소개
This manual provides detailed instructions for the assembly, operation, and maintenance of your ErGear Dual Monitor Stand, model EGCM3-E. Please read this manual thoroughly before installation and retain it for future reference. This monitor stand is designed to support two monitors ranging from 13 to 32 inches, with a maximum weight capacity of 8 kg (17.6 lbs) per arm.
안전 정보
- 조립하기 전에 모든 구성품이 있는지, 손상되지 않았는지 확인하십시오. 부품이 누락되었거나 불량인 경우 사용하지 마십시오.
- Do not exceed the maximum weight capacity of 8 kg (17.6 lbs) per arm. Overloading may result in instability and potential injury.
- This stand is compatible with VESA mounting patterns of 75x75mm and 100x100mm. Verify your monitor's VESA pattern before installation.
- Always use two people for lifting and mounting monitors to prevent injury.
- Ensure the stand is placed on a stable, level surface.
- 조립하는 동안 어린이와 애완 동물을 가까이 두지 마십시오.
패키지 내용
패키지에 모든 부품이 포함되어 있는지 확인해 주세요.
- 베이스 플레이트
- 지원 극
- 모니터 암(2)
- VESA 플레이트(2)
- 케이블 관리 클립
- 하드웨어 키트(나사, 와셔, 육각 렌치)
설치 지침
Step 1: Assemble the Base and Pole
Attach the support pole to the base plate using the provided screws. Ensure the connection is secure and stable.
The sturdy base plate provides stability for the dual monitor setup. Dimensions are approximately 41cm by 26cm.
Step 2: Attach Monitor Arms to the Pole
Slide the monitor arms onto the support pole. Adjust them to your desired height and tighten the securing mechanism. Note that both arms adjust vertically together.
3단계: 모니터에 VESA 플레이트 부착
Secure the VESA plates to the back of your monitors using the appropriate screws from the hardware kit. Ensure the VESA pattern (75x75mm or 100x100mm) matches.
Each arm is designed to hold monitors up to 8 kg (17.6 lbs) and supports VESA 75x75mm or 100x100mm mounting patterns for 13-32 inch screens.
4단계: 모니터를 암에 장착합니다
Carefully slide the monitors (with VESA plates attached) onto the monitor arms. Secure them in place with the locking screws or clips provided.
운영 및 조정
The ErGear Dual Monitor Stand offers a range of adjustments for optimal view편안함과 인체공학적 자세를 제공합니다.
높이 조정
To adjust the height of both monitors, loosen the collar on the support pole, slide the arms to the desired height, and then re-tighten the collar. The maximum height extension is approximately 42cm.
Monitors can be raised up to 42cm from the desk surface to achieve an ergonomic view잉 높이.
기울기, 회전 및 좌우 회전
Each monitor arm allows for flexible positioning:
- 경사: Adjust the monitor screen ±45° (up or down) to reduce glare and optimize view각도를 나타냅니다.
- 받침: Pivot the monitor 180° (left or right) to share your screen or change view잉 방향.
- 회전: 모니터를 360° 회전하여 가로 모드와 세로 모드를 전환하세요.
The stand allows for versatile adjustments including tilt, swivel, and full 360-degree rotation for each monitor.
Easily switch monitors between landscape and portrait modes for different tasks.
케이블 관리
The stand features integrated cable management clips to keep your workspace tidy and organized. Route your monitor and power cables along the arms and down the support pole using the provided clips.
Utilize the integrated cable management system to maintain a clean and organized desk environment.
유지
- 모든 나사와 연결부가 단단히 조여져 있고 안전한지 정기적으로 점검하십시오.
- 스탠드를 부드러운 천으로 청소하세요.amp 천으로 닦으세요. 연마성 세제나 용제는 사용하지 마세요.
- Do not lubricate any moving parts unless specifically instructed by the manufacturer.
문제 해결
모니터 수평이 맞지 않습니다.
Check if the VESA plates are securely attached to both monitors and the arms. Ensure the arms are at the same height on the pole. Minor adjustments can often be made by slightly loosening and re-tightening the VESA plate screws.
스탠드가 불안정하게 느껴집니다.
Verify that the base is on a flat, stable surface. Ensure all screws, especially those connecting the pole to the base, are fully tightened. Confirm that the combined weight of your monitors does not exceed the stand's capacity.
기울기/회전 조절에 어려움이 있습니다.
Some joints may have tension adjustment screws. Refer to the assembly diagrams for specific locations and use the provided Allen key to loosen or tighten as needed.
명세서
| 특징 | 사양 |
|---|---|
| 모델 번호 | EGCM3-E |
| 상표 | 에르기어 |
| 호환 가능한 화면 크기 | 13~32인치 |
| 팔당 하중 용량 | 8kg(17.6파운드) |
| VESA 호환성 | 75x75mm, 100x100mm |
| 기울기 각도 | ±45° |
| 회전 각도 | 180° |
| 회전 | 360° |
| 재료 | 스테인리스 스틸 |
| 색상 | 검은색 |
| 장착 유형 | 독립형 베이스 |
보증 및 지원
For warranty information or technical support, please refer to the documentation included with your purchase or contact ErGear customer service directly. Contact details can typically be found on the manufacturer's official web사이트 또는 제품 포장에 표시되어 있습니다.