Torin BIG RED AT825010-9B Floor Jack Rubber Pad Instruction Manual

1. 서론

The Torin BIG RED AT825010-9B Floor Jack Rubber Pad is designed to provide a protective barrier between your floor jack and your vehicle's frame rails. This durable rubber pad helps prevent damage, scratches, and deformation to the vehicle's pinch welds and undercarriage components during lifting operations. Its universal slotted design ensures compatibility with most standard floor jacks, making it an essential accessory for safe vehicle maintenance.

Figure 1: Torin BIG RED AT825010-9B Floor Jack Rubber Pad, showing its robust construction and slotted design.

2. 안전 정보

경고: 이 안전 지침을 따르지 않을 경우 재산 피해, 심각한 부상 또는 사망에 이를 수 있습니다.

일반 안전 예방 조치:

• Always read and understand the instruction manual for your floor jack before use.
• Ensure the vehicle is on a flat, stable, and level surface before attempting to lift.
• 차량을 잭으로만 받쳐놓은 상태에서 차량 아래에서 작업하지 마십시오. 차량을 들어 올린 후에는 항상 적절한 잭 스탠드를 사용하여 차량을 지지하십시오.
• Verify that the jack pad is correctly seated on the floor jack's saddle and aligned with the vehicle's designated lifting point (pinch weld or frame rail).
• Do not exceed the weight capacity of your floor jack or the jack pad.
• 들어올리고 내리는 작업 중에는 움직이는 부품에 손과 발이 닿지 않도록 주의하세요.
• Inspect the jack pad for wear, cracks, or damage before each use. Replace if any damage is observed.
• 안전 안경과 장갑 등 적절한 개인 보호 장비를 착용하세요.
• 어린이와 주변 사람들이 작업장에서 멀리 떨어지게 하십시오.

3. 패키지 내용

패키지를 열었을 때 모든 품목이 들어 있는지 확인하세요.

• Torin BIG RED AT825010-9B Floor Jack Rubber Pad (Quantity: 1 or 2, depending on purchase option)

4. 설정

The Torin BIG RED AT825010-9B Floor Jack Rubber Pad requires minimal setup. Follow these steps to prepare for use:

1. 잭 패드를 점검하십시오: Before first use, and prior to each subsequent use, thoroughly inspect the rubber pad for any signs of wear, cuts, cracks, or deformation. Ensure the material is intact and free from damage that could compromise its integrity.
2. Clean the Jack Pad: Wipe the jack pad clean of any dirt, grease, or debris to ensure a secure grip on both the floor jack and the vehicle.
3. 호환성 확인: Confirm that the dimensions of the jack pad are compatible with your floor jack's saddle. The universal slotted design is intended to fit most standard floor jack saddles.

그림 2: 차원 view of the jack pad, illustrating its size and slotted design for compatibility assessment.

5. 사용 설명서

Using the Torin BIG RED AT825010-9B Floor Jack Rubber Pad correctly is crucial for protecting your vehicle.

1. 차량 위치를 정하십시오: Park the vehicle on a firm, level surface. Engage the parking brake and, if applicable, place the transmission in 'Park' (automatic) or 'Reverse' (manual). Block the wheels that will remain on the ground.
2. Place the Jack Pad: Carefully place the Torin BIG RED AT825010-9B rubber pad onto the saddle of your floor jack. Ensure it is centered and stable.
3. Locate Lifting Point: Identify the vehicle's manufacturer-recommended lifting point, typically a pinch weld or a reinforced frame rail. Refer to your vehicle's owner's manual for precise locations.
4. 잭 위치: Roll the floor jack with the rubber pad underneath the designated lifting point. Align the slot in the rubber pad with the vehicle's pinch weld or ensure the pad is squarely under the frame rail.
5. 차량을 들어 올리세요: Slowly and steadily raise the floor jack, ensuring the jack pad maintains proper contact with both the jack saddle and the vehicle's lifting point. Observe for any slippage or misalignment.
6. 잭 스탠드를 설치하세요: Once the vehicle is at the desired height, immediately place appropriately rated jack stands under the vehicle's designated support points. Lower the vehicle slowly until it rests securely on the jack stands.
7. 잭을 제거하세요: Once the vehicle is safely supported by jack stands, lower the floor jack completely and remove it from under the vehicle.

Figure 3: The jack pad correctly positioned on a floor jack, engaging with a vehicle's pinch weld for safe lifting.

6. 유지관리

Proper maintenance will extend the life of your Torin BIG RED AT825010-9B Floor Jack Rubber Pad:

• 청소: After each use, wipe the rubber pad clean with a damp cloth to remove any dirt, oil, or debris. Avoid using harsh chemicals or solvents that could degrade the rubber material.
• 점검: Regularly inspect the pad for any signs of wear, cuts, cracks, or hardening of the rubber. Pay close attention to the slotted areas and edges.
• 저장: Store the jack pad in a clean, dry place away from direct sunlight, extreme temperatures, and corrosive substances.
• 대사: If the jack pad shows any signs of significant wear, damage, or loss of elasticity, replace it immediately to ensure continued safety and effectiveness.

7. 문제 해결

This section addresses common issues you might encounter with the jack pad.

8. 사양

9. 보증 정보

이 제품에는 다음이 포함되어 있습니다. Limited 1-year manufacturer warranty. For specific details regarding warranty coverage, terms, and conditions, please refer to the official documentation provided with your purchase or contact the manufacturer directly.

10. 고객 지원

For technical assistance, questions about product usage, or warranty claims, please contact Torin customer support. Contact information can typically be found on the product packaging or the manufacturer's official web대지.

Manufacturer Contact Information: ISSAQUAH, WA, 98027 US