타이탄 피트니스 X-3 시리즈 플랫 풋 파워랙 (높이 91인치, 깊이 30인치) 사용 설명서

소개

The X-3 Series Flat Foot Power Rack by Titan Fitness is offered in 82 and 91-inch models to fit your gym needs. Featuring heavy-duty 3 x 3-inch 11-gauge square steel uprights with Westside hole spacing through the bench and clean pull zone, 2-inch spacing above and below, 6-inch side hole spacing throughout entire upright, a bolt-together design, and a powder-coated black finish. Additionally, the power rack comes standard with a 1.25-inch pull-up bar, a 2-inch fat pull-up bar, and (2) reinforced J-Hooks. This power rack is designed for lifters and athletes seeking a high-quality solution without the need to bolt the rack to the floor.

앞쪽 view of the Titan Fitness X-3 Series Flat Foot Power Rack, showcasin견고한 디자인 덕분입니다.

안전 정보

• 새로운 운동 프로그램을 시작하기 전에 반드시 의료 전문가와 상담하세요.
• 사용하기 전에 모든 부품에 손상이 있는지 검사하십시오. 부품이 손상되었거나 누락된 경우 사용하지 마십시오.
• Ensure all bolts and fasteners are securely tightened before use. Regularly check and re-tighten as necessary.
• Maintain a clear area around the power rack during use to prevent accidents.
• Do not exceed the maximum weight capacities: Rackable Capacity: 1,650 lb., Whole Rack Capacity: 6,170 lb.
• Two-person assembly is recommended for safety.
• Keep children and pets away from the equipment during assembly and use.
• Use appropriate safety spotters or safety straps when lifting heavy weights.

구성품 목록

조립을 시작하기 전에 모든 부품이 있는지 확인하십시오.

• (4) Heavy-duty steel uprights (3 x 3-inch 11-gauge steel)
• (2) J-Hooks with UHMW plastic
• (1) 1.25-inch Single Pull-Up Bar
• (1) 2-inch Fat Pull-Up Bar
• 조립용 하드웨어(너트, 볼트, 와셔)
• (3) Topside Bracings
• Flat Foot Base components

설정 및 조립

Tools required: Adjustable wrench or socket set.

1. 구성 요소 풀기: Carefully remove all parts from the packaging and lay them out. Verify against the components list.
2. 베이스 조립: Connect the flat foot base components to the bottom of the uprights using the provided hardware. Ensure the base is stable and level.
   

   Image showing the assembled base of the power rack with uprights.

3. 기둥을 부착하세요: Securely attach the four uprights to the assembled base. Ensure the Westside hole spacing (closer holes) is oriented correctly for bench and clean pull zones.
   

   Detail of the upright showing Westside hole spacing for precise adjustments.

4. Install Top Bracings: Connect the three topside bracings between the uprights at the top of the rack. This provides structural integrity.
   

   View of the top bracings and pull-up bars installed, securing the upper frame.
5. Mount Pull-Up Bars: Install the 1.25-inch single pull-up bar and the 2-inch fat pull-up bar to the designated positions on the top bracings. Choose the bar that best suits your grip preference.
6. Attach J-Hooks: Insert the J-Hooks into the desired holes on the uprights. Ensure the UHMW plastic is facing inwards to protect your barbell.
   

   A J-hook securely attached to an upright, ready for barbell placement.

7. 최종 조임: Once all components are in place, systematically tighten all nuts and bolts. Do not overtighten, but ensure a secure fit.
8. 안정성 확인: Gently shake the assembled rack to ensure it is stable and does not wobble. Adjust as necessary.

작동 지침

• Barbell Placement: Place your barbell securely onto the J-Hooks. Ensure the barbell is centered and stable before loading weights.
  

  A barbell with weight plates resting securely on a J-hook within the power rack.
• J-훅 조정하기: To adjust the height of the J-Hooks, remove the barbell, lift the J-Hook, pull it out, and re-insert it into the desired hole. Ensure both J-Hooks are at the same height.
• Using Pull-Up Bars: The 1.25-inch and 2-inch pull-up bars offer different grip challenges. Select the bar that suits your exercise. Ensure a firm grip before performing pull-ups.
• 액세서리 호환성: The X-3 Series Power Rack is compatible with various Titan Fitness X-3 accessories (e.g., Pin and Pipe Safeties, Spotter Arms, Roller J-Hooks). Refer to the accessory's specific instructions for installation and use.
  

  The power rack set up with a barbell, weight plates, and a bench, demonstrating its versatility for various exercises.

유지

• 정기 검사: Periodically inspect all bolts, nuts, and connections for tightness. Re-tighten as needed to ensure stability and safety.
• 청결: 광고로 강철 프레임을 닦으세요amp cloth to remove dust and sweat. Avoid abrasive cleaners that may damage the powder-coated finish.
• UHMW Plastic: Check the UHMW plastic on the J-Hooks for wear and tear. Replace if significantly damaged to protect your barbell.
• 저장: If disassembling for storage, keep all hardware organized to prevent loss.

문제 해결

명세서

보증 및 지원

For warranty information, please refer to the official Titan Fitness website or contact their customer support directly. The product comes with a 30-day easy returns policy.

For assistance with missing parts, assembly questions, or other inquiries, please contact Titan Fitness customer support. You can find their contact information on their official web대지: www.타이탄.피트니스

Customer Support is available for assistance.