Morimoto Sealed4 4x6 LED Headlight Instruction Manual

소개

The Morimoto Sealed4 LED headlights are designed as a high-performance replacement for 4x6 inch sealed beam headlights. These units feature advanced LED technology and precision optics to deliver superior illumination for various vehicle applications. They are DOT approved and compatible with standard H4651, H4652, H4656, H4666, and H6545 headlight types.

영상: 앞쪽 view of the Morimoto Sealed4 4x6 LED Headlight, showcasing its clear lens and internal LED projectors.

안전 정보

• 감전이나 손상을 방지하기 위해 전기 작업을 하기 전에 항상 차량 배터리를 분리하십시오.
• 설치 작업 중에는 안전 고글과 장갑을 포함한 적절한 개인 보호 장비를 착용하십시오.
• 모든 배선 연결이 안전하고 적절하게 절연되어 단락을 방지하세요.
• Do not look directly into the LED light source when illuminated, as it can cause eye strain or damage.
• 설치 과정 중 확실하지 않은 부분이 있으면 자격을 갖춘 자동차 정비사에게 문의하십시오.

패키지 내용

설치를 시작하기 전에 모든 구성 요소가 있고 손상되지 않았는지 확인하세요.

• Pair of Morimoto Sealed4 4x6 LED Headlight Assemblies
• Universal Wiring (H4 3-pin male inputs)

설정 및 설치

The Morimoto Sealed4 headlights are designed for a direct replacement of existing 4x6 inch sealed beam headlights, featuring H4 3-pin male inputs for a plug-and-play installation in most compatible vehicles.

1. 준비: 차량을 평평한 곳에 주차하고 주차 브레이크를 걸십시오. 차량 배터리의 음극 단자를 분리하십시오.
2. 기존 헤드라이트를 제거하세요: Carefully remove the bezel or trim surrounding the existing 4x6 inch headlights. Disconnect the wiring harness from the back of the old headlight and remove any retaining clips or screws holding it in place. Gently pull out the old headlight unit.
3. 새 헤드라이트를 연결하세요: Connect the H4 3-pin male input of the Morimoto Sealed4 LED headlight to the vehicle's existing H4 wiring harness. Ensure the connection is secure.
4. 새 헤드라이트 설치: Insert the Morimoto Sealed4 LED headlight into the headlight bucket. Secure it using the original retaining clips or screws. Ensure the headlight is seated properly and firmly.
5. 테스트 기능: Reconnect the vehicle's battery. Turn on the headlights (low beam and high beam) and check for proper operation. Verify that both headlights illuminate correctly and switch between low and high beams.
6. Aiming (if necessary): If the beam pattern appears incorrect, refer to your vehicle's service manual or local regulations for proper headlight aiming procedures.
7. 최종 조립: Reinstall any bezels or trim removed earlier.

영상: 뒤쪽 view of the Morimoto Sealed4 headlight, showing the integrated heat sink and the H4 3-pin connector for easy installation.

영상: Technical drawing illustrating the dimensions and LED component layout of the Morimoto Sealed4 headlight, including low beam and high beam LED positions.

작동 지침

The Morimoto Sealed4 LED headlights provide distinct low and high beam functionalities for optimal road illumination.

• 로우 빔: When activated, the low beam utilizes NCSW170C Series LEDs and Morimoto's Kuria Optic projector lens array to produce a precisely controlled 2400 lumen output with a Left-Hand Drive (LHD) stepped beam pattern. This pattern is designed to illuminate the road ahead without causing glare to oncoming traffic.
• 하이 빔: Switching to high beam mode engages additional LEDs, increasing the total light output to an impressive 4300 lumens. The high beam provides maximum illumination for improved visibility on unlit roads or when additional light is required.

영상: Illustration of the Morimoto Sealed4 low beam pattern projected onto a wall, demonstrating the sharp cutoff and wide spread.

영상: Illustration of the Morimoto Sealed4 high beam pattern projected onto a wall, showing the increased light output and extended throw.

유지

The Morimoto Sealed4 LED headlights are designed for durability and minimal maintenance.

• 청소: Clean the UV-coated polycarbonate lenses with a soft cloth and mild soap and water. Avoid abrasive cleaners or harsh chemicals that could damage the lens coating.
• 점검: Periodically inspect the headlights for any signs of damage, loose connections, or debris accumulation.
• 열 관리: The heavy-duty die-cast housings are designed to act as efficient heat sinks, ensuring optimal LED performance and longevity. No user maintenance is required for heat management.

문제 해결

명세서

보증 정보

The Morimoto Sealed4 LED Headlights are backed by a 5년 제조사 보증. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims. For specific terms and conditions, refer to the official Morimoto warranty documentation or contact customer support.

지원하다

For technical assistance, troubleshooting, or warranty inquiries, please contact Morimoto customer support. You can find contact information on the official Morimoto web사이트 또는 공인 딜러를 통해 구매하세요.

온라인 리소스: Visit the Morimoto Store on Amazon

제품 비디오