1. 제품 오버view
The BELL HUBBELL WIRING 752 Square Flat Blank Angle Mounting Cover is designed to securely close an outlet box or provide a mounting surface for a device. Constructed from durable steel and finished in gray, this cover features angled mounting slots to facilitate precise alignment and compensate for minor box misalignments during installation.
주요 특징:
- 목적: Used to close an outlet box or mount a device.
- Angled Mounting Slots: Allows for correction of box misalignment, ensuring a flush and secure fit.
- 재료: Durable steel construction for longevity.
- 구성: Square design.
이미지 1.1: 앞쪽 view of the BELL HUBBELL WIRING 752 Square Flat Blank Angle Mounting Cover. This image displays the gray steel cover with its distinctive angled mounting slots at each corner, designed for secure and adjustable installation.
2. 설정 및 설치
This section provides instructions for the proper installation of your BELL HUBBELL WIRING 752 cover. Ensure all power is disconnected before beginning any electrical work.
- 안전이 최우선입니다. Before starting installation, ensure the power supply to the electrical box is turned off at the circuit breaker. Verify with a voltag전자 테스터.
- 상자 준비: Ensure the electrical box is clean and free of debris.
- 덮개 위치: Place the BELL 752 cover over the electrical box, aligning the mounting slots with the screw holes on the box.
- Utilize Angled Slots: The angled mounting slots are designed to help correct minor misalignments of the electrical box. Adjust the cover slightly as needed to achieve a flush and level fit against the wall or surface.
- 덮개를 고정하십시오: Insert appropriate mounting screws (not included) through the angled slots and into the electrical box. Tighten the screws firmly but do not overtighten, which could warp the cover or damage the box.
- 최종 확인: Once secured, ensure the cover is flush and stable. Restore power to the circuit.
3. 사용 설명서
The BELL HUBBELL WIRING 752 cover functions as a protective closure for an electrical box or a stable base for mounting other electrical devices. Once installed, its operation is passive.
- 보호: The cover provides a physical barrier, protecting the internal wiring and components of the electrical box from dust, debris, and accidental contact.
- 장치 장착: If used for mounting a device, ensure the device is securely attached to the cover using appropriate fasteners.
4. 유지관리
The BELL HUBBELL WIRING 752 cover requires minimal maintenance to ensure its longevity and appearance.
- 청소: Periodically wipe the cover with a soft, damp cloth to remove dust and dirt. Avoid abrasive cleaners or solvents, which may damage the finish.
- 점검: Annually inspect the cover for any signs of damage, corrosion, or loose mounting screws. Tighten screws if necessary, ensuring not to overtighten.
- 부식: As the cover is made of steel, ensure it is not exposed to excessive moisture or corrosive environments unless specifically rated for such conditions.
5. 문제 해결
This section addresses common issues you might encounter with the BELL HUBBELL WIRING 752 cover.
- Issue: Cover does not sit flush.
해결책: Loosen the mounting screws slightly. Utilize the angled mounting slots to adjust the cover's position until it sits flush. Retighten the screws. If the box itself is severely misaligned, professional electrical assistance may be required to adjust the box.
- Issue: Cover feels loose after installation.
해결책: Ensure the mounting screws are adequately tightened. Do not overtighten, as this can strip the screw threads in the electrical box. If the screw holes in the box are stripped, consider using larger screws or a repair kit for the electrical box.
- Issue: Visible corrosion or damage.
해결책: If the cover shows significant corrosion or damage, it should be replaced to maintain safety and aesthetic integrity. Ensure the environment is suitable for a steel cover.
6. 사양
| 기인하다 | 세부 사항 |
|---|---|
| 모델 번호 | 752 |
| 상표 | BELL (HUBBELL WIRING) |
| 재료 | 강철 |
| 색상 | 회색 |
| 구성 | 정사각형 |
| 설치 유형 | 나사로 고정 |
| 품목 치수(L x W x H) | 4 x 4 x 0.5 인치 |
| 품목 무게 | 1.3파운드 |
| 제조업체 부품 번호 | 752 |
| 한국어: | 050169907528 |
7. 보증 정보
The BELL HUBBELL WIRING 752 Square Flat Blank Angle Mounting Cover comes with a manufacturer's warranty.
- 보증 기간: 1년
- 적용 범위: This warranty covers defects in materials and workmanship under normal use. It does not cover damage resulting from improper installation, misuse, abuse, or unauthorized modifications.
- 청구 프로세스: For warranty claims, please retain your proof of purchase and contact BELL customer support.
8. 지원 및 연락처
For further assistance, technical support, or inquiries regarding your BELL HUBBELL WIRING 752 cover, please contact the manufacturer.
- 제조업체: HUBBELL WIRING
- 상표: 벨
- 온라인 리소스: BELL 공식 웹사이트를 방문하세요. web제품 정보 및 지원을 제공하는 사이트입니다.
- 고객 서비스: Refer to the packaging or the manufacturer's web최신 연락처 정보(전화번호, 이메일)를 확인하려면 이 사이트를 방문하세요.
