Lewisia Replacement Pump BP800 for Solar Fountain Water Pump SP100 SP150LX User Manual

1. 서론

This manual provides essential instructions for the installation, operation, and maintenance of your Lewisia BP800 Replacement Water Pump. This pump is designed as a direct replacement for Lewisia Solar Fountain Pumps, specifically compatible with models BSV-SP100 and BSV-SP150LX, as well as other solar pumps that match the specifications and connection type.

Please read this manual thoroughly before installation and operation to ensure proper function and longevity of your pump.

2. 제품 오버view 및 구성 요소

The Lewisia BP800 is a compact and efficient water pump designed for solar-powered fountain systems. It features a durable ABS construction and a sealed connection cable for outdoor use.

Lewisia BP800 Replacement Pump, front view with water outlet and power cable

그림 1: 앞쪽 view of the Lewisia BP800 replacement pump, showing the water outlet, intake grille, and power cable with connector.

Lewisia BP800 Replacement Pump, side view 전원 케이블 포함

그림 2: 옆 view of the Lewisia BP800 replacement pump, illustrating the compact design and the power cable extending from the unit.

주요 구성 요소:

펌프 본체 : Encapsulates the motor and impeller.
물 출구: Top nozzle for connecting to fountain attachments or tubing.
Intake Grille: Located on the front/side, filters debris before water enters the pump.
전원 케이블 : Connects the pump to the solar panel or power source.
커넥터: Waterproof connector for secure attachment to the power source.

3. 사양

모델 번호	BP800
호환 모델	Lewisia BSV-SP100, BSV-SP150LX
재료	아크릴로니트릴 부타디엔 스티렌(ABS)
색상	검은색
전원	Solar Powered (requires compatible solar panel)
권tage	12 볼트
제품 크기(L x W x H)	3.95" x 2.6" x 2.6" (approximately 10.0 x 6.6 x 6.6 cm)
품목 무게	0.41킬로그램(약 14.4온스)
최대 리프팅 높이	0.5 Feet (approximately 15 cm)

4. 설정 및 설치

This pump is intended as a replacement unit. Ensure your existing solar panel and fountain system are compatible with the BP800 pump's specifications (12 Volts).

전원 분리: Before handling, ensure the solar panel is not exposed to direct sunlight or is disconnected from any power source to prevent accidental operation.
오래된 펌프 제거: Carefully remove the old pump from your fountain. Disconnect any tubing or fountain heads attached to it.
연결 검사: Check the power connector on your solar panel's cable to ensure it matches the connector on the BP800 pump.
튜빙 연결: Attach the appropriate tubing or fountain head to the water outlet nozzle of the new BP800 pump. Ensure a snug fit to prevent leaks.
위치 펌프: Place the new BP800 pump securely at the bottom of your fountain basin. Ensure it is fully submerged in water. The intake grille should be clear of any obstructions.
전원 연결: Connect the power cable of the BP800 pump to the corresponding cable from your solar panel. Ensure the connection is firm and waterproof.
테스트 작업: Once all connections are secure and the pump is submerged, expose the solar panel to direct sunlight. The pump should begin operating.

중요한: Never operate the pump dry. Always ensure the pump is fully submerged in water before connecting it to a power source.

5. 운영

The Lewisia BP800 pump is designed for continuous operation when sufficient sunlight is available to its connected solar panel. Its performance, including water flow and spray height, will vary directly with the intensity of sunlight.

햇빛 의존성: The pump will only operate when the solar panel receives direct and adequate sunlight. Performance will decrease on cloudy days or in shaded areas.
수위: Always maintain an adequate water level in your fountain to ensure the pump remains fully submerged. Running the pump dry can cause damage.
초기 시작: It may take a few moments for the pump to prime and begin pumping water effectively after initial setup or after being dry.

6. 유지관리

정기적인 유지관리를 통해 최적의 성능을 보장하고 펌프의 수명을 연장할 수 있습니다.

흡기 그릴 청소: Periodically check and clean the intake grille to remove any accumulated debris such as leaves, algae, or sediment. Blockages can reduce water flow and strain the pump motor.
임펠러 청소: If water flow is significantly reduced, the impeller may be clogged. Disconnect the pump from power, remove any attached tubing, and carefully open the pump housing (if designed for user access) to clean the impeller and its chamber. Refer to your original fountain manual for specific disassembly instructions if needed.
Maintain Water Quality: Keep fountain water clean to minimize algae growth and sediment buildup, which can clog the pump.
동계화(추운 기후용): In freezing temperatures, remove the pump from the fountain. Clean it thoroughly, dry it, and store it in a frost-free location until spring. Do not allow the pump to freeze in water.

7. 문제 해결

If your pump is not functioning correctly, refer to the following common issues and solutions:

문제	가능한 원인	해결책
펌프가 작동하지 않음	태양광 패널에 햇빛이 충분히 들어오지 않습니다. 전원 케이블이 분리되었거나 고장났습니다. Pump clogged with debris. Pump not submerged.	Move solar panel to direct sunlight. 모든 케이블 연결을 확인하십시오. Clean intake grille and impeller. 펌프가 물에 완전히 잠겨 있는지 확인하십시오.
Low water flow or weak spray	Partial blockage in pump or tubing. 햇빛이 부족합니다. Low water level in fountain.	Clean pump intake, impeller, and tubing. 태양광 패널이 직사광선을 충분히 받을 수 있도록 하십시오. Add water to the fountain until the pump is fully submerged.
펌프가 간헐적으로 작동함	Fluctuating sunlight (e.g., passing clouds). 전원 연결이 느슨합니다.	This is normal for solar pumps in variable light conditions. Check and secure power connections.

이러한 해결 방법을 시도한 후에도 문제가 지속되면 고객 지원팀에 문의하세요.

8. 보증 및 지원

Specific warranty information for the Lewisia BP800 Replacement Pump is not provided in this document. For details regarding warranty coverage, returns, or technical support, please refer to the original product packaging, your purchase receipt, or contact Lewisia customer service directly.

When contacting support, please have your product model number (BP800) and purchase information readily available.

Lewisia BP800

Lewisia Replacement Pump BP800 User Manual