1. 제품 오버view
JBL Stage3 Gen2 68CF 6.5-inch 2-Way Component Car Speakers are engineered to deliver high-quality audio performance in your vehicle. This component system includes woofers, tweeters, and external crossovers, designed for a balanced and dynamic sound experience.
주요 특징
- Patented Plus One Woofer Cone: Features a larger cone surface area for higher sensitivity and deeper bass.
- Glass Fiber Reinforced Cone: Infused with 10% glass fiber and laser-etched for structural rigidity, producing powerful, resonant bass.
- Edge-Driven Silk Dome Tweeter: Provides a broader, smoother high-frequency response without distortion, even at high volumes.
- True 4-Ohm Impedance Design: Maximizes power output from your head unit or amplifier by compensating for system resistance.
- Complete Component Kit: Includes two woofers, two silk dome tweeters, and two inline crossovers for a comprehensive audio upgrade.
환경적 책임
JBL is committed to environmental sustainability. The Stage3 Gen2 speakers incorporate post-consumer recycled plastic materials and PVC-free wiring. The packaging utilizes soy-based inks, reflecting a dedication to environmentally conscious innovation.
그림 1: 전면 view JBL S의tage3 Gen2 68CF 6.5-inch woofer, showcasing its carbon fiber camouflage cone design and JBL logo.
Figure 2: An illustrative image highlighting the JBL Stage3 Gen2 68CF speaker's key features, including powerful sound, upgrade potential, and separate tweeters for clearer audio.
2. 상자 안에 무엇이 들어있나요?
내용물을 조심스럽게 풀어서 모든 품목이 들어 있는지 확인하세요.
- 2개의 스피커(우퍼)
- 2x 0.75-inch Tweeters
- 2x Threaded Flush-mount Adapters for tweeters
- 2x Plastic Locking Nuts for tweeters
- 2x Crossover Boxes
- 8x Screws for mounting
- 8x Spade Clips for connections
- 1x Mini Owner's Manual (OM)
- 2x 폼 개스킷
- 2x Logo Badges
그림 3: 클로즈업 view of the JBL silk dome tweeter, featuring a protective grille and the JBL logo, designed for clear high-frequency sound reproduction.
Figure 4: The JBL crossover box, which separates audio frequencies for optimal delivery to the woofer and tweeter, ensuring clear and balanced sound.
3. 설정 및 설치
Professional installation is recommended. If performing a DIY installation, follow these guidelines carefully.
3.1 안전 정보
- 단락 및 손상을 방지하기 위해 전기 작업을 시작하기 전에 항상 차량 배터리의 음극 단자를 분리하십시오.
- 눈 보호 장비를 포함한 적절한 안전 장비를 착용하세요.
- Ensure all wiring is properly insulated and secured to prevent chafing or damage.
3.2 필요한 도구
- 드라이버(십자 드라이버 및 일자 드라이버)
- 와이어 스트리퍼/크림퍼
- (새로운 장착 구멍이 필요한 경우) 드릴로 구멍을 뚫으십시오.
- 줄자
- 패널 제거 도구
- 전기 테이프 또는 열 수축 튜브
3.3 Speaker Placement and Fitment
Before installation, measure your vehicle's speaker openings and mounting depth to ensure compatibility. The JBL Stage3 Gen2 68CF speakers are designed for 6.5-inch (165mm) cutouts.
Figure 5: A detailed guide on how to measure for car speaker fitment, including cone diameter, mounting depth, and outer diameter, to ensure proper installation.
Figure 6: Technical diagram showing the precise dimensions of the JBL Stage3 68CF woofer and tweeter, essential for accurate installation and fitment.
3.4 장착 지침
- 스피커 위치 확인: Carefully remove door panels or other trim to access the factory speaker locations.
- 오래된 스피커 제거: Disconnect and remove any existing speakers.
- 마운트 우퍼스: Place the new JBL woofers into the speaker openings. Use the provided screws to secure them firmly. Ensure the foam gasket is used for a tight seal.
- 트위터 마운트: The tweeters can be flush-mounted or surface-mounted. Choose the appropriate adapter and secure them in your desired location (e.g., dashboard, door pillar).
- Install Crossovers: Find a secure, dry location for the crossover boxes, away from moisture and excessive heat.
Figure 7: The JBL Stage3 Gen2 6.5-inch woofer professionally installed within a car door panel, demonstrating proper fit and wiring connections.
Figure 8: A JBL tweeter seamlessly integrated into a car's door panel, illustrating a clean and functional installation.
3.5 배선도
Connect the speakers to the crossovers, and then the crossovers to your head unit or amplifier. Refer to the diagram below for typical connections. Ensure correct polarity (+/-) for all connections.
- 연결하다 입력 terminals of the crossover to the speaker output of your head unit or amp리퍼.
- 연결하다 WF (Woofer) terminals of the crossover to the JBL 6.5-inch woofer.
- 연결하다 TW (Tweeter) terminals of the crossover to the JBL 0.75-inch tweeter.
- Secure all connections using spade clips or by soldering and insulating with electrical tape or heat shrink tubing.
메모: Specific wiring colors may vary. Always match positive (+) to positive (+) and negative (-) to negative (-).
4. 운영
4.1 초기 전원 켜기
After installation, reconnect the car battery. Turn on your car's audio system. Start with the volume low and gradually increase it to ensure all speakers are functioning correctly and without distortion.
4.2 오디오 설정
- Balance and Fader: Adjust these settings on your head unit to ensure sound is evenly distributed throughout the vehicle.
- 이퀄라이저(EQ): Use your head unit's equalizer to fine-tune the sound to your preference. Start with a flat EQ and make small adjustments.
- 게인 설정: 외부를 사용하는 경우 amplifier, ensure the gain is set correctly to prevent clipping and speaker damage. Consult your amp앰프의 게인 조정 절차는 설명서를 참조하십시오.
4.3 적응 기간
Allow a break-in period of approximately 20-30 hours of normal listening at moderate volumes. This allows the speaker components to loosen up and achieve their optimal sound performance.
5. 유지관리
5.1 청소
To maintain the appearance and performance of your speakers, periodically wipe them with a soft, dry cloth. Avoid using harsh chemicals, abrasives, or excessive moisture, which can damage the speaker cones or grilles.
5.2 검사
Occasionally inspect the speaker connections and mounting hardware to ensure they remain secure. Loose connections can lead to poor sound quality or intermittent audio.
6. 문제 해결
JBL S 사용 중 문제가 발생하면tage3 Gen2 68CF speakers, refer to the following common problems and solutions:
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 하나 이상의 스피커에서 소리가 나지 않습니다. | 느슨하거나 잘못된 배선 헤드 유닛의 퓨즈가 끊어졌습니다.amp리퍼 Faulty speaker or crossover | Check all wiring connections for proper polarity and tightness. Ensure the head unit or amplifier is powered on. Check fuses. Test speakers individually if possible. |
| 왜곡되거나 잡음이 섞인 소리 | Overdriven signal (clipping) 느슨한 배선 손상된 스피커 콘 잘못된 amp리파이어 게인 설정 | 볼륨을 줄이세요. 확인하세요 amplifier gain settings. Inspect speaker cones for physical damage. Verify all wiring connections are secure. |
| 음향이 고르지 않거나 음질이 좋지 않음 | Incorrect balance/fader settings One speaker not functioning optimally | Adjust balance and fader settings on your head unit. Refer to "No sound" troubleshooting if one speaker is completely silent. |
7. 사양
JBL S의 상세 기술 사양tage3 Gen2 68CF 6.5-inch 2-Way Component Car Speakers:
| 특징 | 사양 |
|---|---|
| 상표 | 제이비엘 |
| 모델명 | JBL 에스TAGE3 GEN2 68CF |
| 모델 번호 | JBLSPKS368CF |
| 스피커 유형 | 2-Way Component Set |
| Woofer Driver Diameter | 6.5인치(16.5센티미터) |
| Tweeter Driver Diameter | 0.75인치(19밀리미터) |
| 스피커 최대 출력 전력 | 760와트(최대) |
| RMS 전원 | 95와트(RMS) |
| 임피던스 | 4옴 |
| 주파수 응답 | 55Hz - 20kHz |
| 신호 대 잡음 비율 | 91데시벨 |
| 장착 유형 | 플러시 마운트 |
| 인클로저 재료 | 금속 플라스틱 |
| 색상 | Carbon Fiber Camouflage |
| 입력 Voltage | 12볼트(DC) |
| 품목 치수(D x W x H) | 6.2D x 15.8W x 15.8H 센티미터 |
| 품목 무게 | 1킬로그램 |
| 방수 레벨 | 방수가 되지 않음 |
| 제품의 특정 용도 | Car-Audio Systems |
Figure 9: The JBL Stage3 Gen2 68CF speaker with key specifications such as RMS power, maximum power, frequency response, sensitivity, and impedance clearly displayed.
8. 보증 및 지원
8.1 보증 정보
JBL products are designed for durability and performance. This product typically comes with a manufacturer's warranty. For specific warranty terms and conditions, please refer to the warranty card included in your product packaging or visit the official JBL website. The EU Spare Part Availability Duration is 2 years.
8.2 고객 지원
For technical assistance, troubleshooting beyond this manual, or warranty claims, please contact JBL customer support. You can find contact information on the official JBL web사이트 또는 공인 딜러를 통해 구매하세요.
방문하세요 Amazon의 JBL 스토어 자세한 내용은.
