Motoguard HP11 Motorcycle Handguards with LED Turn Signals - Instruction Manual

소개

This manual provides detailed instructions for the installation, operation, and maintenance of your Motoguard HP11 Motorcycle Handguards with integrated LED Turn Signals and Daytime Running Lights (DRL). These handguards are designed to offer enhanced protection against wind and rain, while improving visibility and safety through their integrated lighting features. Please read this manual thoroughly before installation and use.

안전 정보

• Always ensure the motorcycle is stable and turned off before beginning installation.
• 설치 시에는 장갑과 보안경 등 적절한 안전 장비를 착용하십시오.
• If you are unsure about any part of the installation process, consult a qualified motorcycle mechanic.
• 단락을 방지하기 위해 모든 전기 연결부가 단단히 고정되어 있고 적절하게 절연되어 있는지 확인하십시오.
• These handguards are a universal fit item. Verify dimensions and compatibility with your specific motorcycle model before permanent installation. Adjustments may be necessary.
• The LED turn signals and DRL are for enhanced visibility. They may not have ECE approval; check local regulations regarding auxiliary lighting.

패키지 내용

The Motoguard HP11 Handguards package includes:

• 1x Left Handguard with integrated LED lighting
• 1x Right Handguard with integrated LED lighting
• Universal Mounting Hardware (brackets, screws, spacers)

설정 및 설치

Follow these steps for proper installation of your Motoguard HP11 Handguards:

1. 준비: Park your motorcycle on a stable surface. Ensure the engine is off and the ignition key is removed.
2. Remove Existing Bar Ends (if applicable): If your motorcycle has existing bar end weights or mirrors mounted to the bar ends, carefully remove them.
3. 장착 브래킷을 조립하십시오: Attach the universal mounting brackets to the handguards. Ensure the orientation is correct for left and right sides.

   

4. Position Handguards: Slide the inner clamp of the handguard mounting system onto the handlebar, near the grip and controls. Position the outer end of the handguard into the handlebar end.

   

5. 조정 및 보안: Adjust the angle and position of the handguards to ensure they do not interfere with the operation of brake levers, clutch levers, or mirrors. Once satisfied with the position, securely tighten all mounting bolts. Do not overtighten.
6. Electrical Connection (LEDs): Proceed to the "Operating LED Functions" section for wiring instructions.

Operating LED Functions

The Motoguard HP11 Handguards feature integrated LED turn signals and Daytime Running Lights (DRL). These can be connected to your motorcycle's electrical system for enhanced visibility.

• 방향 지시등: Identify the wiring for your motorcycle's existing turn signals. Connect the corresponding wires from the handguards (typically yellow or orange) to the positive (+) wire of your motorcycle's turn signals. Connect the ground wire (typically black) to a suitable ground point on the motorcycle.
• 주간 주행등(DRL): For the DRL function, connect the dedicated DRL wire (typically white or red) from the handguards to a switched 12V power source on your motorcycle that is active when the ignition is on. Connect the ground wire (typically black) to a suitable ground point.
• 테스트: After making all connections, turn on your motorcycle's ignition and test the turn signals and DRL to ensure they function correctly.
• 격리: Ensure all electrical connections are properly insulated using electrical tape or heat shrink tubing to protect against moisture and short circuits.

메모: The LED functions are optional and do not have ECE approval. Always check local regulations regarding auxiliary lighting on motorcycles.

유지

• 청소: Clean the handguards regularly with mild soap and water. Avoid abrasive cleaners or solvents that could damage the plastic or LED lenses.
• 점검: Periodically check all mounting bolts for tightness. Vibrations from riding can loosen fasteners over time.
• 배선: Inspect the wiring for any signs of wear, fraying, or damage. Repair or replace damaged wiring immediately to prevent electrical issues.

문제 해결

• LED가 작동하지 않음:
  • Check all electrical connections for proper contact and insulation.
  • Ensure the ground wire is securely connected to a good ground point.
  • Verify that the power source for the DRL (if connected) is active when the ignition is on.
  • Check for blown fuses in your motorcycle's electrical system.
• Handguards Feel Loose:
  • 모든 고정 볼트를 조이십시오.
  • Ensure the inner clamp and bar end expander are properly seated and tightened.
• 제어 장치 간섭:
  • Loosen mounting bolts and readjust the position and angle of the handguards.
  • Ensure there is sufficient clearance for full movement of brake/clutch levers and throttle.

명세서

지원하다

For further assistance or inquiries, please refer to the retailer where you purchased this product. Always ensure to provide your product model number (am-A140468) for efficient support.