CLOVER D25-B-TL Touchless Water Cooler Purifier Dispenser User Manual

소개

Thank you for choosing the CLOVER D25-B-TL Touchless Water Cooler Purifier Dispenser. This advanced system provides convenient access to purified cold and ambient water. Featuring a GAC filtration system, UV LED self-cleaning, and touchless dispense technology, it ensures a hygienic and refreshing hydration experience. This manual provides essential information for proper setup, operation, maintenance, and troubleshooting to ensure optimal performance and longevity of your dispenser.

그림 1: 전면 view of the CLOVER D25-B-TL Water Cooler Dispenser.

중요한 안전 정보

기기를 사용하기 전에 모든 지침을 주의 깊게 읽어 주십시오. 나중에 참고할 수 있도록 이 설명서를 보관하십시오.

• 전기 안전: Ensure the dispenser is connected to a grounded electrical outlet. Do not use extension cords. Disconnect power before cleaning or servicing.
• 물 연결: 정수기는 반드시 식수 공급 장치에만 연결하십시오. 누수를 방지하기 위해 모든 연결부가 단단히 고정되었는지 확인하십시오.
• 놓기: Place the dispenser on a flat, stable surface. Allow adequate clearance around the unit for ventilation.
• 어린이와 애완동물: Keep children and pets away from the dispenser, especially during operation and maintenance.
• 온도: This unit dispenses cold and ambient water only. It does NOT produce hot water.
• 손상: Do not operate the dispenser if it has a damaged cord or plug, or if it has been dropped or damaged in any way. Contact customer support.

패키지 내용

Verify that all items listed below are included in your package.

• CLOVER D25-B-TL Water Cooler Dispenser
• First Filter (GAC Purification System)
• 물 배관
• 커넥터
• Emergency Shutoff Valve
• Tubing Clips
• 사용자 설명서

Figure 2: Included installation kit components.

설치 지침

1. 짐 풀기: Carefully remove the dispenser and all components from the packaging. Retain packaging for future transport if needed.
2. 놓기: Position the freestanding dispenser on a level, stable surface. Ensure there is adequate space around the unit for proper ventilation, especially at the rear where the cooling coils are located. The dimensions are approximately 13.58"D x 12.2"W x 43.3"H.
3. 필터 설치 :
   • Locate the filter housing, typically at the rear or bottom access panel of the unit.
   • Insert the provided GAC purification filter into the housing as per the arrows indicating water flow.
   • Secure the filter firmly.
   

   그림 3: 내부 view illustrating filter placement and water tubing.
4. 급수 연결:
   • Connect the water tubing from your potable water source to the dispenser's inlet using the provided connectors and emergency shutoff valve.
   • Ensure all connections are tight to prevent leaks. Use tubing clips to secure the tubing if necessary.
   • Slowly open the water supply valve to allow water to fill the dispenser's internal tank. Check for any leaks.
5. 전원 연결: 분배기를 접지된 120V AC 전기 콘센트에 꽂으세요.
6. 초기 플러시: Before first use, dispense several cups of water from both cold and ambient spouts to flush the system and filter. Discard this water.

작동 지침

The CLOVER D25-B-TL features touchless dispense and UV LED self-cleaning for enhanced hygiene.

1. 전원 켜기: Once plugged in, the dispenser will begin to cool the water. Allow approximately 1-2 hours for the water to reach optimal cold temperature (35.6°F).
2. Dispensing Water (Touchless):
   • Place your cup or container under the desired spout (cold or ambient).
   • Wave your hand in front of the sensor located above the spout. The water will begin to dispense.
   • Remove your hand to stop the water flow.
   

   Figure 4: Detail of the touchless dispense spouts and sensors.

3. UV LED Self-Cleaning: The dispenser is equipped with a UV LED self-cleaning system for enhanced water purification. This system operates automatically to maintain the hygiene of the internal water tanks. Refer to the indicator lights on the top panel for its status.

유지

Regular maintenance ensures the best performance and water quality from your dispenser.

1. 필터 교체:
   • The GAC purification filter should be replaced periodically, typically every 6 months or as indicated by the dispenser's filter change indicator (if present).
   • Turn off the water supply and unplug the dispenser before replacing the filter.
   • Follow the filter installation steps in the Setup section to replace the old filter with a new one.
   • Flush the new filter as described in the Initial Flush step.
2. 물받이 청소: The ABS drip tray is easily removed for cleaning.
   • Pull the drip tray forward to remove it.
   • Empty any collected water and wash the tray with mild soap and water.
   • Rinse thoroughly and reinsert the tray.
3. 외부 청소: 부드러운 d로 외부 표면을 닦으십시오.amp 천. 연마성 세척제나 용매를 사용하지 마십시오.
4. 탱크 내부 청소: The UV LED self-cleaning system helps maintain internal hygiene. For additional cleaning, consult the manufacturer's website or customer support for specific instructions.

문제 해결

고객 지원팀에 문의하기 전에 다음의 일반적인 문제와 해결책을 참조하세요.

명세서

그림 5: 제품 배치 참고용 치수.

보증 및 고객 지원

For warranty information, product registration, or technical assistance, please contact CLOVER customer support.

제조업체: 클로버
Web대지: CLOVER Official Store (일반적인 제품 정보)
구체적인 보증 조건 및 연락처는 구매 서류를 참조하십시오.