1. 서론
The Ortis Hi-Lo Sump Pump Switch Controller KJ-033 is an electronic adjustable float switch designed for automatic water level management in various applications such as sewage pits, fish tanks, and water tanks. It features stainless steel anti-corrosion dual sensors and supports both 220V and 110V AC power inputs. This manual provides detailed instructions for installation, operation, maintenance, and troubleshooting to ensure optimal performance and longevity of your device.
2. 안전 정보
설치 및 작동 전에 모든 안전 지침을 주의 깊게 읽으십시오. 지침을 따르지 않으면 감전, 화재 또는 심각한 부상이 발생할 수 있습니다.
- 전기적 위험: 설치, 유지보수 또는 문제 해결 작업을 수행하기 전에 반드시 전원 공급 장치를 차단하십시오.
- 권tage 호환성: 전원 공급 장치의 볼륨을 확인하십시오.tage matches the controller's specifications (220V/110V AC).
- 적절한 접지: 기기를 항상 접지된 콘센트에 연결하십시오.
- 물 노출: Do not immerse the controller unit in water. The controller unit is designed to be mounted above the water level.
- 적격 직원: Installation and electrical connections should be performed by qualified personnel if you are unsure.
- 환경 조건: Do not operate the device in explosive atmospheres or where flammable liquids or gases are present.
3. 제품 특징
The Ortis KJ-033 controller offers several features for reliable water level management:
- Dual Stainless Steel Sensors: Anti-corrosion sensors for accurate water level detection.
- Adjustable Sensor Range: Sensors can be adjusted from 1/2 inch to 20 inches to define high and low water levels.
- 다양한 작동 모드: Supports Drain Mode (for emptying) and Water Mode (for filling).
- LED 표시등: Visual feedback for power, load status, and alarm conditions.
- 과부하 보호: Integrated protection for connected pumps.
- 음소거 기능: Allows silencing of the alarm.
- 다양한 용도: Suitable for sewage pits, fish tanks, water tanks, and other water management systems.
그림 3.1: Ortis Water Level Controller Overview 주요 특징 포함.
그림 3.2: Various Application Scenarios for the Controller.
4. 설정 및 설치
Proper installation is crucial for the reliable operation of the controller.
4.1 컨트롤러 장착
The controller unit should be mounted in a dry location, above the maximum water level, and within reach of a grounded power outlet.
- 나사 장착: Use appropriate screws and anchors to secure the controller to a wall or stable surface through the mounting tabs.
- 흡입 컵 장착: For temporary or non-permanent installations, a suction cup can be used to attach the controller to a smooth, clean surface.
그림 4.1: Controller Installation Methods.
4.2 Sensor Installation and Adjustment
The dual sensors detect the high and low water levels. Their position determines the operating range of your pump.
- 센서 배치: Position the sensors vertically in the water, ensuring they are securely fastened and will not move. The lower sensor defines the 'low' water level, and the upper sensor defines the 'high' water level.
- 조정 가능한 범위: The sensors can be adjusted along their cables to set the desired water level range, from 1/2 inch to 20 inches apart. Ensure both sensors are submerged at the desired 'on' level and the lower sensor is exposed at the desired 'off' level for drain mode, or vice versa for water mode.
- 케이블 관리 : Route sensor cables to prevent entanglement or damage.
그림 4.2: Adjustable Sensor Installation.
4.3 전기 연결
- 전원 플러그: Plug the controller's power cord into a grounded 220V or 110V AC outlet.
- 펌프 연결: Plug your sump pump or other load device into the outlet on the front of the controller. Ensure the pump's power requirements do not exceed the controller's output capacity (15A, up to 2HP).
그림 4.3: Example Sump Pit Installation.
5. 사용 설명서
The controller features a simple interface for selecting operating modes and managing alarms.
그림 5.1: 제어판 이상view.
5.1 모드 선택
Use the 'Drain' and 'Water' buttons to select the desired operating mode:
- 배수 모드: (LED indicator 'Drain' illuminates) In this mode, the controller activates the pump when the water level reaches the upper (high) sensor and deactivates it when the water level drops below the lower (low) sensor. This mode is typically used for emptying sewage pits or sumps.
- 물 모드: (LED indicator 'Water' illuminates) In this mode, the controller activates the pump when the water level drops below the lower (low) sensor and deactivates it when the water level reaches the upper (high) sensor. This mode is typically used for replenishing water in fish tanks or water tanks.
5.2 Power and Operation Switch
The main switch controls the power and operational state of the connected load:
- 자동 : (LED indicator 'AUTO' illuminates) The controller operates automatically based on the selected mode (Drain or Water) and sensor readings.
- OFF : (LED indicator 'OFF' illuminates) The connected pump is turned off, regardless of water levels.
- 에: (LED indicator 'ON' illuminates) The connected pump is continuously turned on, regardless of water levels. Use this for manual override or continuous operation.
5.3 음소거 기능
Press the 'Mute' button to silence any active alarms. The 'DisAlarm' LED will illuminate when the alarm is muted.
그림 5.2: Operational Logic in Drain Mode (Sewage Pit Examp르).
6. 유지관리
Regular maintenance ensures the longevity and reliable operation of your Ortis controller.
- 센서 청소: Periodically inspect and clean the stainless steel sensors to remove any buildup of debris, algae, or mineral deposits that could affect their accuracy. Disconnect power before cleaning.
- 케이블 검사: Check all cables and connections for signs of wear, damage, or corrosion. Replace any damaged components immediately.
- 컨트롤러 유닛: Keep the controller unit clean and dry. Avoid exposing it to direct sunlight or extreme temperatures.
- 테스트 작업: Periodically test the controller's operation by manually raising or lowering water levels to ensure the pump activates and deactivates as expected in the selected mode.
7. 문제 해결
일반적인 문제와 해결 방법은 아래 표를 참조하세요.
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| Pump does not turn on/off automatically. | 1. Controller not in AUTO mode. 2. Sensors are dirty or improperly positioned. 3. Pump is not plugged in or is faulty. | 1. Ensure the switch is set to 'AUTO'. 2. Clean sensors and verify their high/low positions. 3. Check pump connection and functionality. |
| 알람이 자주 울립니다. | 1. Water level not reaching desired sensor within expected time. 2. 센서 오작동. 3. Alarm sensitivity setting (if applicable, check product documentation). | 1. Check pump operation and water flow. Adjust sensor positions if needed. 2. Inspect sensors for damage or debris. Replace if faulty. 3. Use the 'Mute' button temporarily. Consult manufacturer for alarm logic details. |
| 컨트롤러에 전원이 없습니다. | 1. 전원 코드가 뽑혀 있습니다. 2. 콘센트에 전원이 공급되지 않습니다. 3. 내부 퓨즈가 끊어졌습니다. | 1. Ensure power cord is securely plugged in. 2. Test the outlet with another device. Check circuit breaker. 3. 도움이 필요하면 고객지원팀에 문의하세요. |
| Pump runs continuously in AUTO mode. | 1. Sensor stuck in 'on' position (e.g., upper sensor always wet in Drain Mode). 2. 컨트롤러 고장. | 1. Clean and reposition sensors. Ensure they can freely detect water level changes. 2. Disconnect power and reconnect. If issue persists, contact support. |
8. 사양
그림 8.1: 컨트롤러 크기.
| 특징 | 사양 |
|---|---|
| 모델 | 케이제이-033 |
| 상표 | 오르티스 |
| 입력 Voltage | 220V / 110V 교류 |
| 출력 전류 | 15A |
| 최대 부하 전력 | 최대 2마력 |
| 센서 소재 | 스테인리스 스틸 |
| Adjustable Sensor Range | 1/2 inch to 20 inches |
| 제조업체 | FJKJ INC. |
9. 보증 및 지원
보증 정보 및 기술 지원은 제품 포장을 참조하거나 판매자/제조업체에 직접 문의하십시오. 구매 영수증을 구매 증빙 자료로 보관하십시오.
제조업체: FJKJ INC.