1. 제품 오버view
The SINOTIMER SVP719 is a 3-in-1 adjustable voltage surge protector relay designed for single-phase 120VAC systems. It integrates over-voltag전자 보호, 언더볼tage protection, current limiting, and energy metering functions. This device features three digital LED displays for real-time monitoring of voltage, current, and energy consumption (kWh). It is equipped with automatic recovery capabilities, ensuring electrical equipment protection by cutting off power during abnormal conditions and automatically restoring it when parameters return to normal. The unit is designed for easy installation on a universal DIN 35mm standard guide rail.
앞쪽 view of the SINOTIMER SVP719 Adjustable Voltag서지 보호기.
Detailed diagram of the SVP719 showing displays and controls.
2. 안전 정보
설치 및 작동 전에 모든 안전 지침을 주의 깊게 읽으십시오. 지침을 따르지 않으면 감전, 화재 또는 심각한 부상이 발생할 수 있습니다.
- 설치는 자격을 갖춘 사람만 수행해야 합니다.
- Ensure the main power supply is disconnected before any wiring or maintenance.
- 올바른 볼륨 확인tage and current ratings for your application.
- 물기가 있거나 습기가 있는 곳에서 장치를 작동하지 마십시오.amp 정황.
- Do not attempt to repair or modify the device. Contact qualified service personnel.
3. 설정 및 설치
The SVP719 is designed for easy installation on a standard 35mm DIN rail. Follow the wiring diagram below for proper connection.
3.1 장착
Mount the device securely onto a 35mm DIN rail within an electrical enclosure.
3.2 배선 연결
Connect the device according to the provided wiring diagram. Ensure all connections are tight and secure to prevent loose contacts and potential hazards.
- N Input: Connect the neutral wire from the power source.
- L Input: Connect the live wire from the power source.
- N Output: Connect the neutral wire to the load.
- L Output: Connect the live wire to the load.
Wiring Diagram for SVP719.
4. 사용 설명서
The SVP719 features three LED displays and four control buttons for monitoring and configuration.
4.1 LED 디스플레이
- 권tage 디스플레이(V): 실시간 볼륨을 보여줍니다tag회로의 전자.
- 현재 디스플레이(A): Shows the real-time current flowing through the circuit.
- Kilowatt-hour Display (kWh): Shows the accumulated energy consumption.
4.2 제어 버튼
- 설정 버튼: Used to enter the parameter setting mode and cycle through different adjustable parameters.
- 위쪽 화살표 버튼: Used to increase the value of a selected parameter.
- 아래쪽 화살표 버튼: Used to decrease the value of a selected parameter.
- 켜기/끄기 버튼: Used to manually turn the power supply to the load ON or OFF.
4.3 Manual ON/OFF Operation
를 누르세요 켜짐/꺼짐 button to manually switch the power to the connected load. The display will show 'OFF' when power is disconnected and 'ON' when connected.
4.4 Kilowatt-hour (kWh) Reset
To reset the accumulated Kilowatt-hour (kWh) reading, press the 아래쪽 화살표 그리고 세트 buttons simultaneously. The kWh display will reset to 000.0.
This video demonstrates the key features and operation of the SINOTIMER SVP719, including parameter adjustment, over-voltag전자 보호, 언더볼tage protection, and manual ON/OFF control.
5. 매개 변수 설정
The SVP719 allows for adjustment of various protection parameters. All parameters are adjustable within specified ranges.
5.1 Entering Setting Mode
를 누르고 계세요 세트 button for approximately 3 seconds to enter the parameter setting mode. The first adjustable parameter will appear on the display.
5.2 Cycling Through Parameters
Once in setting mode, short press the 세트 button to cycle through the parameters sequentially. Each press will display the next parameter.
5.3 Adjusting Parameter Values
When a desired parameter is displayed, use the 위쪽 화살표 그리고 아래쪽 화살표 buttons to adjust its value. The display will flash while adjusting.
5.4 Saving Settings and Exiting
After adjusting a parameter, wait for approximately 5 seconds without pressing any button. The device will automatically save the new setting and exit the setting mode, returning to normal operation.
5.5 조정 가능한 매개변수
- U> (Over-voltage Protection Value): 상한 볼륨을 설정합니다tage limit. If the voltage exceeds this value, the protector will trip.
- U< (Under-voltage Protection Value): 낮은 볼륨을 설정합니다tage limit. If the voltage drops below this value, the protector will trip.
- I> (Over-current Protection Value): Sets the maximum current limit. If the current exceeds this value, the protector will trip.
- t-on (Fault Recovery Delay Time): Sets the delay before the device automatically reconnects after a fault (over/under voltage, over-current) has cleared.
- t-off (Reset/Start Delay): Sets the delay for initial power-on or manual reset.
- CAL-A (Current Calibration): Allows for fine-tuning of the current measurement.
- CAL-V (Voltage 교정): Allows for fine-tuning of the voltag측정.
- CLP (Clear kWh): Resets the energy consumption counter.
6. 보호 기능
The SVP719 provides robust protection for your electrical equipment.
6.1 오버볼tage 보호
When the circuit voltage는 설정된 over-vol을 초과합니다.tage protection value (U>), the protector will instantaneously cut off the power supply to prevent damage to connected devices. The display will indicate an over-voltag조건.
6.2 언더 볼륨tage 보호
If the circuit voltage가 설정된 under-vol 아래로 떨어집니다.tage protection value (U<), the protector will immediately disconnect the power. The display will indicate an under-voltag조건.
6.3 과전류 보호
Should the current drawn by the load exceed the set over-current protection value (I>), the device will trip and cut off power to protect the circuit and load.
6.4 자동 복구
After a fault condition (over-voltage, 언더볼륨tage, or over-current) has been detected and the power supply is cut off, the SVP719 will continuously monitor the circuit. Once the voltage and current return to normal operating ranges for the duration of the set recovery delay time (t-on), the protector will automatically restore power to the load.
7. 유지관리
To ensure optimal performance and longevity of your SVP719, follow these simple maintenance guidelines:
- 기기에 물리적 손상이나 연결 불량 등의 징후가 있는지 정기적으로 점검하십시오.
- 기기를 깨끗하게 유지하고 먼지와 이물질이 묻지 않도록 하십시오. 마른 부드러운 천으로 닦아주세요.
- 연마성 세척제나 용제를 사용하지 마십시오.
- 기기의 과열을 방지하기 위해 기기 주변에 적절한 환기가 이루어지도록 하십시오.
8. 문제 해결
If you encounter issues with your SVP719, refer to the following common problems and solutions:
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 장치 전원이 켜지지 않음 | No input power; incorrect wiring | Check main power supply; verify wiring connections as per diagram. |
| 정전이 자주 발생합니다 | 권tage/current outside set limits; sensitive settings | 실제 볼륨을 확인하세요tage/current; adjust protection parameters (U>, U<, I>) to appropriate levels for your load. |
| Device does not recover automatically | Fault condition still present; recovery delay too long | 볼륨을 확보하세요tage/current has returned to normal; check and adjust 't-on' recovery delay setting. |
| kWh reading is inaccurate | 교정 필요 | Perform current and voltage calibration (CAL-A, CAL-V) if you have a reference meter. |
9. 사양
Technical specifications for the SINOTIMER SVP719-1-63A model:
Technical specifications printed on the device casing.
| 특징 | 사양 |
|---|---|
| 상표 | 시노타이머 |
| 모델 번호 | SVP719-1-63A |
| 권tage | 120 볼트 AC |
| 최대 전류 | 63 Amps |
| 콘센트 수 | 1 |
| 특징 | Surge Protection, Over-voltage 보호, 저용량tage Protection, Current Limiting, Energy Metering |
| 전원 플러그 유형 | A형 - 2핀 (북미식) |
| 설치 | DIN 35mm Standard Guide Rail |
| 한국어: | 607606586190 |
10. 보증 및 지원
The SINOTIMER SVP719-1-63A comes with a 1년 제조사 보증.
For technical support, warranty claims, or further assistance, please contact SINOTIMER customer service through their official channels or the retailer from whom the product was purchased. Please have your product model number (SVP719-1-63A) and purchase details ready when contacting support.