OSD Audio IWS88 In-Wall Subwoofer and SMP800 Amplifier Bundle Instruction Manual

1. 소개 및 이상view

This manual provides detailed instructions for the installation, operation, and maintenance of your OSD Audio IWS88 In-Wall Subwoofer and SMP800 Class D Mono Amplifier bundle. This system is designed to deliver powerful, deep bass for home theater and audio systems while integrating discreetly into your living space.

이 번들에는 다음이 포함됩니다.

• IWS88 In-Wall Subwoofer: A passive subwoofer featuring dual 8-inch drivers, designed for flush installation within a wall. It handles up to 350W of power.
• SMP800 Class D Mono Amp정수기: An 800W amplifier specifically designed to power passive subwoofers. It features Class D efficiency, variable crossover, phase control, auto-on sensing, and versatile input options (RCA/LFE, Speaker Level, 12V Trigger).

최적의 성능과 안전을 위해 설치 및 사용 전에 본 설명서를 꼼꼼히 읽어 주십시오.

2. 안전 지침

Please observe the following safety precautions to prevent damage to the unit and ensure user safety:

• 전기 안전: 항상 연결 해제 amplifier from the power outlet before performing any service or installation. Ensure proper grounding. Do not expose the amp비 또는 습기에 대한 liifier.
• 통풍: 그만큼 amplifier requires adequate ventilation. Do not block any ventilation openings. Install the amplifier in a location with sufficient airflow.
• 놓기: Install the in-wall subwoofer and amplifier in locations free from excessive heat, humidity, dust, or vibration. Keep the amplifier away from direct sunlight and heat sources.
• 배선: Ensure all wiring connections are secure and correct before powering on the system. Incorrect wiring can cause damage to the equipment.
• 서비스: 이 제품을 직접 수리하려고 하지 마십시오. 모든 서비스는 자격을 갖춘 서비스 담당자에게 문의하십시오.

3. 패키지 내용

패키지에 모든 품목이 들어 있는지 확인하세요.

• OSD Audio IWS88 In-Wall Subwoofer
• OSD Audio SMP800 Class D Mono Amp리퍼
• Removable Grille for IWS88 Subwoofer
• Power Cable for SMP800 Amp리퍼
• 사용 설명서(본 문서)
• Mounting Hardware (integrated dog-ear clamps for subwoofer)

4. 설정 및 설치

4.1 In-Wall Subwoofer Installation (IWS88)

1. 위치를 선택하십시오 : Select a suitable wall location, ensuring no obstructions like electrical wiring, plumbing, or studs are present. Use a stud finder to locate studs and avoid them.
2. 절단된 오프닝: Use the provided cutout template (if included, otherwise measure carefully) to mark the opening on the wall. Carefully cut the opening using a drywall saw.
3. 스피커 와이어 실행: Route appropriate gauge speaker wire (e.g., 14-gauge or 12-gauge) from the amplifier location to the subwoofer opening. Leave enough slack for connections.
4. 스피커선 연결: Connect the speaker wires to the spring-loaded terminals on the IWS88 subwoofer. Ensure correct polarity (+ to + and - to -).

이미지: 앞면 view of the IWS88 In-Wall Subwoofer with the grille removed, revealing the dual 8-inch drivers and the speaker wire terminals.

이미지: 각도 view of the IWS88 In-Wall Subwoofer, illustrating its internal components, mounting clamps, and speaker terminals.

5. Mount Subwoofer: Carefully insert the subwoofer into the wall opening. Tighten the mounting screws (usually located on the front baffle) which will engage the dog-ear clamps to secure the subwoofer to the drywall. Do not overtighten.
6. 그릴 부착: Once the subwoofer is securely mounted, attach the magnetic grille to the front of the subwoofer.

이미지: 앞면 view of the IWS88 In-Wall Subwoofer with the magnetic grille in place, demonstrating its flush and discreet appearance.

4.2 Amplifier Connection (SMP800)

Position the SMP800 amplifier in a well-ventilated area, preferably near your AV receiver or audio source.

Image: Rear panel of the SMP800 Class D Mono Amplifier, highlighting its input and output connections.

1. 오디오 입력 연결:
   • RCA/LFE Input: For most home theater receivers with a dedicated subwoofer output (LFE or Sub Out), connect an RCA cable from the receiver's subwoofer output to the SMP800's LFE input. If your receiver has stereo RCA outputs, use both L and R inputs on the SMP800.
   • 스피커 레벨 입력: If your receiver does not have a dedicated subwoofer output, connect speaker wires from your receiver's main speaker outputs to the SMP800's Speaker Level Input terminals.
2. Connect Subwoofer Output: Connect the speaker wires from the IWS88 in-wall subwoofer to the SMP800's Subwoofer Speaker Output terminals. Ensure correct polarity (+ to + and - to -).

Image: Close-up of the SMP800 amplifier's subwoofer speaker output terminals.

Image: Close-up of the SMP800 amplifier's RCA/LFE inputs and speaker level inputs.

3. 12V 트리거(옵션): If your AV receiver or control system has a 12V trigger output, connect it to the SMP800's 12V Trigger input. This allows the amp앰프를 메인 시스템과 연동하여 자동으로 켜지고 꺼지도록 설정하세요.
4. 전원 연결: Connect the supplied power cable to the SMP800 amplifier and then to a suitable AC power outlet. Ensure the AC Voltage Selector switch on the amplifier가 올바른 볼륨으로 설정되어 있습니다.tage for your region (110-120V or 220-240V).

5. 사용 설명서

5.1 전원 켜기/끄기

• 수동 전원: Press the power button on the front panel of the SMP800 amplifier to turn it on or off.
• 자동 켜짐 감지: 만약 amplifier's 'MUSIC ON 12V' switch is set to 'MUSIC' and an audio signal is detected on the RCA/LFE or Speaker Level inputs, the amplifier will automatically power on. It will enter standby mode after a period of no audio signal.
• 12V 트리거: If connected, the amplifier will power on and off in sync with your main system.

5.2 Adjusting Controls (SMP800)

The SMP800 amplifier features several controls to optimize subwoofer performance:

• 볼륨/이득: 서브우퍼의 전체 출력 레벨을 조절합니다. 낮은 설정에서 시작하여 베이스가 메인 스피커와 잘 어우러질 때까지 점차 높이십시오.
• 크로스오버 주파수: This control determines the highest frequency the subwoofer will reproduce. Set it to blend seamlessly with your main speakers. A common starting point is 80Hz-100Hz, but adjust based on your main speakers' low-frequency capabilities.
• 위상 제어 : Adjusts the phase of the subwoofer output (0° or 180°). Experiment with both settings to find the one that provides the most impactful and coherent bass response in your listening position.

6. 유지관리

To ensure the longevity and optimal performance of your OSD Audio subwoofer and amplifier의 경우 다음의 간단한 유지 관리 지침을 따르세요.

• 청소: 부드럽고 마른 천을 사용하여 표면을 청소하십시오. amplifier and subwoofer grille. Do not use liquid cleaners, aerosols, or abrasive chemicals, as they may damage the finish or internal components.
• 통풍: 정기적으로 다음 사항을 확인하십시오. amp앰프의 통풍구는 과열을 방지하기 위해 먼지와 이물질이 없도록 깨끗하게 유지됩니다.
• 사이: Occasionally check all cable connections to ensure they are secure. Loose connections can lead to signal loss or intermittent performance.
• 환경: 노출을 피하십시오 amp극한의 온도나 습도에 적응합니다.

7. 문제 해결

If you encounter issues with your OSD Audio subwoofer and amplifier bundle, refer to the following troubleshooting guide:

위 해결 방법을 시도해 보신 후에도 문제가 지속되면 OSD Audio 고객 지원팀에 문의하십시오.

8. 사양

IWS88 In-Wall Subwoofer

• 유형: Passive In-Wall Subwoofer
• 운전자: Dual 8-inch Woofers
• 파워 핸들링: 350 와트
• 임피던스: 8옴
• 주파수 응답: Refer to product page for detailed specifications.
• 치수: Refer to product page for detailed dimensions and cutout size.

SMP800 Class D Mono Amp리퍼

• Amp유형: 클래스 D 모노
• 전력 출력: 800W (최대)
• 입력: RCA/LFE, Speaker Level, 12V Trigger
• 출력: 서브우퍼 스피커 출력
• 통제 수단: Variable Crossover, Phase Control (0°/180°), Volume/Gain
• 특징: 자동 켜짐 감지
• AC 볼륨tage: Selectable (110-120V / 220-240V)
• 치수: Refer to product page for detailed dimensions.

9. 보증 및 지원

9.1 보증 정보

OSD Audio products are designed and manufactured to the highest quality standards. This product is covered by a standard manufacturer's warranty against defects in materials and workmanship. The specific terms and duration of the warranty may vary. Please retain your proof of purchase for warranty claims.

The warranty does not cover damage caused by improper installation, accident, misuse, abuse, negligence, unauthorized modification, or normal wear and tear.

9.2 고객 지원

For technical assistance, troubleshooting, or warranty inquiries, please visit the official OSD Audio website or contact their customer support department. Contact information can typically be found on the OSD Audio web사이트 또는 제품 포장에 표시되어 있습니다.

Before contacting support, please have your product model numbers (IWS88 and SMP800) and a description of the issue ready.