Kllisre X79 Motherboard User Manual

1. 서론

This manual provides detailed instructions for the installation, setup, operation, and maintenance of your Kllisre X79 Motherboard. Designed to support Intel Xeon LGA 2011 processors and DDR3 ECC RAM, this motherboard offers high compatibility and performance for various usage scenarios including gaming, household, and office applications. Please read this guide thoroughly before proceeding with any installation or configuration.

For a more detailed installation guide, you may refer to the official PDF document: Installation Guide: Intel Motherboard and Processor (PDF).

2. 안전수칙

Always observe the following safety precautions to prevent damage to components and ensure personal safety:

• 정전기 방전(ESD) 보호:
  • Always use anti-static measures, such as an anti-static wrist strap connected to a grounded object.
  • Touch grounded metal (e.g., the computer case) before handling components.
  • Avoid working on carpeted surfaces.
  • Keep components in anti-static bags until ready for use.
• 취급 구성품:
  • Never force components into place.
  • Handle components by their edges only; avoid touching contacts or socket pins.
  • 작업 공간을 깨끗하고 체계적으로 유지하십시오.
  • 적절한 도구를 사용하여 설치하십시오.
• 전원 공급 장치: This motherboard requires a powerful power supply. Ensure your power supply is at least 450W (brand power supply recommended) to adequately support the platform.

3. 사양

Below are the key specifications for the Kllisre X79 Motherboard:

메모: Due to different batches of factory materials (PCB boards, heat sinks, PCI-e and RAM slots, etc.), the appearance and color of the motherboard may vary. The picture is for reference only. This will not affect the use of the product.

4. 설정 가이드

This section outlines the steps for installing your Kllisre X79 Motherboard and its components.

4.1. 제품 다이어그램

4.2. 사전 설치 준비

필요한 도구:

• 안티 정전 손목 스트랩
• Thermal paste (if not pre-applied on cooler)
• Screwdriver (usually Phillips #2)
• 손전등 (더 잘 보이도록)

작업 공간 설정:

1. Choose a clean, well-lit, static-free environment.
2. Use an anti-static mat or work on a non-conductive surface.
3. Wear an anti-static wrist strap connected to a grounded object.
4. Keep all components in anti-static bags until ready for use.

구성 요소 검증:

• Confirm CPU socket compatibility (LGA 2011 for Intel Xeon processors).
• Verify motherboard BIOS supports the CPU model.
• Check RAM compatibility with the motherboard's Qualified Vendor List (QVL).

4.3. CPU 설치

1. CPU 소켓 열기: Locate the CPU socket on the motherboard. Gently lift the socket lever to the vertical position. Remove the socket cover if present.
2. CPU 정렬: Identify the triangle marker on the CPU (usually a gold corner). Match this with the triangle marker on the socket. For LGA sockets, the CPU has no pins; pins are in the socket.
3. Place CPU: Hold the CPU by its edges only (avoid touching contacts). Gently lower the CPU into the socket without force. Ensure the CPU sits flat with no gaps.
4. 보안 소켓: Carefully lower the socket lever. Press down until it clicks into place. Verify the CPU is securely locked.

중요 참고 사항:

• Never force the CPU into the socket.
• Do not touch CPU contacts or socket pins.
• Handle the CPU by its edges only to prevent damage.

4.4. CPU 쿨러 설치

Stock Cooler Installation:

1. 열 페이스트 적용: Apply a pea-sized amount of thermal paste to the center of the CPU. If using pre-applied paste, skip this step.
2. 쿨러 위치: Align the cooler with the mounting holes. Ensure the retention mechanism matches the socket type.
3. 안전한 쿨러: Attach clips or screws in a diagonal pattern. Apply even pressure to spread the thermal paste.
4. 팬 연결: Connect the CPU fan cable to the CPU_FAN header on the motherboard. Ensure cable routing does not interfere with other components.

Aftermarket Cooler Installation:

• Follow manufacturer-specific instructions for your aftermarket cooler.
• May require backplate installation.
• Check for clearance with RAM and other components.

4.5. RAM 설치

1. 슬롯 식별: Refer to the motherboard manual for optimal slot configuration. Usually, start with slot A2 for a single module.
2. Align Notch: Match the RAM module's notch with the slot key. Ensure correct orientation.
3. RAM을 삽입하세요: Apply firm, even pressure on both ends of the module. The modules should click into place. Verify that the retention clips snap shut.

Configuration Tips:

• For dual-channel configuration, install modules in matching colored slots.
• Check the maximum supported frequency in BIOS.

4.6. 마더보드 장착

1. I/O 쉴드를 설치하세요: Insert the I/O shield into the rear of the case. Ensure proper alignment with the ports.
2. Position Standoffs: Install brass standoffs in the case, matching the motherboard holes. Use only necessary standoffs to avoid shorts.
3. 마더보드 장착: Carefully lower the motherboard onto the standoffs.
4. 나사로 고정: Align I/O ports with the shield and secure the motherboard with screws (do not overtighten).

4.7. 전원 연결

Essential Connections:

• 24-pin ATX power: Main motherboard power.
• 8-pin CPU power: CPU VRM power (usually near the CPU socket).
• PCIe power: For graphics card (if applicable).
• SATA power: For storage devices.
• Peripheral power: For additional components.

연결 팁:

• Connect all required power cables before powering on the system.
• Ensure all connectors are fully seated.
• Verify no loose cables near fans.

5. 사용 설명서

5.1. Post-Installation Checks (First Power-On)

1. 시각적 검사:
   • 모든 구성 요소가 안전하게 설치되었는지 확인하십시오.
   • Check for any loose screws or tools inside the case.
   • Ensure cables are clear of moving parts.
   • Confirm all power connectors are attached.
2. 첫 번째 전원 켜기:
   • Connect a monitor to the graphics card (not directly to the motherboard if a dedicated GPU is installed).
   • Press the power button and observe the system.
   • Listen for POST beep codes (refer to your case/BIOS manual for code meanings).
   • Check that the CPU fan is spinning.
3. BIOS 구성:
   • Enter BIOS/UEFI setup (usually by pressing Del or F2 key during boot).
   • Verify that the CPU and RAM are detected correctly.
   • Check temperatures and voltag에스.
   • Enable XMP/DOCP for RAM overclocking if desired.
   • Set the boot order for your operating system drive.

6. 유지관리

정기적인 유지보수는 마더보드의 수명과 최적의 성능을 보장하는 데 도움이 됩니다.

• Clean dust from components regularly using compressed air.
• Reapply thermal paste to the CPU every 1-2 years for optimal cooling.
• Update BIOS for better compatibility and performance (refer to manufacturer's web대지).
• Monitor temperatures during operation to prevent overheating.

7. 문제 해결

If you encounter issues, consider the following troubleshooting tips:

• No POST (Power-On Self-Test):
  • 모든 전원 연결(24핀 ATX, 8핀 CPU)을 확인하세요.
  • Verify the CPU is properly seated in its socket.
  • Ensure RAM modules are fully inserted and in the correct slots.
  • CPU, RAM 1개, 내장 그래픽이 없는 경우 GPU 등 필수 구성 요소만 사용하여 부팅해 보세요.
  • Listen for beep codes and consult your BIOS manual for their meaning.
• 시스템 불안정/충돌:
  • CPU와 GPU 온도를 확인하세요.
  • 모든 드라이버가 최신 상태인지 확인하세요.
  • RAM 모듈을 개별적으로 테스트하십시오.
  • 전원 공급 장치를 확인하십시오.tage는 모든 구성 요소에 충분합니다.
• 일반적인 문제:
  • Consult the motherboard manual for specific error codes or troubleshooting steps.
  • 제조업체를 방문하세요 website for support and updated drivers/BIOS.
  • Check community forums for similar issues and solutions.

8. 사용자 팁

제공된 재에서 특정 사용자 팁을 사용할 수 없습니다.views or Q&A content at this time. Always ensure compatibility of all components (CPU, RAM, GPU, PSU) before installation.

9. 보증 및 지원

Your Kllisre X79 Motherboard comes with a 1년 보증 from the date of purchase. For any issues or support, please refer to the following resources:

• 공식 사용자 매뉴얼(PDF): PDF 다운로드
• 제조업체의 Web대지: Visit the Kllisre official website for updated drivers, BIOS, and support information.
• 기술 지원: Contact Kllisre technical support if needed.