소개
Thank you for choosing the BIG RED T830025-1 Heavy Duty Hydraulic Steel Service Floor Jack. This manual provides important information for the safe operation, maintenance, and troubleshooting of your new floor jack. Please read and understand all instructions before use to ensure proper function and prevent injury or damage.
Image: The BIG RED T830025-1 Floor Jack, a red hydraulic jack with a black handle and wheels.
안전 정보
경고: 이 지침을 따르지 않으면 심각한 부상이나 재산 피해를 입을 수 있습니다.
- Always read and understand the entire manual before operating the jack.
- 정격 용량인 3톤(6,000파운드)을 초과하지 마십시오.
- 단단하고 평평한 표면에서만 사용하십시오.
- Always use jack stands to support the vehicle immediately after lifting. The jack is a lifting device only, not a vehicle support device.
- Ensure the vehicle is in park (or gear for manual transmission) and the parking brake is engaged. Block wheels that are not being lifted.
- 잭의 받침대 중앙에 하중을 놓으십시오. 하중이 중앙에 있지 않으면 잭이 넘어질 수 있습니다.
- 손과 발이 움직이는 부품이나 차량 하부에 닿지 않도록 하십시오.
- Do not modify the jack or use it for purposes other than its intended use.
- 안전 안경 등 적절한 개인 보호 장비를 착용하세요.
- Inspect the jack before each use for any damage, leaks, or loose parts. Do not use if damaged.
- 천천히 조심스럽게 하중을 내립니다.
설정 및 초기 준비
Before using your BIG RED T830025-1 floor jack, ensure it is properly assembled and prepared.
- 손잡이를 연결하세요: Insert the two handle sections together. Place the assembled handle into the handle socket on the jack.
- 손잡이를 단단히 고정하세요: Turn the handle clockwise until it is fully tightened and secured in the socket. This also closes the release valve for lifting.
- Purge Air from Hydraulic System (Bleeding):
- With the jack fully lowered, remove the oil filler plug (if present, refer to diagram in full manual).
- Pump the handle rapidly 10-15 times without a load.
- Replace the oil filler plug. This helps remove any trapped air.
Image: Diagram showing the wide lifting range and steps for connecting the handle and pumping to raise the saddle.
작동 지침
플로어잭을 안전하고 효율적으로 사용하려면 다음 단계를 따르십시오.
차량 들어올리기:
- 차량 준비: Park the vehicle on a hard, level surface. Engage the parking brake and place the transmission in park (or lowest gear for manual). Block the wheels that are not being lifted.
- 잭 위치: Roll the jack under the vehicle, positioning the saddle directly under the manufacturer's recommended lifting point. Consult your vehicle's owner's manual for proper lifting points.
- 차량 들어올리기: With the handle fully tightened clockwise (release valve closed), pump the handle up and down to raise the saddle. Continue pumping until the vehicle is lifted to the desired height.
- 잭 스탠드를 설치하세요: Immediately after lifting, place appropriately rated jack stands under the vehicle's frame or designated support points. Ensure the vehicle is securely resting on the jack stands before performing any work.
- Slightly Lower Jack: Once jack stands are in place, slowly turn the handle counter-clockwise to slightly lower the jack until the vehicle's weight is fully supported by the jack stands. The jack should remain in contact with the vehicle as a secondary safety measure.
차량 높이 낮추기:
- Raise Vehicle Slightly: Pump the jack handle a few times to lift the vehicle slightly off the jack stands.
- 잭 스탠드를 제거하세요: 차량 아래에서 잭 스탠드를 조심스럽게 제거하십시오.
- 하부 차량: Slowly turn the handle counter-clockwise to open the release valve. The vehicle will begin to lower. Control the lowering speed by adjusting how much you turn the handle.
- 잭을 제거하세요: Once the vehicle is fully lowered to the ground, remove the floor jack.
Image: Illustration of the jack's steel front wheels, 360-degree rotation casters, and its 6000 lbs rated capacity for cars, pickups, and MPVs. A warning states the product is a lifting tool only and requires jack stands for under-vehicle work.
유지
Regular maintenance ensures the longevity and safe operation of your floor jack.
- 매끄럽게 하기: 모든 움직이는 부품에 주기적으로 가벼운 기계유를 사용하여 윤활하십시오.
- 유압 오일 레벨: Check the hydraulic oil level every three months. With the jack fully lowered and on a level surface, remove the oil filler plug. The oil level should be just below the filler hole. Add high-quality hydraulic jack oil if needed. Do not overfill.
- 청소: 잭에 먼지, 기름때, 부식성 물질이 묻지 않도록 깨끗하게 유지하십시오.
- 저장: Store the jack in a dry, protected area with the ram fully retracted to prevent rust and seal damage.
- 점검: Before each use, inspect for any signs of damage, leaks, or wear. Pay close attention to welds, wheels, and the hydraulic cylinder.
문제 해결
This section addresses common issues you might encounter with your floor jack.
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 잭은 짐을 들어 올리지 않습니다. |
|
|
| 잭은 천천히 또는 불규칙적으로 들어 올립니다. |
|
|
| Jack leaks hydraulic fluid. |
|
|
| 잭은 낮추지 않을 것이다. |
|
|
명세서
Key technical specifications for the BIG RED T830025-1 Floor Jack.
- 모델: T830025-1
- 상표: 큰 빨간
- 용량: 3톤(6,000파운드)
- 재료: 합금강
- 최소 들어올리기 높이: 5-1/8인치(13.0cm)
- 최대 리프팅 높이: 18-5/16인치(46.5cm)
- 제품 크기(길이 x 너비 x 높이): 22.5인치 x 12.9인치 x 6.90인치(57.2 x 32.8 x 17.5cm)
- 손잡이 길이: 39.3인치(99.8cm)
- 품목 무게: 27.34kg(60.27파운드)
- 차량 서비스 유형: Car, Light Trucks, SUVs
- 특징: Single Piston Quick Lift Pump, Detachable Handle, Foam Bumper, 360-degree Swivel Casters, Built-in Safety Valve.
Image: Detailed product specification diagram showing the jack's dimensions, minimum and maximum lifting heights, and handle length.
보증 및 지원
This BIG RED T830025-1 Floor Jack comes with a 1년 보증 구매일로부터 정상적인 사용 중에 발생한 재료 및 제조상의 결함을 보장합니다.
For warranty claims, technical assistance, or to order replacement parts, please contact BIG RED customer support. Keep your purchase receipt as proof of purchase.
Contact information for BIG RED customer support can typically be found on the manufacturer's official web사이트 또는 제품 포장에 표시되어 있습니다.