소개
The Geeni Smart Water Alarm Leak Detector with Siren is designed to provide early warning of water leaks in your home. This device helps prevent potential water damage by detecting leaks and alerting you through its built-in siren and mobile application. It integrates with your home Wi-Fi network for remote monitoring and smart home automation.
주요 특징
- Instant Leak Detection: Rapidly identifies the presence of water.
- 실시간 알림: Sends immediate notifications to your smartphone.
- Built-in 80dB Alarm: Emits a loud siren to alert occupants.
- Monitor from Anywhere: Access device status and alerts remotely via the Geeni app.
- 스마트 홈 통합: Compatible with other Geeni smart home products for automated responses.
- 배터리 부족 경고: 배터리 교체 시기가 되면 알려줍니다.
- 간편한 설정: 빠르고 간편한 설치를 위해 설계되었습니다.
- 24/7 Peace of Mind: Continuous monitoring for enhanced home safety.
Figure 1: Key features of the Geeni Smart Water Alarm Leak Detector.
패키지 내용
패키지에 모든 품목이 들어 있는지 확인하세요.
- 1x Geeni Smart Water Sensor
- 1x Siren Mounting Adhesive
- 1x 사용자 설명서
- AAA 배터리 2개
그림 2: 제품 패키지에 포함된 내용.
제품 끝view
Familiarize yourself with the components of your Geeni Smart Water Alarm Leak Detector:
- LED 조명: Indicates device status (e.g., pairing mode, leak detected).
- 키 설정: 기기를 페어링하고 재설정하는 데 사용됩니다.
- 스피커: Emits the 80dB siren alarm.
- 센서 프로브: The part that detects water. Must be placed flat on the surface where leaks may occur.
- 배터리 칸: Holds 2x AAA batteries.
- 케이블 길이: The sensor probe is connected to the main unit by a 3.28 ft (1 m) cable.
그림 3: 앞면과 뒷면 view of the device with labeled components and dimensions.
설정
1. 배터리 설치
- 본체 뒷면의 배터리함을 여세요.
- AAA 배터리 2개를 극성을 확인하여 삽입하십시오.
- 배터리 칸을 단단히 닫으세요.
2. Download and Install the Geeni App
- 검색 애플 앱스토어 또는 구글 플레이 스토어에서 "Geeni"를 검색하세요.
- 앱을 다운로드하고 설치하세요.
- 새 계정을 등록하거나 이미 계정이 있는 경우 로그인하세요.
3. Pair the Device with Wi-Fi
- Ensure your smartphone is connected to a 2.4 GHz Wi-Fi network. The device does not support 5 GHz networks.
- Geeni 앱을 열고 "+" 아이콘을 탭하여 새 기기를 추가하세요.
- Follow the on-screen instructions in the app to put the water sensor into pairing mode and connect it to your Wi-Fi network. The LED light on the device will indicate its pairing status.
4. 장치 배치
Strategically place the water sensor in areas prone to leaks:
- 싱크대 아래 (주방, 욕실)
- In basements
- 온수기 근처
- In laundry rooms
- Behind dishwashers or refrigerators
Use the provided mounting adhesive to secure the main unit. Ensure the sensor probe lies flat on the surface where water might accumulate first.
그림 4: 예amples of multi-use placement for the water sensor.
작업
Leak Detection and Alerts
Once installed and connected, the Geeni Smart Water Alarm continuously monitors for water. When the sensor probe detects water:
- The device will emit a loud 80-decibel siren.
- You will receive an immediate notification on your smartphone via the Geeni app.
Figure 5: Real-time leak detection and app notification.
알람 설정 조정
You can customize the alarm settings through the Geeni app:
- 사이렌 볼륨: Adjust the volume from mute (0dB) up to 80dB.
- 알람 지속 시간: Set the duration of the siren from 30 seconds to 180 seconds.
Figure 6: Alarm volume and duration adjustment options.
유지
배터리 교체
The device is powered by 2x AAA batteries with an expected lifespan of 3-4 months. The Geeni app will send a low battery alert when replacement is needed.
- When a low battery alert is received, open the battery compartment.
- Remove the old batteries and insert two new AAA batteries, observing correct polarity.
- 배터리 칸을 닫습니다.
장치 테스트
It is recommended to periodically test the water sensor to ensure it is functioning correctly:
- Place a small amount of water (e.g., a few drops) onto the sensor probe.
- Verify that the siren sounds and you receive a notification on your smartphone.
- Dry the sensor probe thoroughly after testing.
문제 해결
- 장치가 Wi-Fi에 연결되지 않음:
Ensure your Wi-Fi network is 2.4 GHz. The device does not support 5 GHz. Try moving the device closer to your Wi-Fi router. If issues persist, try deleting the device from the Geeni app and re-pairing it following the setup instructions. - 앱 알림 없음:
Check your smartphone's notification settings for the Geeni app to ensure notifications are enabled. Also, verify that the device is properly connected to Wi-Fi and has sufficient battery power. - Siren not sounding or too quiet:
Check the battery level. Ensure the siren volume is not set to mute in the Geeni app settings. - Sensor not detecting water:
Ensure the sensor probe is lying flat and making good contact with the surface where water might collect. Clean the sensor contacts if they appear dirty. - Device appears offline in app:
Check your Wi-Fi connection. If the Wi-Fi network is down or unstable, the device may appear offline. Replace batteries if they are low.
For further assistance, refer to the support section within the Geeni app or visit support.mygeini.com.
명세서
| 상표 | 지니 |
| 모델 | B0D47W56TY |
| 전원 | 배터리 구동(AAA 2개) |
| 배터리 수명 | Approximately 3-4 months |
| 호환 장치 | Android, iOS (Smartphone, Tablet) |
| 제품 치수(본체) | 3.54인치(길이) x 1.97인치(너비) x 5.12인치(높이) (90mm(길이) x 50mm(너비) x 130mm(높이)) |
| 제어 방법 | Geeni App |
| 가청 소음 | 80데시벨 |
| 장착 유형 | Adhesive (for main unit), Sensor probe placed on surface |
| 센서 기술 | 접촉 센서 |
| Cable Length (Sensor) | 3.28피트(1m) |
| Wi-Fi 연결 | 2.4GHz 전용 |
| IP 등급 | IP44 |
보증 및 지원
보증 정보
이 Geeni 제품에는 다음이 포함됩니다. 1년 한정 보증 구매일로부터 1년입니다. 보증 청구를 위해 구매 증빙 자료를 보관해 주십시오. 보증은 정상적인 사용 상태에서 발생하는 재료 및 제조상의 결함에 적용됩니다.
고객 지원
If you encounter any issues or have questions regarding your Geeni Smart Water Alarm Leak Detector, please contact Geeni customer support:
- 온라인 지원: 방문하다 support.mygeini.com
- 앱 내 지원: Access support directly through the Geeni mobile application.