulation, helping to keep stored items fresh. This kit provides a simple and effective solution for adding storage where it's needed most, such as laundry rooms, linen closets, bathrooms, mudrooms, pantries, or general storage areas.
주요 특징
- 공간 최적화: Fits any closet or wall with 3 ft. of horizontal space, offering 3 cubic feet of shelf space and 3 feet of hanging space.
- 대용량: Supports up to 135 lbs of overall weight.
- 간편한 설치: Includes all necessary support braces and installation hardware for a complete setup.
- 내구성 있는 구조: Made from epoxy-coated steel for strength and durability, designed not to stain or snag clothing.
- 통풍 설계: Promotes air circulation to keep items fresh.
- Integrated Hanging Rod: Features an integrated rod for hanging clothes.
- 미적 : Contemporary white finish for a sleek and clean appearance.
중요한 안전 정보
- 중량 용량: DO NOT EXCEED 135 lbs WEIGHT CAPACITY. Overloading can lead to structural failure and injury.
- 환경: KEEP AWAY FROM WET ENVIRONMENTS UNLESS PROPERLY SEALED. Moisture can compromise the integrity of the installation and product.
- 설치: Ensure all mounting hardware is securely fastened into wall studs or appropriate anchors for maximum stability.
패키지 내용
Your Rubbermaid Direct Wall Shelf kit includes the following components:
- 1 x 3 Ft. Wire Shelf
- 2 x Support Brackets
- 설치 하드웨어(나사, 벽 앵커)
설치 가이드
필요한 도구
- 연필
- 줄자
- 수준
- 스터드 찾기
- Drill with appropriate bits (1/8 inch for pilot holes, 3/8 inch for wall anchors if no stud)
- 해머(벽 앵커용)
단계별 설치
- 측정 및 표시: Determine the desired height for your shelf. Use a tape measure and pencil to draw a level line on the wall where the top of the shelf will be.
- 스터드 찾기: Use a stud finder to locate wall studs along your level line. Mark the center of each stud. Attaching the shelf directly to studs is recommended for maximum weight capacity.
- Install Wall Clips: Position the wall clips along the marked line, ensuring they align with studs where possible. If a stud is not available within 4 inches of the shelf ends, use the provided wall anchors. Drill 1/8-inch pilot holes into studs. For non-stud locations, drill a 3/8-inch hole and insert a wall anchor, tapping it flush with a hammer. Secure the wall clips with screws.
- Attach Shelf to Wall Clips: Carefully place the wire shelf onto the installed wall clips. Ensure the shelf is level and fully seated in the clips.
- 지지 브래킷 설치: Position the support brackets underneath the shelf, aligning them with the bottom of the shelf and the wall. Mark the drill points for the bottom of the brackets. Drill pilot holes and secure the brackets to the wall using screws, preferably into studs or with appropriate wall anchors.
- Secure Shelf to Brackets: The shelf should rest securely on the support brackets. Some brackets may have locking mechanisms to further secure the shelf.
설치 영상 참조
사용 지침
The Rubbermaid Direct Wall Shelf is designed for efficient and organized storage. To ensure optimal performance and longevity, please adhere to the following guidelines:
- 무게 분포 : Distribute items evenly across the shelf surface. Avoid concentrating heavy items in one spot.
- 최대 하중: 최대 중량 한도인 135파운드를 초과하지 마십시오.
- 통풍: The ventilated design is ideal for items requiring air circulation, such as linens, towels, or laundry.
- 걸어두는 물건: Utilize the integrated hanging rod for clothes or other items that benefit from hanging storage.
관리 및 유지 보수
To keep your Rubbermaid Direct Wall Shelf in excellent condition, follow these simple care instructions:
- 청소: Hand wash only. Use a soft cloth with mild soap and water to clean the epoxy-coated steel. Avoid abrasive cleaners or scouring pads that could damage the finish.
- 건조: Ensure the shelf is thoroughly dried after cleaning to prevent water spots or potential rust, especially if used in humid environments.
- 점검: Periodically check all mounting hardware and support brackets to ensure they remain tight and secure. Tighten any loose screws as needed.
문제 해결
If you encounter any issues with your Rubbermaid Direct Wall Shelf, consider the following common solutions:
- 선반이 수평이 아닙니다. Recheck your initial measurements and the placement of wall clips and support brackets. Adjust as necessary to achieve a perfectly level surface.
- Shelf feels unstable: Ensure all screws are tightened securely into wall studs. If wall anchors were used, verify they are properly installed and holding firmly. Avoid exceeding the 135 lbs weight limit.
- Items snagging on shelf: The epoxy-coated steel is designed to prevent snagging. If this occurs, inspect the shelf for any damage or rough spots that may have developed.
제품 사양
| 특징 | 사양 |
|---|---|
| 모델명 | Direct Wall Mount Closet Shelf, 3 Ft. Wide, Mounting Hardware Kit Included |
| 모델 번호 | 3E0000WHT |
| 치수(D x W x H) | 1.91인치 깊이 x 36인치 너비 x 11.96인치 높이 |
| 크기 | 3' Length |
| 중량 제한 | 135 파운드 |
| 재료 | Stainless Steel (Epoxy-coated) |
| 색상 | 하얀색 |
| 선반 수 | 1 |
| 조립이 필요합니다 | 설치 필요 없음 |
| 설치 유형 | 벽걸이형 |
| 추천 용도 | Bathroom, Closet, Laundry Room, Garage |
보증 및 지원
보증: This product comes with a manufacturer's warranty. Please refer to the specific warranty documentation included with your purchase or visit the official Rubbermaid web자세한 이용 약관은 사이트를 참조하세요.
고객 지원: For any questions, missing parts, or assistance with installation, please contact Rubbermaid customer support. You can typically find contact information on the product packaging or on the official Rubbermaid web대지.