PJRIW0TT3K 온도 컨트롤러 사용 설명서

소개

This manual provides essential information for the safe and efficient operation of your PJRIW0TT3K Temperature Controller. Please read this manual thoroughly before installation and use, and keep it for future reference.

Figure 1: PJRIW0TT3K Temperature Controller Front View

The PJRIW0TT3K is a universal wire-controlled temperature controller designed for various applications. It features a digital display and intuitive button controls for setting and monitoring temperature.

명세서

설정 및 설치

The PJRIW0TT3K Temperature Controller is designed for wire control. Proper installation is crucial for safe and accurate operation. Due to the nature of industrial control devices, it is highly recommended that installation and wiring be performed by a qualified professional.

일반 설치 지침:

• 전원 차단: Always ensure that power to the system is completely disconnected before attempting any installation or wiring.
• 설치: Mount the controller in a location free from excessive vibration, moisture, and extreme temperatures. Ensure adequate ventilation.
• 배선: Connect the controller according to the specific wiring diagram provided with your system or application. Pay close attention to power input, sensor input, and output connections. Incorrect wiring can damage the device or connected equipment.
• 센서 연결: Connect the temperature sensor to the designated input terminals. Ensure the sensor type is compatible with the controller.
• 출력 연결: Connect the control output (e.g., to a heater, cooler, or relay) to the appropriate output terminals. Verify load compatibility.
• 전원 연결: Connect the power supply to the controller's power input terminals. Double-check voltag전자와 극성.

Warning: Incorrect wiring can lead to electric shock, fire, or damage to the equipment. If you are unsure about any part of the installation process, consult a qualified electrician or technician.

작동 지침

The PJRIW0TT3K Temperature Controller features a digital display and several control buttons for operation. While specific functions may vary slightly based on the application, the general operation involves setting the desired temperature and monitoring the current temperature.

Control Buttons (Refer to Figure 1):

• 디스플레이 화면: Shows the current temperature, set temperature, and various operational parameters.
• 설정 버튼: Typically used to enter the setting mode to adjust parameters like target temperature, hysteresis, and calibration. Pressing it usually allows you to cycle through different settings.
• K1 / K2 Buttons: These are likely used for increasing (K1) or decreasing (K2) values when in setting mode, or for navigating through menu options. They might also serve as quick access buttons for specific functions.
• °F Button: This button is likely used to switch the temperature display unit between Celsius (°C) and Fahrenheit (°F).

기본 작업:

1. 전원 켜기: After proper installation and wiring, apply power to the controller. The display should illuminate and show the current temperature.
2. 목표 온도 설정:
   • 를 누르세요 세트 button. The display may flash or show the current setpoint.
   • 사용하세요 K1 (위) 그리고 K2 (Down) buttons to adjust the target temperature to your desired value.
   • 누르다 세트 again (or wait for a timeout) to confirm and save the new setpoint.
3. 온도 단위 변경: 를 누르세요 ° 화씨 button to toggle between Celsius and Fahrenheit display modes.
4. 모니터링: The controller will continuously monitor the temperature and activate/deactivate the output based on the set temperature and control logic (e.g., heating or cooling mode).

For advanced settings and specific control modes, refer to the detailed programming guide that may accompany your specific application or system integration.

유지

The PJRIW0TT3K Temperature Controller is designed for reliable operation with minimal maintenance. However, regular checks and proper care can extend its lifespan and ensure continued accuracy.

• 청소: Periodically clean the exterior of the controller with a soft, dry cloth. Do not use abrasive cleaners, solvents, or excessive moisture, as these can damage the display or internal components.
• 환경 조건: Ensure the controller operates within its specified environmental limits (temperature, humidity). Avoid exposing it to direct sunlight, extreme heat, cold, or corrosive environments.
• 사이: Periodically inspect all wiring connections for tightness and signs of corrosion or damage. Loose connections can lead to intermittent operation or system failure.
• 센서 점검: Verify that the temperature sensor is clean and properly positioned. Dust or debris on the sensor can affect readings.
• 전원 재부팅(필요한 경우): If the device exhibits unusual behavior, a brief power cycle (turning off and then on again) may resolve minor issues.

Caution: Do not attempt to open the controller casing. There are no user-serviceable parts inside, and doing so will void any potential warranty and may expose you to electrical hazards.

문제 해결

If you encounter issues with your PJRIW0TT3K Temperature Controller, refer to the following common troubleshooting steps:

위의 단계를 시도한 후에도 문제가 지속되면 고객 지원팀에 문의하여 추가 지원을 받으십시오.

사용자 팁

• 안정적인 전원 공급 장치: Ensure the controller is connected to a stable power supply to prevent erratic behavior or damage from voltag전자 변동.
• 환경 제어: For optimal performance and longevity, operate the controller within a clean, dry environment and avoid extreme temperatures.
• 정기 모니터링: Periodically check the display to ensure the temperature readings are consistent with expectations and the system is operating as intended.

보증 및 지원

This product is supplied by SJSK PLC Module Store, a company with 5 years of experience in the PLC module industry.

고객 지원:

For technical assistance, troubleshooting, or any inquiries regarding your PJRIW0TT3K Temperature Controller, please contact the seller's customer service. They are available online from 11:00 to 24:00 (local time, likely China Standard Time).

Please have your product model number (PJRIW0TT3K) ready when contacting support to facilitate a quicker resolution.

보증 정보:

Specific warranty terms and conditions are typically provided at the point of purchase or by the seller. Please refer to your purchase documentation or contact SJSK PLC Module Store directly for detailed warranty information.