소개
The JHS Pedals COLOUR BOX 10 is a studio-quality preamp, EQ, and distortion unit designed for compatibility with various instruments. This manual provides detailed instructions for its setup, operation, and maintenance.
패키지 내용
설치를 진행하기 전에 모든 항목이 있는지 확인하세요.
- COLOUR BOX 10 Pedal
- 입력 선택 스위치
- 전원 케이블
주요 특징
- Incorporates an Output Transformer for enhanced signal integrity.
- Safely Handles 48V Phantom Power, suitable for condenser microphones.
- Precision EQ Control with dedicated EQ Shift Knobs for detailed tone shaping.
- Ultra Clean Headroom with Hi/Lo Switch for versatile gain stag주고받음.
- Consistent Clean Signal on Acoustic Guitar, preserving natural tone.
- Silent Operation, No Switch-Pop, ensuring smooth performance transitions.
- Powered by Standard 9V DC Negative Power for easy integration into existing setups.
제어 및 연결
The COLOUR BOX 10 features a comprehensive set of controls for precise sound sculpting. Refer to the image below for a visual guide to the pedal's layout.
그림 1: 상단 view of the JHS Pedals COLOUR BOX 10, showing all control knobs and switches.
컨트롤 노브:
- 주인: 페달의 전체 출력 볼륨을 조절합니다.
- Pre-Vol: Adjusts the input gain, influencing the amount of saturation and distortion.
- 단계: A stepped gain control that adds distinct stages of gain and color to the signal.
- Hi Pass: Controls the cutoff frequency for the high-pass filter. Turning clockwise increases the cutoff frequency, removing more low-end.
- 고음부: Adjusts the high-frequency equalization.
- 가운데: Adjusts the mid-frequency equalization.
- 베이스: Adjusts the low-frequency equalization.
- 고음 이동: Shifts the center frequency of the Treble EQ band.
- Mid Shift: Shifts the center frequency of the Middle EQ band.
- Bass Shift: Shifts the center frequency of the Bass EQ band.
스위치:
- Hi Pass Toggle Switch: Activates or deactivates the Hi Pass filter.
- Hi/Lo Toggle Switch: Selects between high and low headroom modes, affecting the overall gain structure and clean signal.
사이:
- Input (1/4" TRS): Connect your instrument or microphone.
- Output (XLR): Connect to an audio interface, mixer, or amp리퍼.
- 9V DC 전원 입력: Connect a standard 9V DC negative center power supply.
설치 가이드
- 전원 연결: Connect the provided 9V DC power cable to the pedal's power input. Ensure you use a standard 9V DC negative center power supply.
- Instrument/Microphone Input: Connect your instrument (e.g., guitar, bass) or microphone to the 1/4" TRS input jack. If using a microphone requiring phantom power, the COLOUR BOX 10 can safely handle 48V phantom power.
- 출력 연결: Connect the XLR output of the COLOUR BOX 10 to your audio interface, mixing console, or amp리퍼.
- 초기 설정: Before powering on, set all control knobs to their middle position (12 o'clock) and ensure both toggle switches are in their neutral or 'off' position (if applicable, for Hi Pass).
- 전원 켜기: Apply power to the pedal. The indicator LED should illuminate.
작동 지침
The COLOUR BOX 10 offers extensive tonal possibilities. Experiment with the controls to find your desired sound.
이득 Staging:
- 사용하세요 Pre-Vol knob to adjust the initial gain. Higher settings will introduce more saturation and distortion.
- 그만큼 단계 knob provides incremental gain stages, adding character and drive.
- 그만큼 하이/로우 toggle switch selects between two headroom settings. 'Hi' offers more clean headroom, while 'Lo' provides earlier breakup and compression.
평준화:
- 조정하다 고음부, 가운데, 그리고 베이스 음색을 조절할 수 있는 노브.
- 활용하다 Treble Shift, Mid Shift, 그리고 Bass Shift knobs to fine-tune the frequency centers of each EQ band, allowing for precise tonal adjustments.
- 그만큼 하이패스 filter, activated by its toggle switch, can be used to remove unwanted low-end rumble or to tighten up your sound. Adjust the 하이패스 knob to set the cutoff frequency.
출력 레벨 :
그만큼 주인 knob controls the final output volume. Adjust this to match the input level of your next device in the signal chain.
유지
- 청소: 페달 외부를 닦을 때는 부드럽고 마른 천을 사용하세요. 연마성 세제나 용제는 사용하지 마세요.
- 저장: 페달은 극한의 온도와 습도를 피해 건조한 환경에 보관하세요.
- 전원 공급 장치: Always use the correct 9V DC negative center power supply to prevent damage.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 소리가 출력되지 않습니다. | Incorrect power supply, loose cables, pedal bypassed. | Verify power connection and supply specifications. Check all input/output cables. Ensure the pedal is engaged. |
| 과도한 소음이나 윙윙거림. | Ground loop, faulty cables, proximity to interference sources. | Use isolated power supply. Try different cables. Move pedal away from power transformers or digital devices. |
| Distortion is too high/low. | Pre-Vol or Step knob settings, Hi/Lo switch position. | Adjust Pre-Vol and Step knobs. Experiment with the Hi/Lo switch to find desired gain structure. |
명세서
| 특징 | 세부 사항 |
|---|---|
| 품목 무게 | 1.57파운드 |
| 제품 치수 | 6.75 x 4.35 x 3.4 인치 |
| 전원 | 직류 전원 |
| 권tage | 9 볼트 |
| 커넥터 유형 | XLR, 1/4" TRS |
| 재료 유형 | Metal, Circuit Board |
| 첫 번째 가능한 날짜 | 7년 2024월 XNUMX일 |
보증 및 지원
For warranty information and technical support, please refer to the official JHS Pedals web사이트를 방문하거나 고객 서비스에 직접 문의하세요. 보증 청구를 위해 구매 영수증을 보관하세요.
JHS Pedals Official Web대지: www.jhspedals.com