HGLRC 5-12V BEC Step-down Module User Manual

1. 서론

The HGLRC 5-12V BEC Step-down Module is a versatile power management component designed for RC FPV drones and similar applications. It efficiently converts a wide input voltage range (8.4V-28V) into stable 5V or 12V outputs, supporting a working current of up to 2A. This module offers flexible connection options, including direct soldering or wiring terminal connections, and features remote control channel support for switching the module on and off.

HGLRC 5-12V BEC step-down module supporting two-mode voltag전자 스위칭 — Figure 1: HGLRC 5-12V BEC Step-down Module overview, highlighting its two-mode voltage switching capability.

2. 제품 특징

Supports welding or wiring terminal connection for installation flexibility.
넓은 입력 voltag범위: 8.4V ~ 28V.
Dual output voltage modes: 5V and 12V.
High working current: Up to 2A for stable performance.
Remote control channel support for BEC module ON/OFF control.

3. 상자 안에 무엇이 들어있나요?

패키지 내용물을 확인하세요.

HGLRC 5-12V BEC Module ×1
Output cable ×1

Contents of the HGLRC 5-12V BEC package, showing the module and an output cable. — Figure 2: Product List - HGLRC 5-12V BEC module and included output cable.

4. 설정 및 설치

4.1 연결 옵션

The HGLRC 5-12V BEC module offers two primary methods for connection:

납땜: Direct soldering to the designated pads on the module.
배선 터미널 연결: Using the provided wiring terminals for a plug-and-play solution.

Comparison of soldering and wiring terminal connection methods for the BEC module. — Figure 3: Connection Methods - The module supports both direct soldering and wiring terminal connections.

4.2 배선도

Refer to the following diagram for proper wiring of the BEC module. Ensure correct polarity when connecting power inputs and outputs.

Detailed wiring diagram for the HGLRC 5-12V BEC module, showing input, output, and control connections. — Figure 4: Wiring Diagram. Connect BAT (8.4-28V) to the positive power input and GND to the negative power input. OUT+ and OUT- provide the regulated voltage. RX is for flight control LED/TX connection.

BAT (Positive Power Input): Connect your main battery (8.4V-28V, typically 2-6S LiPo) here.
GND (Negative Power Input): Connect the negative terminal of your battery here.
OUT+ (Positive Output): Provides the regulated 5V or 12V output. Connect to your electrical appliances (e.g., COB light strips).
OUT- (Negative Output): Connect the negative terminal of your electrical appliances here.
RX (Flight Control LED / TX): This pin is used for remote control channel integration to switch the BEC module on/off.

4.3 출력 볼륨tage Selection (5V / 12V Mode Switch)

The module supports switching between 5V and 12V output modes:

Default (Disconnected): When the solder joint (labeled "12V" on the board, near RX pin) is disconnected, the output voltage는 5V입니다.
12V Output (Connected): When the solder joint is connected (bridged with solder), the output voltage는 12V입니다.

항상 올바른 볼륨을 확인하세요.tage is selected for your connected devices to prevent damage.

Diagram illustrating the wide voltage input and dual voltage output modes (5V and 12V) of the BEC module, along with remote control support. — 그림 5: 볼륨tage Input/Output details. The module accepts 8.4-28V input and provides 5V or 12V output, controllable via remote channel.

5. 사용 설명서

Once the HGLRC 5-12V BEC module is correctly wired and the desired output voltage is selected, it will provide stable power to your connected components. The module also supports remote control functionality:

Remote Control ON/OFF: Connect the RX pin to a suitable remote control channel on your flight controller. This allows you to remotely switch the BEC module's output on or off, providing greater control over your drone's accessories. Consult your flight controller's manual for specific instructions on configuring a channel for this purpose.

6. 유지관리

To ensure the longevity and optimal performance of your HGLRC 5-12V BEC module, follow these maintenance guidelines:

깨끗하게 유지하십시오: Regularly inspect the module for dust, dirt, or debris. Use a soft, dry brush or compressed air to clean it.
습기를 피하세요: Protect the module from water and excessive humidity, which can cause short circuits and corrosion.
연결 검사: Periodically check all soldered joints and wiring terminal connections to ensure they are secure and free from damage. Loose connections can lead to intermittent power supply or component failure.
온도 관리: Ensure adequate airflow around the module, especially during operation, to prevent overheating.
조심스럽게 다루십시오: 모듈을 떨어뜨리거나 강한 충격을 가하지 마십시오. 내부 부품이 손상될 수 있습니다.

7. 문제 해결

If you encounter issues with your HGLRC 5-12V BEC module, refer to the following troubleshooting steps:

문제	가능한 원인	해결책
출력 볼륨 없음tage	잘못된 입력 볼륨tage. 배선이 느슨하거나 올바르지 않습니다. Module is switched off via remote control. 모듈 오류.	입력 볼륨 확인tage는 8.4V-28V 범위입니다. Check all connections for proper polarity and secure fit. Ensure the remote control channel is configured to turn the BEC on. If all else fails, the module may be faulty; contact support.
잘못된 출력 볼륨tage (e.g., 5V instead of 12V)	Incorrect solder joint configuration for voltag선택.	Check the solder joint for 5V/12V selection. Bridge it for 12V, leave disconnected for 5V.
모듈 과열	Excessive load on the output. 공기 흐름이 충분하지 않습니다.	Reduce the load on the 5V/12V output (ensure total current draw is below 2A). Improve ventilation around the module.

8. 사양

Detailed technical specifications for the HGLRC 5-12V BEC module:

매개변수	값
이름	HGLRC 5-12V BEC
입력 Voltage	8.4V – 28V (Supports 2-6S LiPo)
출력 볼륨tage	5V 2A / 12V 2A (Switchable)
최대 작동 전류	2A
치수	12.1mm × 21mm
무게	1.3g
재료	복합소재
추천연령	14세 이상
차량 유형에 따라	Airplanes (RC FPV Drones)

Image showing the HGLRC 5-12V BEC module and its key specifications: Name, Input Voltage, 출력 볼륨tage, Size, and Weight. — Figure 6: Product Specifications summary.

9. 사용자 팁

제공된 재에서 특정 사용자 팁을 사용할 수 없습니다.views or Q&A. However, general best practices for BEC modules include:

Always double-check your wiring before applying power to avoid short circuits or damage to components.
출력 볼륨을 확보하세요tage setting (5V or 12V) matches the requirements of the devices you are powering.
Consider using heat shrink tubing or conformal coating for added protection in harsh FPV environments.

10. 보증 및 지원

보증 정보, 기술 지원 또는 서비스 문의는 제조사 또는 구매처에 문의하십시오. 보증 청구를 위해서는 구매 증빙 자료를 보관하십시오.

	HGLRC Sector 5 V3 VTX FPV 레이싱 드론 매뉴얼 HGLRC Sector 5 V3 VTX FPV 레이싱 드론의 종합적인 사용 설명서입니다. 이 고급 레이싱 드론의 설정, 구성, 사양 및 문제 해결 방법을 다룹니다.
	HGLRC ELRS 2.4 RX-T 수신기 설명서 이 설명서는 제품 매개변수, 연결 다이어그램, 바인딩 단계, 사용 주의 사항을 포함하여 HGLRC ELRS 2.4 RX-T 수신기에 대한 자세한 정보를 제공합니다.
	HGLRC Sector25CR Sub250g HD FPV 레이싱 드론 매뉴얼 HGLRC Sector25CR Sub250g HD FPV 레이싱 드론에 대한 포괄적인 사용자 매뉴얼로, 제품 사양, 설정, 구성 및 문제 해결에 대한 내용을 담고 있습니다.
	HGLRC Sector4 FR 프리스타일 FPV 드론 HD 사용 설명서 - 설정 및 구성 가이드 HGLRC Sector4 FR 프리스타일 FPV 드론 HD의 설정 및 구성에 대한 종합 가이드입니다. 제품 사양, 인터페이스, 비행 컨트롤러 설정, 보정, 수신기 구성, VTX/DJI 배선, 비행 모드, OSD, LED 설정 및 문제 해결 방법을 다룹니다.
	HGLRC Petrel132 FPV 레이싱 드론 6S 사용자 설명서 HGLRC Petrel132 FPV 레이싱 드론 6S의 제품 사양, 인터페이스 설명, 설치 절차, 설정 및 문제 해결 가이드를 자세히 설명하는 종합 사용자 설명서입니다.
	HGLRC Zeus25 V2 AIO 비행 컨트롤러 매뉴얼 FPV 드론 애호가를 위해 제품 사양, 인터페이스 설명, 설정 절차, 구성 및 문제 해결 방법을 자세히 설명하는 HGLRC Zeus25 V2 AIO 비행 컨트롤러에 대한 포괄적인 사용자 매뉴얼입니다.

HGLRC HGLRC 5-12V BEC