ALTHY UVF-FS11 UV Water Purifier Instruction Manual

1. 서론

The ALTHY UVF-FS11 UV Water Purifier is designed to enhance your existing water filtration system by providing powerful UV-C technology for safe drinking water. This manual provides essential information for the proper installation, operation, and maintenance of your UV water purifier. Please read this manual thoroughly before installation and use to ensure optimal performance and safety.

The ALTHY UV system utilizes Philips 253.7nm ultraviolet photons to penetrate and destroy the DNA and RNA of harmful substances, achieving a 99.99% purification effect.

Diagram showing how the ALTHY UV system works

Image 1.1: Diagram illustrating the ALTHY UV system's purification process. Pre-filtered water enters, passes through the UV chamber, and exits as purified water. The UV light inactivates harmful microorganisms.

2. 안전 정보

WARNING: UV-C RADIATION HAZARD

UV l을 직접 보지 마십시오.amp when it is illuminated. UV-C radiation can cause severe eye and skin damage.
Always disconnect power before performing any maintenance or service on the unit.
전기 연결부의 접지가 제대로 되었는지 확인하십시오.
Do not operate the unit if the quartz sleeve is broken or damaged.
본 제품을 어린이의 손이 닿지 않는 곳에 보관하세요.
This device is intended for use with potable water only.

이러한 안전 지침을 따르지 않을 경우 심각한 부상이나 재산 피해가 발생할 수 있습니다.

3. 제품 구성품

The ALTHY UVF-FS11 UV Water Purifier system includes the following main components:

UV Chamber (304 Stainless Steel)
Philips 11W UV-C Lamp
석영 슬리브
Silicone Seal O-ring
UVC 안정기
Smart Flow Control Switch (Flow Sensor)
마운팅 브래킷(x2)

폭발했다 view of ALTHY UV water purifier components

이미지 3.1: 상세 view of the ALTHY UV water purifier components, including the 304 stainless steel chamber, G1/4" connections, quartz sleeve, silicone O-ring, Philips 11W UVC lamp, UVC ballast, smart flow control switch, and mounting brackets.

4. 설정 및 설치

This UV purifier is designed for under-sink installation and should be added as a final stage to your existing water filtration system. It features G1/4" MNPT inlet/outlet connections.

4.1 설치 전 체크리스트

모든 구성 요소가 있고 손상되지 않았는지 확인하십시오.
Turn off the main water supply to your home or the specific cold water line where the unit will be installed.
근처 수도꼭지를 열어 수압을 낮추세요.
Have necessary tools ready (e.g., wrench, Teflon tape, drill for mounting).

4.2 설치 단계

Mount the UV Chamber: Use the provided mounting clips to securely attach the UV chamber to a sturdy surface under your sink. Ensure there is enough space for future lamp 대사.
급수관 연결:
- Connect the outlet of your existing water purifier to the inlet (G1/4") of the ALTHY UVF-FS11 system.
- Connect the outlet (G1/4") of the ALTHY UVF-FS11 system to your drinking water faucet.
- Use appropriate fittings and Teflon tape to ensure leak-free connections.
UV L 설치amp and Quartz Sleeve:
- Carefully insert the quartz sleeve into the UV chamber.
- Place the silicone O-ring correctly to ensure a watertight seal.
- Gently insert the Philips 11W UV-C lamp into the quartz sleeve. Avoid touching the lamp with bare hands; use gloves or a clean cloth.
- l을 보안하세요amp and sleeve assembly with the retaining nut/cap.
전기 부품 연결:
- UV l을 연결하십시오amp to the UVC Ballast.
- Connect the Smart Flow Control Switch (flow sensor) to the UVC Ballast.
- Plug the UVC Ballast into a grounded 110V-240V electrical outlet.
누출 확인: Slowly turn on the main water supply. Inspect all connections for leaks. Tighten any leaking connections as needed.
초기 플러시: After installation, open your drinking water faucet and allow water to flow through the system for 2-3 minutes to flush out any air or carbon fines.

Under-sink installation diagram for ALTHY UVF-FS11

Image 4.1: Under-sink installation diagram showing the connection of the UVF-FS11 purifier system after a water purifier and before the drinking water faucet, including the flow sensor.

5. 사용 설명서

The ALTHY UVF-FS11 features an intelligent smart flow sensor for automatic operation and energy efficiency.

5.1 자동 작동

When water flows through the UV chamber, the smart flow sensor detects the flow, and the UV lamp 자동으로 켜집니다.
The ballast display panel will show a countdown timer.
When water flow stops, the UV lamp will remain on for an additional 600 seconds (10 minutes). This ensures that any residual water in the chamber receives full UV treatment.
After the 600-second countdown completes, the UV lamp will automatically turn off to save energy and prolong lamp 삶.
난amp will immediately turn back on when water flow is detected again.

ALTHY UV purifier with smart flow sensor and UV lamp

Image 5.1: The ALTHY UV purifier showing the preinstalled smart flow sensor that automatically controls the UV light, and the durable Philips UV lamp.

6. 유지관리

Regular maintenance is crucial for the continued effectiveness and longevity of your ALTHY UVF-FS11 system.

6.1 UVLamp 대사

The Philips 11W UV-C lamp has an estimated lifespan of up to 8,000 hours.
UV l을 교체하는 것이 좋습니다.amp annually to ensure optimal purification performance, even if it appears to be working. The ballast display may indicate when replacement is due.
대체 절차 :
1. 장치의 전원을 분리합니다.
2. 물 공급을 차단하고 압력을 낮추세요.
3. Carefully remove the retaining nut/cap and pull out the old UV lamp.
4. Gently slide out the quartz sleeve and clean it thoroughly (see 6.2).
5. Insert the new Philips 11W UV-C lamp into the clean quartz sleeve.
6. Reassemble the unit in reverse order of installation.
7. Turn on water and power, then check for leaks.

6.2 Quartz Sleeve Cleaning

The quartz sleeve should be cleaned regularly, at least annually during lamp replacement, or more frequently if water quality is poor.
Mineral deposits or sediment on the quartz sleeve can reduce the effectiveness of the UV light.
청소 절차:
1. Disconnect power and water supply.
2. UV l 제거amp and then carefully slide out the quartz sleeve.
3. Clean the quartz sleeve with a soft cloth and a mild descaling solution (e.g., vinegar or citric acid) to remove any mineral buildup. Rinse thoroughly with clean water.
4. Inspect the quartz sleeve for cracks or damage. Replace if damaged.
5. Reinstall the clean quartz sleeve and UV lamp.

Image 6.1: Chart illustrating the effectiveness of Philips UV-C lamps at 253.7nm wavelength for germicidal reduction compared to other brands.

7. 문제 해결

This section provides solutions to common issues you might encounter with your ALTHY UVF-FS11 system.

문제	가능한 원인	해결책
자외선amp 켜지지 않음	No power to the ballast. Faulty UV lamp. 밸러스트에 결함이 있습니다. Flow sensor not detecting water.	전원 연결과 콘센트를 확인하세요. UV l 교체amp (유지보수 섹션을 참조하십시오.) Contact customer support if ballast is suspected faulty. Ensure water is flowing through the unit. Check flow sensor connections.
물 누출	느슨한 연결. Damaged O-ring or quartz sleeve. 부품이 제대로 장착되지 않았습니다.	Tighten all water line connections. Inspect and replace O-rings or quartz sleeve if damaged. Ensure UV lamp and quartz sleeve are correctly installed and sealed.
물의 흐름이 감소함	Clogged pre-filter (if applicable). Sediment buildup in UV chamber or quartz sleeve.	Check and replace pre-filters in your main filtration system. Clean the quartz sleeve (refer to Maintenance section).

8. 사양

특징	세부 사항
모델 번호	UVF-FS11
제조업체	ALTHY
치수(길이 x 너비 x 높이)	24.99 x 4.5 x 4.5cm (약 9.84 x 1.77 x 1.77인치)
무게	1.1kg(약 2.4파운드)
재료	304 스테인리스 스틸
전원	Electric Cord (110V-240V, 11W Ballast)
설치 방법	언더 싱크
유량	1 Gallon per Minute (GPM)
특별 기능	Automatic Shut-off, Smart Flow Sensor
UV 엘amp 유형	Philips UV-C 11W
UV 엘amp 수명	최대 8,000시간
정화 방법	UV(자외선)
입구/출구 연결	G1/4" MNPT

9. 보증 및 지원

9.1 보증 정보

For detailed warranty information regarding your ALTHY UVF-FS11 UV Water Purifier, please refer to the product packaging or visit the official ALTHY web사이트. 보증 약관은 지역 및 구매일자에 따라 다를 수 있습니다.

9.2 고객 지원

If you have any questions, require technical assistance, or need to report an issue, please contact ALTHY customer service. You can typically find contact information on the product packaging or the manufacturer's official web대지.

"Si vous avez des questions, vous pouvez nous contacter via le service client en ligne" - As stated in the product description, online customer service is available for inquiries.

ALTHY UVF-FS11