Pro-Ject Debut EVO 2 Turntable Instruction Manual

1. 서론

Thank you for choosing the Pro-Ject Debut EVO 2 Turntable. This high-fidelity record player is crafted in Europe by hand, offering an enhanced listening experience. It features a heavy platter, a carbon fiber tonearm with a resonance-damping aluminum bearing block, and an adaptive anti-skating system. The turntable comes pre-mounted with a Pick it MM EVO Moving Magnet Phono Cartridge and includes a DC/AC power generator. This manual provides essential information for setting up, operating, and maintaining your turntable to ensure optimal performance and longevity.

2. 패키지 내용

다음 품목이 모두 패키지에 포함되어 있는지 확인하세요.

• Pro-Ject Debut EVO 2 Turntable Unit
• Pick it MM EVO Moving Magnet Phono Cartridge (pre-mounted)
• 15V DC 0.8A Power Supply
• 더스트 커버
• 7'' Singles Adapter
• 안전 벨트
• 균형추
• 안티 스케이팅 무게

3. 설정 지침

Follow these steps carefully to set up your Pro-Ject Debut EVO 2 Turntable.

3.1 포장 풀기 및 배치

포장에서 모든 구성품을 조심스럽게 꺼내십시오. 턴테이블을 직사광선, 열원 및 진동을 피해 안정적이고 평평한 곳에 놓으십시오.

3.2 Platter and Drive Belt Installation

1. Place the main platter onto the central spindle.
2. Carefully loop the drive belt around the motor pulley and the inner rim of the platter. Ensure the belt is not twisted.

3.3 톤암 및 카트리지 설치

1. Slide the counterweight onto the rear of the tonearm with the numbers facing forward.
2. The Pick it MM EVO cartridge is pre-mounted on the headshell. Attach the headshell to the tonearm and tighten the locking nut securely.
3. Carefully remove the stylus protector from the cartridge.
4. Unlock the tonearm from its rest. Lift the cueing lever.
5. While holding the headshell, lower the cueing lever completely. Do not let the stylus touch the platter.
6. Turn the counterweight until the tonearm floats parallel to the platter. This is the balanced position.
7. Once balanced, return the tonearm to its rest and lock it.
8. Turn only the numbered ring of the counterweight to '0' on the center line. Do not turn the entire counterweight.
9. Now, turn the entire counterweight (including the numbered ring) counter-clockwise until the desired tracking force is set (e.g., 2 grams for the Pick it MM EVO cartridge).
10. Locate the anti-skating dial near the tonearm base. Set this dial to the same value as your tracking force (e.g., '2').

3.4 Dust Cover and Connections

1. Attach the dust cover hinges to the turntable chassis and then carefully place the dust cover onto the hinges.
2. Connect the turntable's RCA output cables to your amplifier's phono input (or a separate phono preamp리퍼).
3. Connect the ground wire from the turntable to your amp앰프의 접지 단자.
4. Plug the 15V DC 0.8A power supply into the turntable and then into a wall outlet.

3.5 설정 비디오

For a visual guide on the initial setup, please watch the following video:

4. 사용 설명서

4.1 레코드 재생하기

1. 플래터에 레코드를 놓습니다.
2. Select the correct playback speed (33 or 45 RPM) using the speed selector switch.
3. Unlock the tonearm and lift it using the cueing lever.
4. Carefully position the stylus over the desired groove on the record.
5. 큐잉 레버를 천천히 내려 스타일러스가 레코드판 위로 내려가도록 하십시오.

4.2 재생 중지

1. 큐잉 레버를 사용하여 톤암을 들어 올리십시오.
2. Return the tonearm to its rest and lock it in place.
3. 턴테이블에서 레코드를 꺼내세요.
4. Turn off the turntable using the power switch.

5. 유지관리

5.1 스타일러스 청소

Use a soft stylus brush to gently clean the stylus from back to front. Never brush from front to back, as this can damage the stylus.

5.2 턴테이블 청소

Wipe the dust cover and plinth with a soft, dry, anti-static cloth. Avoid using abrasive cleaners or solvents.

5.3 Drive Belt Inspection

Periodically inspect the drive belt for any signs of wear or stretching. A worn belt can affect playback speed and consistency.

6. 문제 해결

If you encounter any issues with your turntable, please refer to the following common solutions:

• 소리 없음: Check all cable connections (RCA, ground, power). Ensure your amplifier is set to the correct input and volume.
• 왜곡된 소리: Verify that the tracking force and anti-skating settings are correct. Ensure the stylus is clean and undamaged.
• 잘못된 속도: Confirm the drive belt is properly seated and not worn. Ensure the correct speed (33/45 RPM) is selected.
• 허밍 소음: Check the ground wire connection. Ensure the turntable is placed away from electronic devices that may cause interference.

If problems persist, please contact Pro-Ject customer support.

7. 사양

8. 보증 및 지원

For warranty information and technical support, please refer to the documentation included with your product or visit the official Pro-Ject Audio Systems web사이트. 보증 청구를 위해 구매 증빙 자료를 보관하세요.