HGLRC Rekon7 PRO LR 7-inch FPV Drone Frame Kit Instruction Manual

소개

This manual provides detailed instructions for the assembly, maintenance, and general use of the HGLRC Rekon7 PRO LR 7-inch 3K Carbon Fiber Frame Kit. Designed for FPV (First Person View) racing, freestyle, and long-range drones, this frame kit offers a robust and lightweight foundation for your custom build. Please read all instructions carefully before beginning assembly.

명세서

Recommended Parts (Not Included):

• Flight Control: Zeus F722
• 모터 : 2806.5
• ESC: Zeus 48-60A
• Camera: 19x19mm / 20x20mm
• Propeller: 7 inches
• Battery: 6S 1800-4200mAh

패키지 내용

The HGLRC Rekon7 PRO LR Frame Kit includes the following components:

• 1x 2mm top plate
• 1x 2mm base plate
• 1x 2mm mid plate
• 2x 6mm front arm
• 2x 6mm rear arm
• 2x 2mm rack protection board
• 2x 2mm camera side panel
• 2x 4mm Arm Reinforcement rod
• 2x M3*28mm black mesh aluminum column
• 4x M3*20mm black mesh aluminum column
• 2x M3*18mm black mesh aluminum pillar
• 4x M4*12 나사
• 4x M3*20 나사
• 4x M3*16 나사
• 4x M3*10 나사
• 8x M3*8 나사
• 4x M2*20 나사
• 1x M2*16 나사
• 1x M2*10 나사
• 2x M2*4 나사
• 1x M5 lock nut (red)
• 4x M3 셀프 잠금 너트
• 5x M2 셀프 잠금 너트
• 8x M3*8 shock-absorption balls
• 4x M2*4 shock-absorption balls
• 2x battery straps 20x250mm
• 1x Battery Anti-slip pad
• 1x TPU black GoPro holder mount
• 1x TPU black GPS mount
• 1x TPU black antenna mount
• 1x TPU black T-antenna mount
• 1x TPU black buzzer mount
• 1x TPU black DJI Air unit Block A
• 1x TPU black DJI Air unit Block B
• 1x TPU black DJI O3 holder mount
• 1x TPU black Camera converting seat

조립 설명서(설치)

Follow these steps carefully to assemble your Rekon7 PRO LR frame kit. Refer to the diagram for visual guidance.

1. Insert the frame bottom plate into the front and rear arms. Secure them using the M4*12mm screws.
2. Attach the middle plate. Use M3*8mm screws to fix the frame protection plates below the middle plate.
3. Position and fix the aluminum pillars (M3*10, M3*20, M3*28) to the corresponding locations on the middle plate.
4. Install the camera TPU conversion plate and the camera side plates.
5. Mount the various accessories: buzzer mount, T-type antenna mount, O3 VTX fixed mount, GPS mount, and antenna base.
6. Finally, install the GoPro mount and secure the top plate.

작동 지침

The HGLRC Rekon7 PRO LR is a frame kit and does not have standalone operating instructions. Once assembled with a flight controller, motors, ESC, camera, and other necessary components, it forms a complete FPV drone. Please refer to the individual manuals for your flight controller, ESC, and radio system for specific operating procedures, calibration, and flight guidelines.

General operating principles for FPV drones include:

• 비행 전 확인 사항: Always inspect all components for damage, loose connections, and correct propeller orientation before each flight.
• 배터리 안전: Use appropriate batteries (e.g., 6S 1800-4200mAh as recommended) and follow all battery charging and handling safety guidelines.
• 비행 환경: 드론은 사람, 동물, 장애물로부터 떨어진 탁 트인 공간에서 조종하십시오. 드론 비행에 관한 지역 규정을 숙지하십시오.
• 무장/해제: Understand the arming and disarming procedures for your flight controller to safely start and stop motors.
• First Flights: Begin with gentle flights in a controlled environment to familiarize yourself with the drone's handling characteristics.

유지

Regular maintenance will ensure the longevity and optimal performance of your Rekon7 PRO LR frame kit:

• 시각적 검사: After every crash or hard landing, thoroughly inspect the carbon fiber plates and arms for any cracks, delamination, or stress marks.
• 나사 조임 정도: Periodically check all screws and nuts for tightness. Carbon fiber frames can experience vibrations that may loosen fasteners over time. Apply thread-locker (e.g., blue Loctite) to metal-to-metal screws if necessary, but avoid on plastic or carbon fiber directly.
• 청소: Clean the frame with a soft, dry cloth. If necessary, use a slightly damp 순한 비누로 천을 적셔 닦은 후 완전히 말리십시오. 강한 화학 약품 사용은 피하십시오.
• TPU Parts: Inspect TPU mounts (GoPro, GPS, antenna, buzzer, camera) for wear, tears, or deformation. Replace if damaged to ensure components remain secure.
• Arm Reinforcement: Ensure the arm reinforcement rods are securely in place and free from damage.

문제 해결

This section addresses common issues related to the frame kit itself. For issues related to flight performance, electronics, or software, refer to the respective component manuals.

사용자 팁

• 다양한 용도: This frame kit is designed for FPV, RC, and drone applications, offering flexibility for various build types.
• 구성 요소 호환성: Always double-check the mounting hole patterns (flight controller, camera, motors) to ensure compatibility with your chosen electronics before assembly.
• 케이블 관리 : Plan your wiring carefully to keep cables tidy and secure within the frame, preventing interference with propellers or moving parts.
• Thread-locker: For metal screws into metal parts, a small amount of non-permanent thread-locker (e.g., blue Loctite) can prevent screws from vibrating loose. Avoid using it on plastic or carbon fiber.

보증 및 지원

For warranty information and technical support, please contact the seller or manufacturer directly. Keep your proof of purchase for any warranty claims. This frame kit is intended for experienced hobbyists due to the nature of FPV drone building and operation.