NEEBRC AM32 ESC USB Linker Program Instruction Manual

1. 서론

The NEEBRC AM32 ESC USB Linker Program is a compact device designed to facilitate the configuration and firmware updates for AM32/BL32 brushless Electronic Speed Controllers (ESCs). This linker connects your ESC to a computer, allowing you to adjust parameters and manage firmware using compatible software.

2. 안전 정보

Please read this instruction manual carefully before use to ensure proper operation and prevent damage to the device or connected components. Always handle electronic components with care. Avoid exposing the linker to moisture, extreme temperatures, or static electricity. Disconnect power from the ESC before making any physical connections or disconnections.

3. 패키지 내용

• 1 x AM32 ESC Param Converter (USB Link)

4. 제품 오버view

The AM32 ESC USB Linker is a compact and portable tool for managing your AM32/BL32 ESCs. It features a standard USB-A connector for computer interface and a 3-pin header for connecting to the ESC's signal port.

주요 특징:

• Connects AM32/BL32 ESCs to a computer for configuration or firmware upgrades.
• Portable and user-friendly design.
• Requires connection of the ESC signal plug and a USB cable to a computer.
• Compatible with AM32 firmware, designed for AT32 ARM processors for brushless motor control (BLDC).
• Supports safe, fast, smooth, and linear throttle response for various RC vehicle types and flight controllers.

이미지 1: 상단 view of the AM32 ESC USB Linker, highlighting the USB-A connector and the 3-pin header for ESC connection.

이미지 2: 하단 view of the AM32 ESC USB Linker, revealing the main chip and surface-mounted components.

이미지 3: 각도 view of the AM32 ESC USB Linker, providing a clear perspective of both connection points.

5. 설정 지침

1. Connect the ESC: Connect the 3-pin signal cable from your AM32/BL32 ESC to the 3-pin header on the USB Linker. Ensure the polarity is correct (Signal, 5V, Ground).
2. Power Wire Consideration: If your ESC is already powered by another source (e.g., a flight controller or battery eliminator circuit), it is recommended to cut the red 5V power wire from the servo extension cable connecting the ESC to the linker. This prevents redundant power supply to the linker and your computer, which could cause damage. Only the signal and ground wires are typically required for programming.
3. 컴퓨터에 연결: Plug the USB-A connector of the linker into an available USB port on your computer.
4. VCP 드라이버 설치: Your computer may require a Virtual COM Port (VCP) driver to recognize the linker. Download and install the appropriate VCP driver for your operating system from the chip manufacturer's website (e.g., Silicon Labs CP210x or FTDI).
5. 소프트웨어 다운로드: Obtain the latest AM32/BL32 configuration software. This software is usually available from the official AM32 project website or your specific ESC manufacturer's support page.

6. 사용 설명서

1. 소프트웨어 실행: Open the AM32/BL32 configuration software on your computer.
2. COM 포트를 선택하십시오. In the software settings, identify and select the correct COM port that corresponds to the USB Linker. This port number can typically be found in your computer's Device Manager (Windows) or System Information (macOS/Linux) under 'Ports (COM & LPT)'.
3. Connect to ESC: Click the 'Connect' or 'Read Settings' button within the software to establish communication with the ESC.
4. Configure/Update: Once connected, you can now adjust various parameters of your ESC, update its firmware, or perform other supported configurations as provided by the AM32/BL32 software.
5. 변경 사항 적용: After making any changes, ensure you click 'Write Settings' or 'Flash Firmware' to save them to the ESC. Do not disconnect the linker or power during this process.
6. 연결 해제: After successful configuration, disconnect the ESC from the linker and the linker from your computer.

7. 유지관리

• Keep the USB Linker clean and dry.
• Avoid exposing the device to dust, dirt, moisture, or corrosive substances.
• Store the linker in a safe place away from direct sunlight and extreme temperatures when not in use.
• Do not attempt to disassemble or modify the device, as this will void any warranty and may cause damage.

8. 문제 해결

• Linker not recognized by computer:
  • Ensure the VCP drivers are correctly installed for your operating system.
  • Try connecting the linker to a different USB port on your computer.
  • 컴퓨터를 재시작하고 다시 시도하세요.
  • Verify the USB cable (if detachable) is functional.
• Software cannot connect to ESC:
  • Confirm that the correct COM port is selected in the configuration software.
  • Check all physical connections between the linker, ESC, and computer.
  • Ensure the ESC is powered on (if required by the software for communication, but observe power wire precautions).
  • COM 포트를 사용 중인 다른 애플리케이션이 있으면 모두 닫으세요.
• Programming or firmware update errors:
  • Ensure you are using the correct firmware version for your specific ESC model.
  • Do not interrupt the programming process by disconnecting power or the linker.
  • Verify the ESC has sufficient power during the update.

9. 사양

10. 보증 및 지원

For specific warranty information and technical support, please refer to the product's purchase page on Amazon or contact NEEBRC directly through their official channels. Keep your proof of purchase for any warranty claims.