FLARING 플라즈마 절단기 사용 설명서

1. 서론

The FLARING FC650DL 5th Generation Plasma Cutter is a powerful and portable tool designed for efficient metal cutting. Featuring non-touch pilot arc technology, it allows for cutting without direct contact between the tip and the metal, enhancing cutting quality and extending consumable lifespan. This machine supports dual voltage operation (120V/240V) and is suitable for a wide range of materials including stainless steel, alloy steel, mild steel, copper, and aluminum.

This manual provides essential information for the safe and effective operation, setup, and maintenance of your FLARING plasma cutter. Please read it thoroughly before use.

2. 안전 정보

WARNING: Always wear appropriate personal protective equipment (PPE) including welding helmet with proper shade, flame-resistant clothing, welding gloves, and safety shoes when operating the plasma cutter. Ensure adequate ventilation to avoid inhaling fumes.

• 전기 안전: Ensure the machine is properly grounded. Do not operate in wet conditions. Disconnect power before performing any maintenance or assembly.
• 화재 위험: Plasma cutting produces sparks and molten metal. Keep flammable materials away from the work area. Have a fire extinguisher readily available.
• 연기 및 가스: Work in a well-ventilated area or use local exhaust ventilation to remove fumes. Avoid breathing fumes directly.
• 눈과 피부 보호: Protect eyes from arc rays and sparks with a welding helmet. Protect skin from burns with appropriate clothing.
• 핫 부품: The torch and workpiece will be hot after cutting. Allow them to cool before handling.

3. 패키지 내용

아래 나열된 모든 품목이 패키지에 포함되어 있는지 확인하세요.

• 플레어링 65 amps plasma cutter machine FC650DL 5GEN
• Upgrade plasma cutting torch AG60
• Heavy-duty work ground clamp
• Air filter regulator
• 공기 호스
• Consumables (5 electrodes, 5 tips)
• Conversion cord (110V to 220V or 120V to 240V)
• 사용 설명서

Figure 3.1: Included accessories and components with the FLARING FC650DL plasma cutter.

4. 설정

4.1 에어 필터 어셈블리

Attach the air filter regulator to the back of the plasma cutter. Ensure the connections are secure to prevent air leaks. The air filter helps to remove moisture and contaminants from the compressed air supply, which is crucial for optimal cutting performance and longevity of consumables.

Figure 4.1: The air filter regulator, an essential component for clean air supply.

4.2 Torch Assembly

Assemble the AG60 torch by inserting the electrode and tip into the torch head. Ensure they are seated correctly and tighten the retaining cap. Proper assembly of the torch is vital for stable arc initiation and consistent cutting.

Figure 4.2: The plasma cutter with its assembled torch, ready for connection.

4.3 Connecting Leads

접지선을 연결하세요amp to the appropriate terminal on the plasma cutter and securely attach it to the workpiece. Connect the torch cable to its designated connector on the machine. Ensure all connections are tight to maintain proper electrical conductivity and safety.

4.4 전원 연결

The FLARING FC650DL supports dual voltage (120V/240V). Use the included conversion cord to adapt to your power supply. For 240V, a 30A circuit breaker is recommended. For 120V, a 60A circuit breaker is recommended. Always ensure the power source matches the machine's requirements and is properly rated for the current draw.

5. 사용 설명서

5.1 일반 작업

Once the machine is set up and connected, turn on the power switch. Adjust the current knob to the desired amperage based on the material thickness. The pilot arc technology allows for cutting without direct contact, making it easier to start cuts on painted or rusty surfaces. Maintain a consistent travel speed for clean and efficient cuts.

5.2 Cutting Thickness

The FC650DL offers excellent cutting capabilities. Under 220/240V, it achieves an ideal clean cut of 1/2 inch (12.7mm) and a maximum severance cut of 4/5 inch (20mm). For 110/120V, the ideal clean cut is 2/5 inch and maximum severance cut is 3/5 inch.

Figure 5.1: Cutting thickness capabilities of the FLARING FC650DL.

Figure 5.2: FC650DL cutting thickness details for 210-250V and 110-125V.

5.3 재료 호환성

The FLARING FC650DL is designed for cutting a variety of conductive metals. It is suitable for cutting Stainless Steel, Alloy Steel, Mild Steel, Copper, and Aluminum. Always ensure the material is clean and free of excessive rust or paint for best results.

Figure 5.3: A variety of cutting to meet all your needs.

6. 유지관리

정기적인 유지관리는 플라즈마 커터의 수명과 최적의 성능을 보장합니다.

• 에어 필터: Regularly check and drain the moisture from the air filter bowl. Replace the filter element if it becomes excessively dirty or clogged.
• 소모품: Inspect the torch electrode and tip before each use. Replace them when they show signs of wear (e.g., pitting, erosion) to maintain cutting quality.
• 청소: Keep the machine clean and free of dust and metal particles. Use compressed air to blow out internal components periodically, ensuring the machine is unplugged.
• 케이블 및 연결: Check all cables and connections for damage, fraying, or loose fittings. Repair or replace as necessary.
• 저장: 플라즈마 절단기를 사용하지 않을 때는 건조하고 깨끗한 곳에 보관하십시오.

7. 문제 해결

This section addresses common issues you might encounter with your plasma cutter.

8. 사양

9. 보증 및 지원

FLARING products are designed for durability and performance. For warranty information, technical support, or service inquiries, please refer to the contact details provided on the product packaging or visit the official FLARING web사이트. 보증 청구에 대비해 구매 증빙 자료로 구매 영수증을 보관하세요.