1. 서론
This manual provides detailed instructions for the assembly, operation, and maintenance of your Antec NX410 ATX Mid-Tower Case. Please read this manual thoroughly before beginning installation to ensure proper setup and to maximize the performance and longevity of your system.
Figure 1.1: Antec NX410 ATX Mid-Tower Case (Black)
2. 주요 특징
- 고급 냉각: Pre-installed with 2 x 140mm ARGB fans in the front and 1 x 120mm ARGB fan in the rear for efficient airflow.
- 강화 유리 측면 패널: A full-side view tempered glass panel allows for showcasing internal components and RGB lighting.
- 최적화된 공기 흐름: Features a grid front panel design to enhance air intake and maintain optimal temperatures.
- 마더보드 지원: ATX, Micro-ATX 및 ITX 마더보드 폼팩터와 호환됩니다.
- Amp확장: Supports various storage configurations and large graphics cards (up to 335mm) and CPU coolers (up to 168mm).
3. 설정 및 설치
3.1 사건 준비
Before installing components, ensure the case is placed on a stable, flat surface. The tempered glass side panel can be easily opened via a magnetic latch for access to the interior.
Figure 3.1: Internal Component Layout and Compatibility
3.2 마더 보드 설치
The NX410 supports ATX, Micro-ATX, and ITX motherboards. Install standoffs as required by your motherboard's form factor before mounting the motherboard.
3.3 팬 및 라디에이터 지원
The case comes with pre-installed ARGB fans. Additional fans or radiators can be installed as follows:
- 앞쪽: Up to 3 x 120mm or 3 x 140mm fans (up to 360mm radiator).
- 맨 위: Up to 2 x 120mm or 2 x 140mm fans (up to 280mm radiator).
- 뒤쪽: 1 x 120mm fan (up to 120mm radiator).
Figure 3.2: Fan and Radiator Configuration
Important Fan Connection Note:
Figure 3.3: Fan Installation Warning
- If you connect the major fan and other fans but do not connect the major fan to the motherboard, other fans will not function.
- The fan kit does not work in sync with the motherboard ARGB function unless properly connected.
3.4 저장 드라이브 설치
The case provides bays for 3.5-inch HDDs and 2.5-inch SSDs. Refer to the internal layout diagram (Figure 3.1) for specific mounting locations.
3.5 전원 공급 장치(PSU) 설치
The PSU mounts at the rear bottom of the case. Ensure the PSU length does not exceed 165mm for optimal fit and cable management.
4. 케이스 기능 작동 방법
4.1 전면 패널 I/O 포트
The top front panel provides convenient access to essential ports and controls:
- 전원 버튼
- LED 제어 버튼
- USB 3.0 x 1
- USB 2.0 x 2
- HD-AUDIO (Headphone and Microphone jacks)
그림 4.1: 전면 패널 I/O 포트
4.2 ARGB 조명 제어
Use the dedicated LED Control Button on the front panel to cycle through various ARGB lighting effects and colors for the pre-installed fans. This allows for customization of your system's aesthetic.
Figure 4.2: LED Control Button
5. 유지관리
5.1 먼지 필터 청소
The Antec NX410 features a fine mesh front panel and a magnetic dust filter on the top panel to prevent dust buildup. Regularly remove and clean these filters to maintain optimal airflow and cooling performance.
Figure 5.1: Fine Mesh Front Panel
5.2 내부 구성 요소 접근
The tempered glass side panel is secured with a magnetic latch, allowing for tool-less access to the internal components for upgrades, cleaning, or troubleshooting. Gently pull the handle to open the panel.
6. 문제 해결
- 시스템 전원이 켜지지 않음: Ensure all power cables (24-pin ATX, 8-pin CPU, GPU PCIe) are securely connected to the motherboard, graphics card, and power supply. Verify the power supply switch is in the 'ON' position.
- 팬이 회전하지 않음/RGB가 작동하지 않음: Check fan connections to the motherboard or fan controller. Ensure the LED control button is pressed to cycle through modes. Refer to Figure 3.3 for proper fan wiring.
- 과열 문제: Confirm all case fans are installed correctly and spinning. Clean dust filters regularly. Ensure proper thermal paste application on the CPU cooler.
- USB 포트가 작동하지 않음: Verify the USB headers from the front panel are correctly connected to the motherboard.
7. 사양
| 특징 | 세부 사항 |
|---|---|
| 상표 | 안텍 |
| 모델명 | NX410 |
| 케이스 유형 | 미드 타워 |
| 마더보드 호환성 | ATX, 마이크로 ATX, ITX |
| 치수(D x W x H) | 15.35인치 깊이 x 8.27인치 너비 x 19.09인치 높이 |
| 재료 | 강화 유리, 강철 |
| 사전 설치된 팬 | 2 x 140mm ARGB (Front), 1 x 120mm ARGB (Rear) |
| 최대 CPU 쿨러 높이 | 168mm |
| 최대 GPU 길이 | 335mm |
| 최대 PSU 길이 | 165mm |
| 확장 슬롯 | 7 |
| I/O 포트 | Power, LED Control Button, USB 3.0 x 1, USB 2.0 x 2, HD-AUDIO |
| 하드 디스크 폼 팩터 | 3.5 인치 |
| Internal Bays Quantity | 2 (3.5" HDD / 2.5" SSD Convertible), 3 (2.5" SSD) |
8. 보증 및 지원
The Antec NX410 ATX Mid-Tower Case comes with a 2년 보증. For technical support, troubleshooting assistance, or warranty claims, please visit the official Antec web사이트를 방문하거나 고객 서비스 부서에 문의하세요. 보증 확인을 위해 구매 증빙 자료를 보관하세요.