JONSBO N2 NAS ITX 케이스 사용 설명서

1. 서론

This manual provides detailed instructions for the installation, operation, and maintenance of your JONSBO N2 NAS ITX Case. The JONSBO N2 is a compact aluminum chassis designed for Network Attached Storage (NAS) or mini PC builds, supporting up to five 3.5-inch hard disk drives and one 2.5-inch solid-state drive.

Image 1.1: JONSBO N2 NAS ITX Case with internal drive bays highlighted.

2. 설정 및 설치

Follow these steps to assemble your JONSBO N2 NAS ITX Case with your components.

2.1. 준비

Before beginning, ensure you have the following components:

• ITX 마더보드
• SFX Power Supply (maximum 150mm length)
• 3.5-inch Hard Disk Drives (up to 5)
• 2.5-inch Solid State Drive (1)
• 로우 프로file PCI Expansion Card (optional, maximum 197mm length)
• CPU Cooler (maximum 65mm height)
• 드라이버 세트
• Cable ties for management

2.2. Case Disassembly

The JONSBO N2 features a removable top cover and a magnetic front panel for easy access.

1. Gently pull the magnetic front panel to detach it from the chassis.
2. Remove the screws securing the top cover and slide it off to expose the motherboard tray.

Image 2.1: Front panel removed, showing drive bays.

2.3. 메인보드 및 CPU 쿨러 설치

1. Install your ITX motherboard onto the motherboard tray using the provided standoffs and screws.
2. Install your CPU cooler. Ensure its height does not exceed 65mm to allow the top cover to close properly.

2.4. 전원 공급 장치 설치

1. Mount the SFX power supply into its designated bracket. The power supply should not exceed 150mm in length.
2. 나사로 전원 공급장치를 고정합니다.

2.5. 드라이브 설치

The JONSBO N2 supports five 3.5-inch hot-swappable HDDs and one 2.5-inch SSD.

1. 3.5인치 HDD: Attach the provided handles and rubber slides to each 3.5-inch HDD. Slide each drive into an available hot-swappable bay until it clicks into place.
2. 2.5-inch SSD: Mount the 2.5-inch SSD in its dedicated slot, typically located behind the motherboard tray or within the drive cage structure.
3. Connect SATA data and power cables to all installed drives.

이미지 2.2: 폭발 view illustrating component and drive installation.

2.6. 확장 카드 설치

로우프로를 사용하는 경우file PCI expansion card:

1. Remove the appropriate PCI slot cover from the rear of the case.
2. Insert the low-profile expansion card into the motherboard's PCI-E slot. The card length must not exceed 197mm.
3. 카드를 나사로 고정하세요.

2.7. Front Panel and Cooling Connections

1. Connect the front panel headers (USB 3.2 Gen2 Type-C, USB 3.0, Audio+Mic, Power/Reset) to the corresponding pins on your motherboard.
2. Ensure the pre-installed rear 120mm fan is connected to a fan header on your motherboard for proper cooling.

2.8. Cable Management and Reassembly

1. Route all cables neatly to ensure optimal airflow and prevent interference with components. Use cable ties as needed.
2. Slide the top cover back into place and secure it with screws.
3. Reattach the magnetic front panel.

3. 사용 설명서

3.1. 전원 켜기/끄기

Press the power button located on the front panel to turn the system on or off. Follow your operating system's shutdown procedures for safe power-off.

3.2. Hot-Swapping Drives

The JONSBO N2 supports hot-swapping for its 3.5-inch HDD bays. Ensure your motherboard and operating system are configured to support hot-swapping before attempting this procedure.

1. Safely eject the drive from your operating system.
2. Gently pull the handle of the desired drive bay to release and remove the drive.
3. Insert a new 3.5-inch HDD into the empty bay, ensuring it slides in smoothly until it locks into place.
4. The operating system should detect the new drive.

4. 유지관리

Regular maintenance helps ensure the longevity and optimal performance of your JONSBO N2 case and its components.

4.1. 청소

1. 외부: Wipe the aluminum exterior with a soft, damp 옷감. 연마성 세제를 피하십시오.
2. 먼지 필터: The case includes dust filters. Periodically remove and clean them with water or compressed air. Ensure they are completely dry before reinstallation.
3. 내부 구성 요소: Use compressed air to gently remove dust from internal components, especially the fan blades and heatsinks. Perform this with the system powered off and unplugged.

Image 4.1: Rear fan and filter assembly.

4.2. 환기

Ensure that all ventilation grilles on the case are unobstructed to maintain proper airflow and prevent overheating. Avoid placing the case in enclosed spaces without adequate air circulation.

Image 4.2: Product details including ventilation grille and rear fan.

5. 문제 해결

This section addresses common issues you might encounter with your JONSBO N2 case.

5.1. 힘이 없다

• Verify that the power supply is securely connected to the wall outlet and the motherboard.
• Check that the front panel power button header is correctly connected to the motherboard.
• Ensure the power supply unit (PSU) switch is in the 'ON' position.

5.2. 과도한 팬 소음

• Check if the fan blades are obstructed by cables or dust.
• 팬이 단단히 장착되었고 케이스에 진동이 발생하지 않는지 확인하세요.
• If the stock 120x15mm fan is too loud, consider replacing it with a quieter aftermarket fan of the same dimensions.

5.3. 드라이브가 감지되지 않음

• Ensure all SATA data and power cables are securely connected to both the drives and the motherboard/PSU.
• For 3.5-inch HDDs, confirm they are fully seated in their hot-swappable bays.
• Check your motherboard's BIOS/UEFI settings to ensure SATA ports are enabled.

5.4. 과열

• Verify that the rear 120mm fan is operating correctly.
• 공기 흐름 방해를 줄이기 위해 케이블 관리를 개선하십시오.
• Ensure the case's ventilation grilles are clear of obstructions.

6. 사양

Detailed technical specifications for the JONSBO N2 NAS ITX Case:

Image 6.1: Chassis parameters and dimensions.

7. 보증 및 지원

JONSBO products are manufactured to high-quality standards. For specific warranty information regarding your JONSBO N2 NAS ITX Case, please refer to the warranty card included with your purchase or visit the official JONSBO web대지.

If you encounter any issues or require technical assistance, please contact JONSBO customer support through their official channels. Provide your product model (N2) and a detailed description of the issue for efficient service.