소개
The Monkey Loop Floor Prime 3 Guitar Stand is designed to securely hold up to three acoustic, electric, or bass guitars. Constructed from durable alloy steel with protective rubber padding, this stand offers a compact and stable solution for organizing your instruments in a studio, on stage, or at home. Its foldable design allows for easy transport and storage.
안전 정보
- Ensure all components are securely fastened before placing instruments on the stand.
- 넘어지지 않도록 스탠드를 평평하고 안정적인 표면에 놓으십시오.
- Do not exceed the capacity of three guitars.
- Keep the stand away from high-traffic areas to avoid accidental bumps.
- Regularly inspect the stand for any signs of wear or damage to the frame or padding.
패키지 내용
Before assembly, verify that all parts are present:
- Main frame components (vertical supports, base bars, top support bar)
- Protective rubber padding/sleeves
- Assembly hardware (screws, Allen key) - Note: Some screws may be pre-inserted into the tubular components.
- 고무 발
조립 설명서
조립은 일반적으로 약 15분 정도 소요됩니다. 다음 단계를 주의 깊게 따르십시오.
- 구성 요소 풀기: Carefully remove all parts from the packaging. Check inside the tubular sections for any pre-inserted screws or small parts.
- 베이스 조립: Connect the base bars to the vertical support frames. Ensure the rubber padding is correctly oriented to protect the instrument bodies.
- 수직 지지대를 부착하세요: Secure the vertical support frames to the assembled base.
- 상단 지지대 설치: Attach the top support bar, which features the neck cradles, to the upper section of the vertical supports. Ensure the cradles are facing the correct direction to hold guitar necks.
- 모든 패스너를 고정하세요: Hand-tighten all screws initially. Once all components are in place, gently tighten them with the provided Allen key. Avoid over-tightening.
- 안정성 확인: After initial tightening, place the stand on a flat surface. If it wobbles, slightly loosen all screws, allow the stand to settle so all feet are in contact with the ground, then re-tighten the screws. This ensures proper alignment and stability.
- 고무 발 부착: Ensure all rubber feet are securely attached to the bottom of the stand for enhanced stability and floor protection.
Image: Components of the Monkey Loop Floor Prime 3 Guitar Stand, showing its foldable structure for transport or initial assembly.
Image: Close-up of the stand's base, highlighting the protective rubber padding and stable feet.
Image: Detail of the top support bar, showing the individual cradles designed to hold guitar necks securely.
작동 지침
Once assembled and stable, the stand is ready for use:
- 놓기: Position the stand in a safe location, away from obstacles and foot traffic.
- Loading Guitars: Gently place the body of each guitar onto the padded base of the stand. Ensure the bottom of the guitar rests fully on the padding.
- Securing Necks: Guide the neck of each guitar into one of the top cradles. The cradles are designed to hold the neck securely without damaging the finish.
- 균형: For optimal stability, distribute the weight of the guitars evenly if possible, especially if not all three slots are used.
- Unloading Guitars: Lift the guitar neck out of its cradle first, then carefully lift the guitar body off the padded base.
Image: The Monkey Loop Floor Prime 3 Guitar Stand holding three guitars (electric and acoustic), demonstrating proper instrument placement.
관리 및 유지 보수
- 청소: Wipe the stand with a soft, dry cloth to remove dust. For stubborn dirt, a slightly damp 천을 사용하여 세척 후 바로 말리세요. 연마성 세척제나 용제는 사용하지 마세요.
- 패딩 검사: Periodically check the rubber padding on the base and neck cradles for any signs of wear, tears, or deterioration. Damaged padding should be replaced to prevent instrument damage.
- 패스너 점검: Every few months, inspect all screws and connections to ensure they remain tight. Re-tighten if necessary to maintain structural integrity.
- 저장: When not in use for extended periods, the stand can be folded for compact storage. Store in a dry environment.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| Stand wobbles or is unstable | Uneven assembly; loose fasteners; uneven floor surface. |
|
| Guitars do not sit securely | Incorrect placement; damaged padding. |
|
| 조립 중 부품 누락 | Parts overlooked in packaging. |
|
명세서
| 모델명 | Monkey Loop Floor Prime 3 Guitar Stand |
| 모델 번호 | 10176054 |
| 상표 | 원숭이 루프 |
| 재료 | 합금강 |
| 마무리 유형 | 우아한 |
| 색상 | Multicolor (primarily black with yellow accents) |
| 품목 무게 | 2 킬로그램 |
| 제품 크기(L x W x H) | 15 x 11 x 62 cm (folded/packaged) |
| 용량 | 3 Guitars (Acoustic, Electric, or Bass) |
| 원산지 | 중국 |
보증 및 지원
For product support, warranty information, or to inquire about replacement parts, please contact the official distributor:
Madridhifi.com
As the official distributor of Monkey Loop products, Madridhifi.com is committed to providing excellent service and quality support for your equipment and accessories.
구체적인 보증 조건 및 연락처는 구매 서류를 참조하십시오.