소개
The Linear ACT-31B 1-Channel Keychain Transmitter is designed for use with Linear Access MegaCode receivers and controllers. This compact device provides convenient remote access, operating on a frequency of 318 MHz. It is equipped with a single channel for activation and includes two 2016-type Lithium batteries for immediate use. Its design focuses on portability and ease of integration with compatible Linear systems.
제품 끝view
Figure 1: Linear Act-31B 1-Channel Keychain Transmitter. This image displays the black, oval-shaped keychain transmitter with a single gray circular button on its face. It is attached to a metal split key ring via a black plastic quick-disconnect mechanism, highlighting its compact and portable design.
주요 특징:
- MegaCode Format: Factory-programmed to support over 1 million unique codes, ensuring high security.
- Single Channel Operation: Designed for straightforward control of one compatible Linear access device.
- 작동 주파수: Functions at 318 MHz for reliable signal transmission.
- 컴팩트한 디자인: Features a quick-disconnect key ring for easy attachment to keys or other items.
- 전원: Powered by two 2016-type Lithium batteries (included).
설정
To set up your Linear ACT-31B Keychain Transmitter with a compatible Linear Access MegaCode receiver or garage door opener, follow these steps:
- 학습 버튼을 찾으세요: On your Linear garage door opener unit (typically mounted on the ceiling), locate the 'LEARN' button. This button is usually small and may be red or another color, often accompanied by an LED indicator.
- 학습 모드 활성화: Press and release the 'LEARN' button on your garage door opener. The LED indicator light on the opener should illuminate or flash, indicating that the unit is now in learn mode and ready to accept a new remote code.
- Program the Transmitter: Within approximately 30 seconds of activating the learn mode on the opener, press the button on your ACT-31B Keychain Transmitter. Hold the button down for a few seconds. The LED light on the garage door opener should blink or turn off, confirming that the transmitter has been successfully programmed.
- 테스트 작업: Release the button on the transmitter. Wait a few seconds, then press the button again to test if the garage door responds. If the door opens or closes, the programming was successful.
If the transmitter does not work after following these steps, refer to the troubleshooting section or the full installation manual for your specific garage door opener model.
작동 지침
The Linear ACT-31B is a single-channel transmitter, meaning it controls one device. To operate your garage door or compatible Linear access device:
- 활성화: Simply press and release the single gray button on the face of the transmitter.
- 범위: The transmitter has a maximum operating range of approximately 10 meters (33 feet). Optimal performance is achieved within this range, though environmental factors can affect signal strength.
- 빈도: The device transmits on a 318 MHz frequency. Ensure your receiver is compatible with this frequency.
유지
배터리 교체:
The ACT-31B transmitter uses two 2016-type Lithium batteries. If the transmitter's range decreases significantly or it stops responding, the batteries may need replacement.
- C 열기asing: 송신기 c를 조심스럽게 여세요asing. This may involve gently prying it open along the seam with a small flat-head screwdriver or similar tool.
- 오래된 배터리 제거: Note the orientation of the existing batteries (+/-). Remove the old 2016-type Lithium batteries.
- 새 배터리 삽입: Insert two new 2016-type Lithium batteries, ensuring they are correctly oriented according to the polarity markings inside the casing.
- C 닫기asing: c를 찍으세요asing를 다시 단단히 결합하세요.
After replacing the batteries, it may be necessary to re-program the transmitter to your garage door opener if it does not respond immediately. Refer to the 'Setup' section for programming instructions.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 송신기가 작동하지 않습니다. | 배터리가 소모되었거나 부족합니다. | Replace the two 2016-type Lithium batteries. |
| Transmitter has reduced range. | Weak batteries or environmental interference. | Replace batteries. Ensure no large metal objects or strong radio signals are blocking the path. |
| Transmitter was working, now it isn't. | Loss of programming or incompatible receiver. | Re-program the transmitter following the 'Setup' instructions. Verify your garage door opener is a Linear Access MegaCode compatible model. |
| Must press button repeatedly for it to work. | Intermittent signal or weak connection. | Check battery strength. Ensure the transmitter is within optimal range. Re-program if necessary. |
명세서
- 모델 번호: ACT-31B
- 제품 크기: 0.48 x 1.25 x 2.25 인치
- 품목 무게: 0.48 온스
- 색상: 검은색
- 배터리: 2 Lithium Metal batteries (2016-type) required (included)
- 연결 기술 : 고주파
- 작동 주파수: 318MHz
- 최대 범위: 10미터 (약 33피트)
- 특별 기능: 인체공학적 디자인, 경량
- 호환 장치: Linear Access MegaCode receivers and controllers
- 제조업체: Linear / Nortek
- 상자 안에 무엇이 들어있나요? Key Chain Transmitter (1 Channel)
보증 및 지원
For specific warranty information regarding your Linear ACT-31B 1-Channel Keychain Transmitter, please refer to the documentation included with your purchase or contact Linear customer support directly. Warranty terms may vary.
Additional support resources, including detailed installation and user manuals, are available:
- 설치 설명서(PDF): View 설치 설명서
- 사용자 매뉴얼(PDF): View 사용자 설명서
For technical assistance or further inquiries, please contact Linear customer service.
