Treeligo Portable Propane Water Heater (Model GWT000.04) Instruction Manual

1. 서론

Thank you for choosing the Treeligo Portable Propane Water Heater. This device is designed to provide instant hot water for various outdoor activities such as camping, hiking, and cleaning. It features a compact design, a built-in rechargeable battery, and multiple safety protections to ensure a reliable and convenient experience.

Please read this manual thoroughly before operating the water heater to ensure proper use and to prevent potential hazards.

2. 안전 정보

여러분의 안전이 최우선입니다. 다음 지침을 항상 준수하십시오.

• 야외 사용 전용: This water heater is designed for outdoor use in well-ventilated areas. Never operate it indoors or in enclosed spaces due to the risk of carbon monoxide poisoning.
• 프로판 안전: Ensure all gas connections are secure and leak-free before operation. Use only approved propane cylinders and regulators. Store propane cylinders in a well-ventilated area away from ignition sources.
• 물의 온도: The unit can heat water up to 149°F (65°C). Exercise caution to avoid scalding. Always test water temperature before use, especially for children or individuals with sensitive skin.
• 물의 공급원: Use clean water only. Do not use the pump with flammable liquids or corrosive chemicals.
• 배터리 충전: Charge the built-in 4500mAh battery using the provided charger. Do not use unapproved chargers. Ensure the battery is fully charged for optimal performance and health.
• 6-in-1 Safety Protection: The unit includes temperature control, windproof protection, pump running dry protection, tilt protection, overheat protection (automatic shut-off at 185°F/85°C), and circuit protection. Do not attempt to bypass or modify these safety features.
• 어린이와 애완동물: Keep children and pets away from the operating water heater.
• 저장: When not in use, disconnect the propane tank and store the unit in a dry, safe place.

그림 1: 이상view of the 6-in-1 safety protection features.

3. 패키지 내용

패키지에 모든 품목이 포함되어 있는지 확인하세요.

• 1 x Treeligo Portable Water Heater
• 1 x Submersible Pump Assembly (6.5 feet hose)
• 1 x Shower Head Set (5 feet hose)
• 1 x Water Inlet Connection
• 1 x Gas Regulator
• 1 x Charger (4 feet cable)
• 1 x 사용자 설명서

Figure 2: All included components of the Treeligo Portable Water Heater.

4. 설정 지침

Follow these steps to set up your portable water heater:

1. 단위 위치: Place the water heater on a stable, level surface in a well-ventilated outdoor area.
2. 급수구를 연결하세요: Screw the blue water inlet connection securely into the designated port on the unit.
3. 펌프를 연결하십시오: Plug the black power cable of the pump into the 'WATER PUMP INTERFACE' port. Connect the pump water hose to the water inlet connection.
4. 수중 펌프: Place the submersible pump fully into a clean water source (e.g., a bucket or container). Ensure the pump is completely submerged before operation.
5. 샤워 호스 연결: Connect the shower hose to the red outlet port on the unit.
6. Connect Gas Regulator: Attach the gas regulator to your propane cylinder, then connect the other end of the regulator to the gas inlet at the back of the water heater. Ensure all gas connections are tight.
7. 전원 켜기 메인 스위치: Locate the small black main power switch on the bottom of the machine and turn it to the 'ON' position.
8. Power On Display Panel: Tap the power button on the display panel to turn on the unit. Check the battery level on the display. If the battery is low, connect the charger to the 'CHARGING INTERFACE' port on the front of the unit.

Figure 3: Step-by-step visual guide for initial setup.

5. 사용 설명서

Once set up, operate your water heater as follows:

5.1 제어판 이상view

Figure 4: Intelligent Real-Time Display and Control Panel.

• 배터리 수준: 배터리 잔량을 나타냅니다.
• 입구 수온: Displays the temperature of the incoming water.
• Water Flow Status: Shows if water is flowing.
• 펌프 상태: Indicates if the pump is active.
• 온 / 오프 스위치: Main power button for the display panel.
• Output Water Temperature: Displays the temperature of the heated water.
• 배터리 용량tage: 현재 배터리 용량을 표시합니다.tage.
• Burner Status: Indicates if the burner is active.
• Burner Switch: Activates or deactivates the propane burner.
• 펌프 스위치: Activates or deactivates the water pump.
• 수온 조절 손잡이: Adjusts the desired output water temperature (Low to High).

5.2 온수기 시작

1. Ensure all setup steps are completed and connections are secure.
2. Turn on the main power switch on the bottom of the unit.
3. Press the ON/OFF switch on the display panel. The unit will automatically enter shower mode, and the showerhead icon will light up.
4. 를 누르세요 펌프 켜기/끄기 button to start the water pump. Water will begin to flow.
5. 조정하다 Water Temperature Control Knob to your desired temperature. The burner will ignite automatically to heat the water.
6. The display will show the inlet and output water temperatures in real-time.

5.3 Adjusting Water Flow Modes

The shower head offers three adjustable water flow modes:

• Jet Stream: 집중적이고 강력한 흐름.
• 표준 모드: A balanced, everyday shower stream.
• 강우 모드: A gentle, wide spray.

Rotate the shower head nozzle to switch between these modes.

Figure 5: Three adjustable water flow modes on the shower head.

5.4 배터리 작동 및 충전

The built-in 4500mAh battery provides up to 100 minutes of continuous use on a full charge. It charges to 80% in 90 minutes and 100% in 3 hours. The unit supports charging while in use. For optimal battery health, always charge to 100% when possible.

6. 유지관리

Regular maintenance ensures the longevity and safe operation of your Treeligo Portable Water Heater:

• 청소: After each use, drain any remaining water from the unit and hoses. Wipe down the exterior with a damp 천. 연마성 세척제나 용매를 사용하지 마십시오.
• 저장: Store the unit in a dry, protected area when not in use. Disconnect the propane tank and ensure all hoses are properly coiled.
• 배터리 관리 : 장기간 보관할 경우 배터리를 약 50~70%까지 충전하고 3~6개월마다 재충전하여 과방전을 방지하십시오.
• 연결 검사: Periodically check all water and gas connections for wear, damage, or leaks. Replace any damaged components immediately.
• 겨울철 : In freezing temperatures, ensure all water is completely drained from the unit and hoses to prevent damage from ice expansion.

7. 문제 해결

문제가 발생하면 다음의 일반적인 문제와 해결 방법을 참조하세요.

Q1: My water pump isn't working at all and isn't pumping any water. What should I do?

A:

1. Power Switch Location: The small black switch on the bottom of the machine is the main power switch for the entire device. Ensure it is turned ON.
2. 배터리 잔량 확인: If the indicator light or screen on the control panel does not light up after pressing the power button, the built-in battery is low. Connect the power adapter to charge it first.
3. 충전 참고 사항: When the device is out of power, neither the water pump nor the heating function will start. This is the most common reason why the device does not work.

Figure 6: Main power switch and display panel for troubleshooting pump issues.

Q2: I can't tell which port is for charging and which is for power output. What should I do?

A: Refer to the image below for the correct wiring method.

1. Plug the water pump's power cord into the port labeled "WATER PUMP INTERFACE."
2. Connect the water inlet hose to the threaded fitting labeled "Water Inlet" at the bottom.

중요 참고 사항: Never plug the pump's power cord into the charging port. The charging port is only for charging the device; the pump will not work at all if plugged in there.

Figure 7: Correct port identification for pump and charging.

Q3: I just received the unit, and the pump isn't working when I use it for the first time. Is this normal?

A: Ensure correct connections as follows:

1. Plug the power adapter into the 'CHARGING INTERFACE' port on the device to charge.
2. The red port labeled "Water output" or "Water pump port" is the power supply port for the water pump; do not plug a charger into it.

중요 참고 사항:

• To charge the device: Plug into the 'CHARGING INTERFACE' on the front.
• To run the water pump: Plug into the 'WATER PUMP INTERFACE' on the side.
• To connect water hoses: Connect the hose to the 'Water output' (out) on the front and the 'Water inlet' (in) on the side.

Figure 8: Correct port usage for charging and pump operation.

Q4: The equipment is powered on and the wiring is correct, but the pump still won't start. What could be the problem?

A:

1. 아이콘 설명: When the showerhead icon is lit on the display, it indicates that the device is in "Shower Mode." Pressing the 펌프 켜기/끄기 button at this time will activate the pump to supply water.
2. How to turn on shower mode: First, press the power button on the far left to turn on the device. It will automatically enter shower mode, and the showerhead icon will light up. Then press the 펌프 켜기/끄기 button to start the pump, and you can take a shower as usual.
3. Additional tip: If the icon isn't lit, the pump won't start. You can check to see if the mode is set correctly or if the device is plugged in.

Figure 9: Shower mode icon on the display panel.

8. 사양

9. 보증 및 지원

Treeligo products are manufactured to high-quality standards. For warranty information, please refer to the specific warranty card included with your product or contact Treeligo customer support.

For technical assistance, troubleshooting, or to inquire about replacement parts, please visit the official Treeligo store or contact their customer service department. Keep your purchase receipt and model number (GWT000.04) handy when contacting support.

Treeligo Store: Visit the Treeligo Store on Amazon