SINOTIMER TM630A 12V DC Programmable Digital Timer Switch

소개

The SINOTIMER TM630A is a compact, programmable digital timer switch designed to automatically control various electrical equipment by switching them on and off at preset times. This device is suitable for a wide range of applications, including controlling streetlights, neon signs, lamps, water heaters, air conditioners, billboards, electric cookers, boosters, sprayers, bottlers, preheaters, agriculture facilities, and broadcasting equipment. It features a built-in battery to retain programmed settings during power failures, ensuring reliable operation. The TM630A is built with a high-accuracy CMOS chip, offers strong anti-jamming capabilities, and is simple to set up and operate. It conforms to IEC 60367 standards and is CE certified.

명세서

설정

1. 설치

The TM630A timer switch can be installed either on a DIN rail or screw-mounted. Ensure the installation location is dry, well-ventilated, and within the specified temperature range (-20°C to +50°C).

2. 배선도

Refer to the following wiring diagram for proper connection. Ensure all connections are secure and comply with local electrical codes. This diagram shows the connections for the 12V DC/AC input and the load output.

The timer has two input terminals for power (typically marked L and N for AC, or + and - for DC) and two output terminals for the load.

3. 초기 전원 켜기

Upon initial power-up or after extended storage, the internal 1.2V rechargeable battery may be low. Connect the timer to its power supply (12V DC/AC) for a few hours to allow the internal battery to charge. This battery maintains the programmed settings during power outag에스.

작동 지침

1. 버튼 기능

Familiarize yourself with the buttons on the front panel:

• C/R (취소/회수): 현재 설정을 초기화하거나 저장된 프로그램을 불러옵니다.
• D+ (낮): 요일을 조정합니다.
• H+ (시간): 시간을 조정합니다.
• M+ (분): 분을 조정합니다.
• P (Program/Timer): 프로그래밍 모드로 들어갑니다.
• 시계: Used in combination with D+, H+, M+ to set the current time and day.
• 수동: Manually switches the output ON/OFF or sets to AUTO mode.

2. Setting the Present Time and Day

To set the current time and day of the week:

1. 를 누르고 계세요 시계 단추.
2. 잡고 있는 동안 시계, 누르다 시간 현재 시간을 설정합니다.
3. 잡고 있는 동안 시계, 누르다 분 현재 분을 설정합니다.
4. 잡고 있는 동안 시계, 누르다 낮 현재 요일을 설정합니다.

3. ON/OFF 시간 프로그래밍

The timer supports up to 16 ON/OFF programs per day or week. Follow these steps to set your desired schedules:

1. 를 누르세요 시간제 노동자 (P) button once to enter the 1st ON time setting. The display will show "1 ON".
2. 누르다 시간, 분, 그리고 낮 buttons to set the desired time and day(s) for the 1st ON event.
   • 낮 button allows selecting various combinations of days (e.g., MO, TU, WE, TH, FR, SA, SU; MO, TU, WE, TH, FR; SA, SU; MO, WE, FR; TU, TH, SA; MO, TU, WE; TH, FR, SA; MO, WE, FR, SA; MO, TU, WE, TH, FR, SA, SU).
3. 를 누르세요 시간제 노동자 (P) button again. The display will show "1 OFF".
4. 누르다 시간, 분, 그리고 낮 buttons to set the desired time and day(s) for the 1st OFF event.
5. Repeat steps 1-4 for additional ON/OFF programs (up to 16 pairs).
6. 프로그래밍 모드를 종료하려면 시계 단추.

4. 수동 조작

그만큼 수동 button allows you to override the programmed settings temporarily or permanently:

• 누르다 수동 repeatedly to cycle through modes: ON (always on), OFF (always off), and AUTO (follows programmed schedule).
• In AUTO mode, the timer will execute the programmed ON/OFF events.

유지

1. 내부 배터리

The TM630A includes a 1.2V rechargeable internal battery. This battery automatically recharges when the timer is connected to its power supply. It is designed to retain your programmed settings for up to 60 days during power outages. If the timer has been stored for a long period without power, allow it to charge for several hours before programming to ensure full memory retention.

2. 청소

To clean the timer, gently wipe the exterior with a soft, dry cloth. Do not use abrasive cleaners, solvents, or immerse the device in water.

문제 해결

• 디스플레이가 비어 있습니다: Check if the timer is receiving power (12V DC/AC). If it has been without power for an extended period, the internal battery may be fully discharged. Connect to power and allow it to charge.
• 프로그램이 실행되지 않습니다:
  • 타이머가 켜져 있는지 확인하세요 자동차 mode (check the display for "AUTO"). Press the 수동 button to cycle to AUTO mode if necessary.
  • 현재 시간과 날짜가 올바르게 설정되어 있는지 확인하십시오.
  • Check that the ON/OFF programs are correctly entered and enabled.
• 시간 편차: The timer has an auto time error correction of +/- 30 seconds weekly. Significant deviations may indicate an issue with the power supply or internal components.
• Loss of programs after power outage: While the internal battery provides memory retention for up to 60 days, prolonged power outages or a depleted internal battery can lead to program loss. Ensure the internal battery is adequately charged.

사용자 팁

• For critical applications, consider testing your programmed schedules after initial setup to ensure they function as expected.
• 이점을 활용하세요tage of the 15 programming group combinations to create complex weekly schedules for different days or sets of days.
• The manual override function is useful for temporary changes without altering your saved programs.
• Given its wide application range, this timer is highly versatile. Consider using it for automating garden irrigation, aquarium lighting, or even charging cycles for low-voltag전자 장치.

보증 및 지원

The SINOTIMER TM630A timer switch is certified with CE, RoHS, EMC, and LVD standards, indicating compliance with relevant health, safety, and environmental protection directives.

For warranty information, technical support, or service inquiries, please contact your original point of purchase or the manufacturer directly. The product package includes a manual in Russian, Portuguese, and English languages for detailed guidance.