CERAKOTE C-SERIES GLACIER BLACK (C-7600P) Instruction Manual

1. 서론

This manual provides detailed instructions for the proper use and application of CERAKOTE C-SERIES GLACIER BLACK (C-7600P) air cure ceramic coating. This product is designed to provide a durable, high-performance finish with exceptional chemical resistance and UV stability on various substrates, including metals and polymers.

CERAKOTE C-SERIES coatings are air-cured and ready to spray, requiring no additional catalyst. The Glacier Black (C-7600) variant offers a deep black, sleek satin finish.

2. 안전 정보

WARNING: This product is a chemical coating. Always follow safety precautions.

• 통풍: Use in a well-ventilated area or outdoors. Avoid inhaling vapors.
• 개인 보호 장비(PPE): Wear appropriate chemical-resistant gloves, eye protection (safety glasses or goggles), and a respirator suitable for organic vapors.
• 피부 접촉: 장시간 또는 반복적인 피부 접촉을 피하십시오. 취급 후에는 비누와 물로 깨끗이 씻으십시오.
• 눈맞춤: 눈에 들어갔을 경우 즉시 흐르는 물에 15분 이상 충분히 헹구고 의사의 진료를 받으십시오.
• 음식물 섭취: 절대 삼키지 마십시오. 삼켰을 경우, 억지로 구토를 유발하지 마십시오. 즉시 의료진의 진료를 받으십시오.
• 인화성: Keep away from open flames, sparks, and hot surfaces.
• 저장: 직사광선과 상충되는 물질을 피해 서늘하고 건조한 곳에 보관하십시오. 사용하지 않을 때는 용기를 꼭 닫아 두십시오.

3. 제품 오버view

The CERAKOTE C-SERIES GLACIER BLACK (C-7600P) is an advanced air-cured ceramic coating formulated for high-temperature applications and environments where extreme durability is required. It provides a deep black, satin finish that maintains its aesthetic and protective qualities under harsh conditions.

주요 특징:

• Air-cured, ready-to-spray formula.
• No catalyst required.
• Deep black, sleek satin finish.
• Extremely high chemical resistance.
• UV resistant.
• PFAS free formulation.

Figure 1: CERAKOTE C-7600 Glacier Black 16oz bottle. Note the 'C-Series Coating' and 'Glacier Black' labels, and the 'Important: Solids will settle! Must shake well for proper application' warning.

Figure 2: PFAS Free logo, indicating the product's environmental compliance.

4. 설치 및 표면 준비

Proper surface preparation is critical for optimal adhesion and performance of CERAKOTE coatings. Do not skip or rush these steps.

4.1. 필수 장비

• HVLP or conventional spray gun with appropriate nozzle size (e.g., 0.8mm - 1.4mm).
• Air compressor with moisture separator.
• Abrasive blasting equipment (optional, but recommended for optimal adhesion on metals).
• Degreaser (e.g., acetone, MEK, or specialized Cerakote degreaser).
• Clean, lint-free cloths.
• Personal Protective Equipment (PPE) as outlined in Section 2.

4.2. Surface Preparation Steps

1. 분해 : Disassemble the item to be coated into its individual components.
2. 정도asing: Thoroughly degrease all surfaces using a suitable degreaser. Ensure all oils, greases, and contaminants are removed. Repeat if necessary.
3. Abrasive Blasting (for Metals): For optimal adhesion on metal substrates, abrasive blast the surface using 100-120 grit aluminum oxide at 80-100 PSI. This creates a profile for the coating to adhere to. Avoid blasting polymers unless specified by the manufacturer.
4. 최종 세척: After blasting (if applicable), re-degrease the surface to remove any blasting media residue or new contaminants. Use clean, lint-free cloths.
5. 건조: Ensure the surface is completely dry before application. Use compressed air to blow out any crevices.

4.3. Product Preparation

• 잘 흔들어주세요: CERAKOTE C-SERIES coatings contain solids that will settle. Shake the bottle vigorously for at least 5 minutes before use to ensure a uniform mixture.
• No Catalyst: This C-Series product is air-cured and does not require a catalyst. Do not add any.
• Strain (Optional): For best results, strain the coating through a 100-190 micron filter before pouring into the spray gun cup to prevent clogs.

5. 사용 설명서(응용 프로그램)

Apply CERAKOTE C-SERIES GLACIER BLACK in a controlled environment, maintaining consistent temperature and humidity if possible.

5.1. Spray Gun Settings

• 공기압: Typically 20-30 PSI at the gun, depending on the gun type and desired atomization. Adjust as needed for a fine, even spray pattern.
• Fluid Control: Adjust to achieve a consistent flow without excessive material.

5.2. Application Technique

1. Hold the spray gun 4-6 inches (10-15 cm) from the surface.
2. Apply thin, even coats with overlapping passes. Avoid heavy coats, which can lead to runs or uneven curing.
3. Allow 5-10 minutes flash time between coats, or until the surface appears matte and no longer wet.
4. Typically, 1-2 coats are sufficient to achieve full coverage and desired film thickness.
5. Ensure all surfaces are evenly coated.

5.3. Curing Process

• CERAKOTE C-SERIES GLACIER BLACK is an air-cure coating. It will be dry to the touch within 24 hours at ambient temperatures (60-75°F / 15-24°C).
• Full cure and maximum hardness are achieved over a period of 5-7 days. Handle coated items carefully during this initial curing period.
• Do not expose to harsh chemicals or extreme abrasion until fully cured.

6. 유지관리

Once fully cured, CERAKOTE C-SERIES GLACIER BLACK is highly durable and requires minimal maintenance.

• 청소: Clean coated surfaces with mild soap and water. Avoid abrasive cleaners or harsh solvents, especially during the initial cure period.
• 보호: While highly resistant, avoid unnecessary impact or scratching to preserve the finish.

7. 문제 해결

This section addresses common issues that may arise during application.

8. 사양

9. 보증 및 지원

For specific warranty information regarding CERAKOTE C-SERIES GLACIER BLACK (C-7600P), please refer to the official CERAKOTE website or contact their customer support directly. Warranty terms typically cover manufacturing defects and may vary based on purchase location and application.

고객 지원:

• 기술 지원, 제품 문의 또는 기타 지원이 필요하시면 공식 웹사이트를 방문하십시오. 세라코트 web대지.
• 제조업체에 문의하십시오. website for the most up-to-date contact information and detailed application guides.